Reactivities Of Some Alkyl Halides

Purpose: The purpose of this experiment is to observe chemical changes in common consumer products to determine if the chemicals are basic, acidic, or remain neutral when mixed with other chemicals.

Objective: The objective of this lab is to observe the synthesis of 1-bromobutane in an SN2 reaction, to see how a primary alky halide reacts with an alcohol.

The primary goal of this laboratory is to correctly identify an unknown substance. To achieve this task, one may use various tests that reveal both chemical and physical properties of a substance. By comparing the results of a known substance and the unknown substance, one may eliminate alternative possibilities and more accurately predict the undisclosed compound. Furthermore, by performing these tests, data can be collected and verified regarding chemical and physical properties of the unknown. Understanding the chemical properties of a known substance aids one’s understanding of the unknown based on comparative analysis of the results of the tests.

Experimental Method: A filtration apparatus was set up. Solid iron(III) chloride hexahydrate was dissolved in water. In a separate container, sodium acetate trihydrate (NaC2H3O2 x 3 H2O) was also dissolved in water. Sodium acetate trihydrate was then added to iron(III) chloride. 2, 4-pentanedione (C5H8O2) was dissolved in methanol; it was then added to the iron(III) chloride/sodium acetate solution. The product of this mixture was filtered, and the precipitate

Dichloromethane has a molar mass of 84.93 g/mol. It has a density of 1.325 g/mL at 25°C and a boiling point of 39.8-40.0°C. Dichloromethane is an irritant, a carcinogen, and highly toxic.

The objective of this laboratory experiment is to study both SN1 and SN2 reactions. The first part of the lab focuses on synthesizing 1-bromobutane from 1-butanol by using an SN2 mechanism. The obtained product will then be analyzed using infrared spectroscopy and refractive index. The second part of the lab concentrates on how different factors influence the rate of SN1 reactions. The factors that will be examined are the leaving group, Br – versus Cl-; the structure of the alkyl group, 3◦ versus 2◦; and the polarity of the solvent, 40 percent 2-propanol versus 60 percent 2-propanol.

Conduct studies on food, air, water and soil to determine how they are altered when coming into contact with medicines, garden chemicals and industrial chemicals

The solvolysis of t-butyl bromide is an SN1 reaction, or a first order nucleophilic substitution reaction. An SN1 reaction involves a nucleophilic attack on an electrophilic substrate. The reaction is SN1 because there is steric obstruction on the electrophile, bromine is a good leaving group due to its large size and low electronegativity, a stable tertiary carbocation is formed, and a weak nucleophile is formed. Since a strong acid, HBr, is formed as a byproduct of this reaction, SN1 dominates over E1. The first step in an SN1 reaction is the formation of a highly reactive carbocation, in which a leaving group is ejected. The ionization to form a carbocation is the rate limiting step of an SN1 reaction, as it is highly endothermic and has a large activation energy. The subsequent nucleophilic attack by solvent and deprotonation is fast and does not contribute to the rate law for the reaction. The Hammond Postulate predicts that the transition state for any process is most similar to the higher energy species, and is more affected by changes to the free energy of the higher energy species. Thus, the reaction rate for the solvolysis of t-butyl bromide is unimolecular and entirely dependent on the initial concentration of t-butyl bromide.

A unimolecular nucleophilic substitution or SN1 is a two-step reaction that occurs with a first order reaction. The rate-limiting step, which is the first step, forms a carbocation. This would be the slowest step in the mechanism. The addition of the nucleophile speeds up the reaction and stabilizes the carbocation. This reaction is more favorable with tertiary and sometimes secondary alkyl halides under strong basic or acidic conditions with secondary or tertiary alcohols. In this experiment, the t-butyl halide underwent an SN1 reaction. Nucleophiles do not necessarily effect the reaction because the nucleophile is considered zero order, (which makes it a first order reaction.) The ion that should have the strongest effect in an SN1 reaction is the bromide ion. The bromide ion should be stronger because it has a lower electronegativity than chloride as well as a smaller radius.

In a 25-mL round-bottom flask, 1-chlorobutane (5 mL, 4.32 g, 0.046 mol), sulfuryl chloride (1.6 mL, 2.7 g, 0.02 mol), 2,2’-azobis-(2-methylpropionitrile) (0.03 g), and a boiling chip were added. After a condenser and gas trap were attached to the flask, the mixture was heated to a gentle reflux in a steam bath for 20 min. The flask was then allowed to cool down quickly in an ice bath for a short time before a second portion of the 2,2’-azobis-(2-methylpropionitrile) (0.03 g) was added to the flask. The mixture was refluxed for another 10 min. before the flask was cooled in a beaker of water. The reaction mixture was then poured into a small separatory funnel already filled with water (10 mL),

SN1 reactions are considered unimolecular nucleophilic substitution mechanisms and are a first-order process. Meaning that the reaction forms a carbocation intermediate and that the concentration of the nucleophile does not play a role in the rate-determining step, which is the slowest step in the reaction. All of the SN1 reaction mechanisms in this procedure can react two different ways. The expected mechanism for these reactions would be that the carbocation would react with the weak nucleophile nitrate, attaching the nitrogen to the positively charged carbon. However, while nitrate is the intended nucleophile in all of the reactions, it is a poor nucleophile. The ethanol used in this reaction is a polar protic ionizing solvent,

Purpose: The purpose of this investigation is to learn how to write a proper lab report and how to

Many reactions that exist in nature involve a double displacement between ions and reactants with solvents. A bimolecular nucleophilic substitution, or SN2 reaction, involves a nucleophilic attack on a substrate and the departure of a leaving group. A nucleophile is a compound or ion that donates electrons to promote bond formation (Caldwell, 1984). In order for a leaving group in a compound to leave, it must possess the characteristics of a weak base and be able to occupy electrons. Several factors affect the rate and favorability of such reaction, such as (Bateman, 1940). In addition, the substrate that is attacked by the nucleophile is commonly an unhindered primary substrate to allow the reaction to occur quicker. An SN2 reaction follows the second-order rate law.

The purpose of this lab is to understand the process of eliminating an alkyl halide to form an alkene. The experiment is carried out by first converting the alcohol, 2-methy-2-butanol, into the alkyl halide of 2-chloro-2-methylbutane that will then be put through dehydrohalogenation that favors elimination reaction (E2) to create a mixture of 2-methyl-2-butene and 2-methyl-1-butene. A fractional distillation will be taken to purify the mixture and an additional gas chromatography will be done to further analyze the mixture composition. A bromide test will be done to determine the product of an alkene in the experiment.

The next test that is performed is the Biuret’s test. In this test the purpose was to determine if any of the twelve chemicals