Pros And Disadvantages Of Routing

The benefit of IT for work tasks is the ease of communication. Many attendees at a meeting may be invited quickly in one go rather than people

makes it difficult for programs to interface. Quite frequently data is just lost and not retrievable.

The Router protocols implemented will be a OSPF which stands for (open shortest path first). Because of the large network being introduced this protocol will be the most useful. This protocol operates on Internal Gateway Protocols by routing the most direct path and using the bandwidth most optimally. This not only reduces the use of

the routing protocol is simply flooding, S will broadest the data packets and then these data packets are rebroadcasted by every neighbor of S, and

The internet layer is built up of four core protocols: IP, IGMP, ICMP and ARP. Internet protocol (IP) is responsible for routing, IP addressing and breakdown/reassembly of data packets, address resolution protocol (ARP) is responsible for mapping an IP address to a device on the local network, internet control message protocol (ICMP) provides diagnostic information and error reports on lost packets, internet group management protocol (IGMP) controls who receives IP datagrams in a single transmission. The transport layer is built up of two core protocols: TCP and UDP. Transmission control protocol (TCP) sequences and acknowledges packets sent and their recovery when lost in transmission allowing the computer to make and maintain network conversations where applications exchange data, defined as a connection-oriented protocol meaning the connection is maintained until the programs has finished exchanging data. User datagram protocol (UDP) This is used to transfer small amounts of data when the use of error correction isn’t needed increasing the speed of the transmission, common in multi-player video games as the user will not need to receive packets of past events in the game so the error correction featured in (TCP) would be

load of servers and to increase access locality. It happens by changing the the amount of data or number of servers.

| Given a network topology and three or more routers and an IPv4 addressing scheme, implement RIPv1 routing protocol and confirm layer 3 connectivity.

In the location-based routing, sensor nodes are distributed randomly in an interesting area. They are positioned mostly by utilizing of Global position system. The distance among the sensor nodes is evaluated by the signal strength obtained from those nodes and coordinates are computed by interchanging information among neighbouring nodes. Location-based routing networks are;

In this example, we have three routers A, B and C. C’s E0 is directly connected to 192.168.3.0. And C’s routing table is (192.168.3.0; 0; E0) which shows that 192.168.3.0 is 0 hop away. RIP (Routing Information Protocol), running on C, tells B that 192.168.3.0 is reachable through C with a distance of 0. B adds 1 hop to the distance and enters the route to 192.168.3.0 into its own routing table which becomes (192.168.3.0; 1; S1). Now RIP is running on B and tells C that 192.168.3.0 is 1 hop away. Similarly, C adds 1 hop to the distance and enters the route to 192.168.3.0 into its own routing table which becomes (192.168.3.0; 2; S1).

This protocol use Dijkstra algorithm. It maintains a complex data base, also called as link state database, which contains full information about the remote routers and the exact network topology. The goal from this protocol is to provide similar information about network connection to each router, so each router can calculate the best route to each network this is happen when each router generates information about itself and pass these information to other routers in the network so each router make a copy of this information without changing it.

The sender establishes a priority order in accordance to the importance of the packets. This way the sender instructs to the routers in the intermediate nodes about the packets classified as of low priority that can be temporarily discarded. This way the load on the network does not become so heavy and the available bandwidth is better exploited.

In simulated network the source node designated as1 initiates the routing procedure by sending RREQ or Route Request message to its surrounding nodes. The RREQ message sent by the source node is denoted in the color green. The other RREQ messages are shown in cyan, yellow, black etc. The source node 1 is sending the RREQ message to its neighbour nodes 5, 6, 9, 11 and 13 and the links are formed shown by the green line. Every time node 5,6,9,11,13 is sending the RREQ message to its neighbour and the links are formed.

routing. In this chapter, we introduce some popular routing protocols in each of the three

RIPv2 has next hop addressed included in the routing updates, use of multicases addresses in sending updates.

Key tools utilized, variable length subnet masking and route summarization are explained as well. Here choosing the appropriate routing protocol is equally critical for a successful design. To implement different masks for the same major network it is necessary to have a routing protocol that supports VLSM. Such routing protocols are called classless routing protocols. They carry the mask information along with the route advertisements therefore allowing for the support of more than one mask.