Sugar Concentration

Procedure: Measure the volume, mass, length and temperature of a variety of items. Create dilution of sugar water.

The purpose of this particular lab was to experiment and identify the chemical and physical changes throughout the experiment.

From the excel chart of Molarity vs. Density, what was the relationship between the molarity of the sugar solution and the

concentration was plotted in order to estimate the concentration of the unknown solution (Figure 3).

In Part C of the experiment, the process completed in Part B was performed again on the six Kool-Aid drink samples: black cherry, cherry limeade, grape, mixed berry, strawberry, and tropical punch. The cherry limeade, grape, mixed berry, and tropical punch samples were undiluted stock solutions that were used in the SpectroVis. The black cherry solution was diluted with a 2-fold dilution. The 3 mL of black cherry solution was diluted with 3 mL of deionized water. This was done because the Red 40 dye was too concentrated. The strawberry solution was first diluted by a 2-fold but the absorbances values were too high and fell outside the acceptable range of 0-1. Therefore, 8 mL of strawberry solution was diluted with 12 mL of deionized water. These values for all of the solutions were recorded in Table 5. The solutions were emptied down the sink. All the glassware and cuvettes were rinsed with deionized water and dried. The volumetric flasks and caps were returned to the appropriate containers.

One of the most important skills to have in the chemistry lab is the understanding of how chemicals will react. Knowing for example, how a chemical will react with a metal, is an excellent way of determining the amount of a particular metal in a deposit. This knowledge was used in this lab to determine the amount of copper in an unknown sample mixture. It is also known that the determination of the percent concentration of a certain solution, will directly effect the percent transmission and absorption of a solution, dependent upon its dilution. By first testing known concentrations of a solution, and plotting this information graphically, a line is formed

Three peaks are observed in Figure 1 (concentration of glucose vs. elution volume) which was expected due to the results in table 4 that show intervals of elution. The intervals of the elution are represented as peaks on the graph. The intervals are due to the glucose molecules that enter the beads of the column causing the glucose molecules to elute slowly. Two peaks are observed in Figure 2 (concentration of starch vs. elution volume), which was not expected. One peak was expected for the

In order to test the predictions of the hypotonic, hypertonic, and isotonic hypothesis for the solution  made during the study,  four samples of sucrose were taken and placed into two different beakers each containing a different concentration. Beaker 1 is  250- mL and contained 150-mL of 10% sucrose with dialysis tubing A, while beaker 2 (a large bowl) contained 1% sucrose, with dialysis tubing  B, C, and D. Tubing A contained 10-mL with 1% sucrose. Tubing B

To improve the results from the experiment buffer solutions that were not whole pHs could have been used e.g. pH 4.5, 5.5 etc. This would have provided more reliable results as a wider range of results would have been produced. Using pHs with decimals would also help to more accurately determine the optimum pH as the optimum may have been above or below the pH stated in the hypothesis; 8. In this experiment however the optimum is taken at 8 because the graph does not rise again.

There were several steps completed to prepare for the experiment. Three dialysis tubes were filled with approximately the same volume of distilled water and then were tied shut. The initial mass (in grams) of the tubes was taken using a triple beam scale. I then filled three 500 mL beakers with 400 mL of water each and dissolved different masses of solute (table sugar) in each beaker in order to make 5%, 10%, and 20% solutions. The beakers were labeled accordingly, and then 20 g, 40 g, and 80 g (respectively) of table sugar was weighed out using a digital scale and placed into the corresponding beakers. The sugar was stirred in using a stirring rod until all of the solute was completely dissolved.

To calculate the concentration of the sucrose and glucose after the first reaction, and the final concentration of glucose of the samples of Powerade and Gatorade, the Beer-Lambert equation was used.

The purpose of this lab was for the student to get involved with his or hers new lab kit as well as being able to know, identify and use each other tools provided in the kit. Another key learning aspect of this lab is to teach the student how to measure properly the many units in the SI system. I will be using laboratory dilutions, measurements, and weights to then calculate using algebraic formula.

In my experiment, I was trying to find the answer for my main question which is, what drinks out of Coke, Diet Coke, Red Bull, Gatorade, and Sunny D will have the highest glucose concentration level after adding the enzyme, invertase? I chose this experiment because when I first looked into the topic, it got me really interested learning about the role of enzymes in our body and the different types of sugars and how they fluctuate our blood glucose levels. I decided to do this project since I thought that many people could learn and benefit from my information and I would also enjoy doing it. My experiment consisted of me taking five different drinks and using glucose urine test strips, to test the amount of glucose present in these drinks before and after adding invertase.

1. 5 sucrose solutions were made of increasing molarity: 0.2 M, 0.4 M, 0.6 M, 0.8 M, 1.0M. 2. 50 mL of each unknown solution were poured into 5 separate cups. A slice of potato was placed into 5 equal cylinders. 3. The mass of the 5 potato cylinders were then recorded. 4. The cylinders were placed into the foam cups with solution and covered with plastic wrap. It is to be left overnight. 5. The room temperature was recorded in Celsius. 6. The cylinders are then to be removed from the cups and carefully blotted of any excess solution. 7. The mass of the potato cylinders were recorded afterwards.

2. Following solutions are added to the tubes and the pH of each tube is determined: