Essay on Science Fair Project Example

The objective of the experiment “Keeping it Liquid” was to figure out what it takes to keep a compound in a liquid form which caused a phase change. A phase change is when a substance changes from one state or phase to another. There are three main phases that normally occur and they are called Evaporation, Deposition, and Melting. Evaporation is where a liquid changes to a gas. An example of evaporation is when water drops form on the glass of a cold drink on a warm day. Deposition is where a gas vapor goes directly into the solid phase without becoming a liquid first. An example of Deposition often occurs on windows during the winter months. While Melting is where a solid turns into a liquid. Melting occurs when ice turn into a liquid when

Other substances that dissolve in water also lower the freezing point of the solution. The amount by which the freezing point is lowered depends only on the number of molecules dissolved, not on their chemical nature. This is an example of a colligative property. In this project, you'll investigate different substances to see how they affect the rate at which ice cubes melt. You'll test substances that dissolve in water (i.e., soluble substances), like salt and sugar, as well as substances that don't dissolve in water (i.e., insoluble substances), like sand and pepper. Which substances will speed up the melting of the ice?

In my project, I will do an experiment to find out which material makes ice melt the fastest while the temperature of the room will remain the same. This research is important because if you are short on ice and you need it you can figure out which material will make your ice last the longest if you have no insulation. For example, if you were in the desert and had a cooler you would know what to put in your cooler to make your ice last the longest. I will be testing with three different materials: steel, wood, and fabric. My hypothesis is if the steel retains the ice's cold temperature then it will take the longest for the ice to melt. My goal is to help cooler companies improve their coolers by outlining them with whatever material helps

The freezing point constant (Kf) of water is 1.86 °C m-1. Each mass amount and Van’t Hoff factor was calculated then analyzed in a table.

In order to fulfil the labs purpose, the lab was split into two parts. The first part consisted of measuring and determining the freezing point depression of the solution water. The second part consisted of measuring and determining the freezing point depression of a solution that consisted of water and an unknown solute.

The objective of this experiment is to test the melting point of ice against different variables. I will use a control of ice against air and test this next to ice in water, sugar on ice, salt on ice and Baking Soda on ice. By measuring the melting time of each element on an ice cube I will be able to tell which element affects ice’s melting properties at what rate.

The experiment will start with two ice cubes. One will have nothing added to it, the other will have ½ tsp of salt sprinkled over it. Each will be separate on two different plates/containers. Time will be kept with a stopwatch, and notes will be taken throughout the experiment on the percentage of ice that has melted at certain points in time.

The amount of tablets did effect the temperature of the water. Our findings made our hypothesis incorrect. The temperature of the water did increase as the number of the tablets increased also. In this experiment, the finding were quite surprising, simply because I thought that the temperature of the water will decrease as the amount of the number of tablets increased. In the real world I feel like this information would be beneficial, because it shows the reaction of an acid plus a base mixed with water.

Purpose: The purpose of this laboratory was to gain an understanding of the differences between the freezing points of pure solvent to that of a solvent in a solution with a nonvolatile solute, and to compare the two.

In this experiment, we investigate the change in temperature caused by adding a chemical substance into the water and dissolving it. The results recorded in the table below show that our hypothesis is correct.

Colligative properties, such as boiling point and freezing point, are dependent on the amount of solutes added, not necessarily their identities (LibreTexts, 2018). A fascinating concept related to freezing points is Supercooling. Supercooling is a state where liquids do not form ice even when they reach temperatures below their normal freezing point; they are trapped in a metastable state (Esrf.eu, 2018). The best example of this is clouds at high altitudes: they contain tiny droplets of water that do not have seed crystals, and therefore do not form ice despite the low temperatures (Esrf.eu, 2018). The concept of freezing point depression is applicable in many parts of everyday life.

The volume is definite if the temperature and pressure are constant. When a solid is heated above its melting point, it becomes liquid, given that the pressure is higher than the triple point of the substance. Intermolecular (or interatomic or interionic) forces are still important, but the molecules have enough energy to move relative to each other and the structure is mobile. This means that the shape of a liquid is not definite but is determined by its container. The volume is usually greater than that of the corresponding solid, the most well known exception being water, H2O. The highest temperature at which a given liquid can exist is its critical temperature.[5]

The purpose of this lab was to study colligative properties. These properties are properties that are affected when a solute is added to a solvent. Thus, the amount is important, not the actual type of substance, for the colligative properties. A couple types of this property are the freezing point and boiling point of a substance. (1)

These phases can go from one to another when affected by certain things, which is known as phase changes. To switch from a solid to a liquid, the solid must melt. On the other hand, to switch from a liquid to a solid, freezing must occur. Furthermore, to switch from a liquid to a gas, a process known as evaporation must take place. In contrast, to

An increase in internal energy is required to convert a solid to a liquid,. Conversely, a reduction in internal energy can cause liquids to freeze or solidify. When heat is added to a solid or a liquid, the temperature of the sample does not necessarily rise. During a phase change, heat is added to the sample without an increase in temperature. Heat absorbed or released as the result of a phase change is called latent heat. There is no temperature change during a phase change, thus there is no change in the kinetic energy of the particles in the material. Latent heat is an intensive