Soda Ash Analysis and Volumetric Analysis of a Carbonate-Bicarbonate Mixture

1. To titrate a hydrochloric acid solution of “unknown” concentration with standardized 0.5M sodium hydroxide.

An example would be pure water. Most of the time the pH is determined by pH paper but there are also other ways to determine the pH. For example, in this lab, cabbage juice was used. Cabbage juice is a great pH indicator because it can be homemade and easy to access.

The goal of this lab was to determine the amount of grams of sodium bicarbonate (NaHCO3) required to produce enough CO2 gas to completely fill the lab and also how many Alka-Seltzer tablets that would equate to. This was done by collecting CO2 gas by inverting a buret and submerging it under water in order to calculate the volume of CO2 released from a fragment of Alka-Seltzer tablet. The main component of Alka-Seltzer is sodium bicarbonate, used to neutralize excess stomach acid during illness through the following reaction that generates CO2:

The purpose of this experiment was to mix Alka-Seltzer with Hydrochloric acid in order to analyze Sodium Bicarbonate as an active ingredient in the Alka-Seltzer. The mixture will contain hydrochloric acid to only see the composition of Sodium Bicarbonate in the tablet once it reacts. The amount that reacted allowed us to determine how much of it is present in the tablet. The amount of sodium bicarbonate will be measure by using the ideal gas law PV=nRT. The experiment will be conducted in the lab, therefore we are going to use room temperature which ranges from 15 to 26 degrees celsius. At room temperature pressure ranges from 12.8 to 25.0 millimeters mercury according to its corresponding room temperature.In the ideal gas equation R is 0.08206latm/mol k which is a constant. Once we have those values we can calculates the number of moles that reacted in the mixture by solving for the missing value. With the number of moles we are able to find the mass in grams which is what will potentially tell us the composition of Sodium Bicarbonate in a tablet of Alka-Seltzer.

A buffer is a solution that resists changes in pH when H+, OH-, or H20 is added. By using standard lab equipment, a lab pro diagnostic tool, and acidic and basic solutions, the pH can be found. By recording the pH while adding a base or an acid gradually to a buffer solution you can find the capacity of each buffer to resist drastic changes in pH. The best buffers will keep a solution from becoming either too acidic or basic with the addition of a strong base or acid.

Explain the pH scale and how it is used to indicate acidic, alkaline, and neutral solutions.

PH is . a numeric scale used to specify the acidity or alkalinity of an aqueous solution. The tests my group and I did was Dissolved Oxygen, Nitrate, phosphate, and the alkalinity tests. We also tested the rocks to see if they could neutralize the rocks. Neutralize renders something in effective or harmless applying an opposite force of effect. The two rocks that we studied were limestone and sandstone.

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

Within an acid-base titration the titration curve resembles the strengths of the corresponding acids and bases. A strong acid will correspond with a weak conjugate base, and a weak conjugate acid will correspond with a strong base. This is based on the Bronsted-Lowry model. The weak acid will donate protons to the hydroxide ion. Weak acids will have a low Ka value, the Ka value is the tendency of the acid to dissociate:

An unknown sample was massed and put into three test tubes for three different trials. A gas transfer assembly was put together and hydrochloric acid was added to each sample in each test tube. A reaction between the carbonate sample and the acid occurred and the volume of carbon dioxide gas produced was recorded. This process was repeated three times. The mass

By using acid-base titration, we determined the suitability of phenolphthalein and methyl red as acid base indicators. We found that the equivalence point of the titration of hydrochloric acid with sodium hydroxide was not within the ph range of phenolphthalein's color range. The titration of acetic acid with sodium hydroxide resulted in an equivalence point out of the range of methyl red. And the titration of ammonia with hydrochloric acid had an equivalence point that was also out of the range of phenolphthalein.. The methyl red indicator and the phenolphthalein indicator were unsuitable because their pH ranges for their color changes did not cover the equivalence points of the trials in which they were used. However, the

The amount of soda ash needed for the experiment was calculated using the following equation: sample weight of unknown=0.1103M (18ml×150.99)/(10×2× %〖Na〗_2 〖CO〗_3 ) An analytical balance was used to weight the calculated amount of soda ash. A piece of weighing paper instead of a weighing boat was used. The mass was recorded. The weighed soda ash was transferred into a 250 mL beaker, then the sample was dissolved in approximately 70 mL of water. The pH meter and electrode was obtained, rinsed with DI water, and calibrated using pH 7 and pH 4 buffer. A burette was obtained, mounted on a ring stand, and filled with the standardized HCl solution, that was prepared in Experiment 2. Since magnetic stirring bars and stirring plates were not available, the students

In this lab a acid-base indicator phenolphthalein was used to determine endpoint of a reaction HCl(aq) and KOH(aq). At the end point all of the HCl(aq) would have reacted with KOH(aq), and the pH becomes 7. The phenolphthalein would changed colours from colourless to pink indication when enough KOH(aq) was added. The purpose of numerous trials was to use the average volume of the 3 trials with similar measurements.

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid

A standard acid solution like HCl can be used as titrant for the analysis of both soda ash and a carbonate-bicarbonate mixture. In the analysis of soda ash, the volume needed to neutralize the soda ash is used to compute for its alkalinity, in this experiment we obtained a 17.6 % alkalinity with an error of 15.14% In the analysis of a carbonate-bicarbonate mixture two indicators (phenolphthalein and methyl orange) were used. The first endpoint determines the half-neutralization of the carbonate and the second determines that of the