Recrystallization Lab Report

An Erlenmeyer flask was used to accommodate the largest volume of recrystallization solvent calculated and was cooled in an ice bath to increase the yield of crystals. The solid was collected by vacuum filtration and washed with a small amount of ice water. The product is then dried to a constant mass by use of an oven and weighed. A small amount of the unknown was compared to two samples of acetanilide and phenacetin for a melting point range to determine the identity. The temperature of the unknown was recorded when the first trace of liquid can be seen and when the unknown was completely liquid.

In experiment two, 1.48g of the unknown solid was recovered. From this mass, it was determined approximately 30mL of boiling water was needed for crystallization of acetanilide and about 121mL for phenacetin. Phenacetin would require more solvent because it is less

Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.

The recrystallization technique utilizes the ability of a compound to dissolve within a hot solvent and produce a solution. As this solution cools, the solute reforms without impurities in a crystal lattice structure.1 For this to work properly, an appropriate solution that will not dissolve the solute at low temperatures, but will at high temperatures, must be used.1 There is no single solvent that will work well for every solute’s recrystallization; different solvents are better suited for some solutes than others.2 Some impurities that do not dissolve within the solvent can be filtered out while the solution is still hot, while other impurities that readily dissolve within the solvent shouldn’t recrystallize with the pure substance (as they are not concentrated enough to

The product was placed in a Craig tube and several drops of hot (100°C) solvent (50% water, 50% methanol, by volume) was added and heated until all of the crystals dissolved. The Craig tube was plugged and set in an Erlenmeyer flask to cool. Crystallization was induced once the mixture was at room temperature by scratching the inner wall of the tube. It was then placed into an ice bath for ten minutes until crystallization was complete. The tube was then

21) After all of the solid dissolves, move the flask from the hot plate and allow it cool to room temperature. After a while, crystals should appear in the flask.

The product was then suspended in 2 ml of water with a stir rod in a 50 ml Erlenmeyer flask and heated to boiling. Water was added in one milliliter increments until all the product was dissolved (18 ml added total). The saturated solution was allowed to slowly cool, and gradual white crystal formation was observed. Recrystallized product was collected once more by suction filtration with the Hirsch funnel once crystallization ceased. Collected product dried on a watch glass for a week, weighed 0.14 g (1.2 mmol), and the melting point was 139°-141°

The proof (twice the % alcohol) starts at its maximum and goes down (as the alcohol evaporates). If we start with a high concentration of alcohol, we will get the azeotrope (95% alcohol, 5% water) for a while, then the concentration will decrease.

Objective: The objective of this experiment is to use acid-base extraction techniques to separate a mixture of organic compounds based on acidity and/or basicity. After the three compounds are separated we will recover them into their salt forms and then purify them by recrystallization and identify them by their melting points.

The solution is then cooled and recrystallization of the solute occurs. For a solvent pair to

The objective of this experiment was to illustrate electrophilic aromatic substitution by synthesizing p-nitroanilide (as well as ortho) from acetanilide by nitration. The para form was separated from the ortho form based on solubility properties using recrystallization techniques.

The week after, a recrystallization was performed on the previous week’s crude product. The product ethereal solution was first heated on a steam bath until dry. During the heating, a beaker of methanol was collected and also placed on the steam bath. Once the product was dry, it was cooled to room temperature and then placed in an ice-water bath. The now boiling methanol was added to the crude crystals and a recrystallization was performed. Once completed, the now purified product was collected via Buchner vacuum filtration and stored in drawer to dry for a week. Afterwards, a melting point range of the purified product was obtained by using a Mel-temp apparatus. Lastly, an

SV (figure. 1) is antihyperlipidemic compounds which can reduce about 30% of LDL and total cholesterol in the body. In addition, SV was more tolerated by the body [1] than other antihyperlipidemic drugs, so that it became the drug of choice for most patients with hyperlipidemia [2]. Unfortunately, its solubility in water is very low, and it correlates with very low bioavailability [3]. One potential method to improve the simvastatin's solubility was made by co-crystal form. Co-crystal is a crystal whose a structured arrangement, consists of two main compounds (the active substance and the crystal-forming components) known as co-former with a certain stoichiometric ratio [4]. ASP and SAC are two examples of co-formers that used to increase solubility

Impurities that are present in the solution can be removed by extracting them from the original solvent into another solvent. This is done by mixing two immiscible (insoluble to one another) solvents (Manion, 2004). By mixing the

Once cooled, the mixture was then transferred to a separatory funnel using the funnel while avoiding adding the boiling chip. 10 ml of water was then added to the mixture. The mixture was gently shaken and the phases were allowed to separate. The funnel was then unstopped and the lower aqueous phase was drained into a beaker. 5 ml of 5% aqueous NaHCO3 was added and then shaken gently. A great deal of caution was taken into consideration because of the production of carbon dioxide gas which caused pressure to develop inside the funnel. The pressure needed to be released so the funnel was vented frequently. The phases were allowed to separate and the lower aqueous phases was drained into the beaker. After draining, 5 ml of saturated NaCl was added to the funnel and then shaken gently. Once again, the phases were allowed to separate and the lower aqueous phase was drained into a beaker. An ester product was produced and was transferred into a 25 ml Erlenmeyer flask. This organic product was then dried over anhydrous Na2SO4 to trap small amounts of water in its crystal lattices thus removing it from the product. Finally the ester was decanted, so that the drying agent was excluded from the final product.