Recrystallization Of Acetanilide Lab Report

An Erlenmeyer flask was used to accommodate the largest volume of recrystallization solvent calculated and was cooled in an ice bath to increase the yield of crystals. The solid was collected by vacuum filtration and washed with a small amount of ice water. The product is then dried to a constant mass by use of an oven and weighed. A small amount of the unknown was compared to two samples of acetanilide and phenacetin for a melting point range to determine the identity. The temperature of the unknown was recorded when the first trace of liquid can be seen and when the unknown was completely liquid.

In experiment two, 1.48g of the unknown solid was recovered. From this mass, it was determined approximately 30mL of boiling water was needed for crystallization of acetanilide and about 121mL for phenacetin. Phenacetin would require more solvent because it is less

Moisten filter paper with a few drops of solvent and turn on water vacuum to fullest extent

27. Heat the water to 40°C with an alcohol lamp by setting up the apparatus as shown in figure 3 below:

The recrystallization technique utilizes the ability of a compound to dissolve within a hot solvent and produce a solution. As this solution cools, the solute reforms without impurities in a crystal lattice structure.1 For this to work properly, an appropriate solution that will not dissolve the solute at low temperatures, but will at high temperatures, must be used.1 There is no single solvent that will work well for every solute’s recrystallization; different solvents are better suited for some solutes than others.2 Some impurities that do not dissolve within the solvent can be filtered out while the solution is still hot, while other impurities that readily dissolve within the solvent shouldn’t recrystallize with the pure substance (as they are not concentrated enough to

The vial was removed from the heat and cooled to room temperature. The spin vane was rinsed with 2-3 drops of warm water over the conical vial. The vial was cooled to room temperature then placed in an ice bath for 15 minutes. The liquid was decanted from the mixture and the resulting crystals were dried on filter paper. The crystals were then placed on a watch glass for further drying. The crystals were weighed and a small sample was placed into a capillary tube for melting point determination.

17) Pour a small amount of the hot solvent into the flask containing the solid.

To tube 2 and tube 3 a boiling chip is added. The two tubes are boiled to remove any residual ether. Next, the tubes are cooled to room temperature and placed into an ice bath to allow for crystallization. The solution is then removed from the solid in each tube and discarded. To tube 2 and 3 ~0.5 ml of H2O is added for recrystallization, the tubes

alcohol (2-methyl-2-butanol, MW _ 88.2, d _ 0.805 g/mL) and 25 mL of concentrated hydrochloric acid (d _ 1.18 g/mL). Do not stopper the funnel. Gently swirl the mixture in the separatory funnel for about 1 minute. After this period of swirling, stopper the separatory funnel and carefully invert it. Without shaking the separatory funnel, immediately open

XII. Take the 250 ml beaker to your lab bench. Set up a gravity filtration with a plastic funnel, folded wet filter paper, and an Erlenmeyer flask. Pour the content in the 250 ml beaker slowly through the filter paper. Wash the filter paper with deionized water. Dispose of the filtrate in the proper labeled waste container.

2) Rinse the solid with about 30 mL of distilled water and decant the liquid from the solid. It is critical that as little solid as possible is lost during this process. Repeat the rinsing two or three times.

1.) Transfer the distillate to separatory funnel. Fluid didn’t seem very clear but sufficient to finish our lab on time.

Once cooled, the mixture was then transferred to a separatory funnel using the funnel while avoiding adding the boiling chip. 10 ml of water was then added to the mixture. The mixture was gently shaken and the phases were allowed to separate. The funnel was then unstopped and the lower aqueous phase was drained into a beaker. 5 ml of 5% aqueous NaHCO3 was added and then shaken gently. A great deal of caution was taken into consideration because of the production of carbon dioxide gas which caused pressure to develop inside the funnel. The pressure needed to be released so the funnel was vented frequently. The phases were allowed to separate and the lower aqueous phases was drained into the beaker. After draining, 5 ml of saturated NaCl was added to the funnel and then shaken gently. Once again, the phases were allowed to separate and the lower aqueous phase was drained into a beaker. An ester product was produced and was transferred into a 25 ml Erlenmeyer flask. This organic product was then dried over anhydrous Na2SO4 to trap small amounts of water in its crystal lattices thus removing it from the product. Finally the ester was decanted, so that the drying agent was excluded from the final product.

An ice bath was prepared in a large beaker and a small cotton ball was obtained. 0.5 g of acetanilide, 0.9 g of NaBr, 3mL of ethanol and 2.5 mL acetic acid was measured and gathered into 50mL beakers. In a fume hood, the measured amounts of acetanilide, NaBr, ethanol and acetic acid were mixed in a 25mL Erlenmeyer flask with a stir bar. The flask was plugged with the cotton ball and placed in an ice bath on top of a stir plate. The stir feature was turned on a medium speed. 7mL of bleach was obtained and was slowly added to the stirring flask in the ice bath. Once all the bleach was added, stirring continued for another 2 minutes and then the flask was removed from the ice bath and left to warm up to room temperature. 0.8mL of saturated sodium thiosulfate solution and 0.5mL of NaOH solution were collected in small beakers. The two solutions were added to the flask at room temperature. The flask was gently stirred. Vacuum filtration was used to remove the crude product. The product was weighed and a melting point was taken. The crude product was placed into a clean 25mL Erlenmeyer flask. A large beaker with 50/50 ethanol/water

Step 1 and 2 was repeated by using distilled water by replacing the test solution.