Research Paper On Changing Oil

When putting the tire on is an effective idea to install the bottom lug nut first, since it will help keep the tire in the right position to install the other lug nuts with ease. As a rule, starting the lug nuts by hand and turning them three or more threads will prevent stripping out the threads. Next, you will use the lug wrench to tighten the lug nuts little past finger tight. After all the lug nuts are snug, then the car can be lowered so the tire begins to touch the ground. Straight off the lug nuts can get their final torque and should be done so in a star or a criss-cross pattern. Afterward, the car can be lowered and the tools can be put away. By the way, it’s always a beneficial idea to check the lug nuts after traveling about ten miles to assure they are still

That is how you change your oil a simple process that saves you money and keeps your car running for as long as you need

B. Almost everyone that owns a vehicle has had to take their vehicle in to a mechanic to get their oil change on their car. But if you want to save time and money you can always do it yourself.

tightened, it's time to add the new oil. Unscrew the oil cap on top of the engine and with the

The outer racer of the bearing is fastening into the boss. The whole subassembly is then attached with the steering arm, stub axle by means of welded joints and the plate welded to the chassis by means of Rod end bearing(2). The steering arm is joined with the steering rod by swivel joint as shown in the fig1.

First, you need to remove the oil fill cap under the hood so the oil will flow out freely. Be sure that you have a container for the used oil later; take it to recycle centers which are usually located around town. Remember that it is now illegal to dump oil anywhere. Next find the drain plug, which will be located on the bottom of the engine block. It is the only plug located usually in the middle of a black pan in the front of the vehicle. Be careful that you have the right plug because some transmissions are also equipped with a drain plug. Once the plug has been located, find the right size socket or wrench to fit it, and be careful not to round of the head of the drain plug when you are removing it. Then let the oil drain in to your container. When the pan has drained replace the plug, but do not over-tighten it because you can strip the treads out of pan. Next, you need to find the oil filter, which should be located on either side of the engine block. Then take the oil filter wrench and put it around the filter and remove the old filter. Then take your new filter and take a little

Step 3: Place the oil drain pan under the plug and loosen the plug with a socket wrench. Remember: turn counterclockwise to remove bolts.

1. Have you ever wondered how the things you buy get delivered to the stores? Semis, planes, trains, and sometimes boats. The majority of them run on diesel, because diesel is more efficient than a gasoline engine. With the number of diesels on the road everyday there is a high demand for mechanics that are properly trained to work on them. You have to be able to leave home on a moment’s notice to travel and repair trucks on the road. Being a diesel mechanic is very stressful and you never know what you will be working on day to day.

From the day in 1901 when a little hilltop near Beaumont began to gush oil,a big part of Texas changed that day. Oil has been changing our life ever since that historical day in 1901. Today, more than a century later, Texas still produces more oil than any other state in the Union.Oil has brought more wealth to Texas than ever before.

You will have to turn the lug nuts counter clockwise to loosen them. Do not remove the lug nuts all the way off the threaded shaft. Next, to get the wheel off the car, you have to raise the corner of the car where the flat is located.

After the tire is securely in place, screw on the lug nuts which should be located on the ground or in the hubcap as indicated in a previse step.

America has been in an oil crisis for many years, it should stop. People and companies are using more oil than they should. Oil supplies are fragile. If the United States drills for oil in several other countries it would cost a lot of money and gas prices will increase. There is an option of drilling in Alaska for oil. If the United States did drill it would be cheaper because it is domestic. If the United States collected oil from Alaska's wildlife it would have an overall positive outcome.

Oil also plays a big role in Canadian’s everyday lives. Not only does oil fuel our vehicles, cook our food and heat our homes and generate electricity; it is also used in almost everything we use on a daily basis. From rain, snow or sunshine and from head to toes, you could be wearing petroleum-based products. There’s more than gas in your vehicle, tires, mud flaps, wiper blades, your vehicle is an oil and gas machine. From the time, you wake up and put your coffee maker on, until you set your alarm clock at night. You’re using oil products. We use hundreds of petroleum-based oil products every day from household appliances, electronics, personal products and much more. In an article about oil and Canada’s future it states “These along with

5.     Look under the car to find your oil reservoir, use the socket wrench to remove the nut. Before you do this, you should have an oil pan ready to keep the dirty oil. After you unscrew the nut, you should see a stream of motor oil draining out of the oil tank. Allow this process to occur for 5-10 minutes and make sure the oil is going into the oil pan. This is the most annoying part of the entire procedure because sometimes things can get messy. Also look for the oil filter and twist in open. We are going to replace it with a new one in our next step.

Step No. 1 — Locate the belt. Lift and secure the hood of your vehicle to locate the belt. Find the side of the engine where the serpentine belt weaves its way through a series of pulleys, and securely held in place with a tensioner and a bolt.