Synthesis Of Grignard Reagent And Benzaldehyde

Any amount of H2O present would react with and therefore ruin the Grignard reagent. The negative charge on the Grignard carbon would pop a proton off of water, and the resulting hydroxide would react with MgBr2. Since all of the water and moisture was removed, the reaction should run successfully. For this experiment’s reaction, bromobenzene is turned into phenylmagnesium bromide, a Grignard reagent. Then, the Grignard reagent is reacted with benzophenone to yield a molecule with a negative charge on the oxygen. This molecule is worked up and protonated to yield triphenylmethanol.

During the halogenation reactions of 1-butanol, 2-butanol, and 2-methyl-2-propanol, there is a formation of water from the OH atom of the alcohol, and the H atom from the HCl solution. The OH bond of the alcohol is then substituted with the Cl atom. Therefore all of the degrees of alcohol undergo halogenation reactions, and form alkyl halides as products. This is because the functional group of alkyl halides is a carbon-halogen bond. A common halogen is chlorine, as used in this experiment.

The purpose of this experiment was to synthesize the Grignard reagent, phenyl magnesium bromide, and then use the manufactured Grignard reagent to synthesize the alcohol, triphenylmethanol, by reacting with benzophenone and protonation by H3O+. The triphenylmethanol was purified by recrystallization. The melting point, Infrared Spectroscopy, 13C NMR, and 1H NMR were used to characterize and confirm the recrystallized substance was triphenylmethanol.

The Purpose of this experiment is for the students to learn how to use sodium borohydride to reduce benzil to its secondary alcohol product via reduction reaction. This two-step reaction reduces aldehydes by hydrides to primary alcohols, and ketones to secondary alcohols. In order for the reaction to occur and to better control the stereochemistry and yield of the product, the metal hydride nucleophile of the reducing agents such as LiH, LiAlH4, or NaBH4 must be carefully chosen. Being that LiAlH4 and NaBH4 will not react with isolated carbon-carbon double bonds nor the double bonds from aromatic rings; the chosen compound can be reduce selectively when the nucleophile only react with

As detailed in Pavia 's Organic Laboratory techniques the reaction is expected to proceed via the following reaction:

After 10 minutes the reaction liquid was separated from the solid using a vacuum filtration system and toluene. The product was stored and dried until week 2 of the experiment. The product was weighed to be 0.31 g. Percent yield was calculated to be 38.75%. IR spectra data was conducted for the two starting materials and of the product. Melting point determination was performed on the product and proton NMR spectrum was given. The IR spectrum revealed peaks at 1720 cm-1, which indicated the presence of a lactone group, and 1730 cm-1, representing a functional group of a carboxylic acid (C=O), and 3300cm-1, indicating the presence of an alcohol group (O-H). All three peaks correspond with the desired product. A second TLC using the same mobile and stationary phase as the first was performed and revealed Rf Values of 0.17 and 0.43for the product. The first value was unique to the product indicating that the Diels-Alder reaction was successful. The other Rf value of 0.43 matched that of maleic anhydride indicating some

Additionally, creating a dry environment for the reaction tried to reduce the formation of side products. One possible side product was benzene, which was formed during the protonation of the carbanion on the benzene ring during the formation of the Grignard reagent4. The carbanion was very basic meaning that if there was any water in the glassware or moist air in the environment, some of the carbanion will be protonated by the water creating benzene instead of

Once inverted, built-up gas was released by turning the stopcock to its opened and closed positions. This was repeated for about four times in one minute intervals. Then the layers were allowed to settle until a separation between liquids could be observed. Due to the low density of the product, the top layer was to be extracted. The bottom layer was carefully and slowly extracted out of the separatory funnel.

2. Plan: Each student in a group of three will work to create a reaction with the Benzonitrile Oxide with, cis-stilbene, trans-stilbene, or styrene in an Erlenmyer flask. With this Reaction solution thin layer chromatography will be performed using each reaction solution. The different reactions will then be compared by running co-spot TLC’s. An NMR of the crude products from each reaction will be taken.

This experiment was designed by conducting a substitution reaction to construct a complex compound (2-methylphenoxyacetic acid) from two simple parts; also known as synthesis - converting simple molecules into more complex molecules. A purification technique known as crystallization was used to purify the product. Suction filtration was used to filter out the product. The experiment was completed over a three-day experimental period.

The Grignard reaction is an important synthetic process by which a new carbon to carbon bond is formed. Magnesium metal is first reacted with an organic halide forming the Grignard reagent. The Grignard reaction is the addition of an organomagnesium halide (Grignard reagent) to a ketone or aldehyde, to form a tertiary or secondary alcohol, respectively. For example, the reaction with formaldehyde leads to a primary alcohol. Grignard Reagents are also used in the following important reactions: The addition of an excess of a Grignard reagent to an ester or lactone gives a tertiary alcohol in which two alkyl groups are the same, and the addition of a

The purpose of this experiment is to examine the reactivities of various alkyl halides under both SN2 and SN1 reaction conditions. The alkyl halides will be examined based on the substrate types and solvent the reaction takes place in.

The reaction took place in a conical vial and .2mL of each of the reactant samples were added to it along with some 95% ethanol. Two drops of NaOH were added shortly after and stirred at room temperature for fifteen minutes. The vial was cooled in and ice bath and crystallized. Vacuum filtration was performed to filter the crude product. The crude product was recrystallized using methanol and filtered again. We made one change to the procedure and instead of using .7mL of ethanol we

Through the use of the Grignard reaction, a carbon-carbon bond was formed, thereby resulting in the formation of triphenylmethanol from phenyl magnesium bromide and benzophenone. A recrystallization was performed to purify the Grignard product by dissolving the product in methanol. From here, a melting point range of 147.0 °C to 150.8 °C was obtained. The purified product yielded an IR spectrum with major peaks of 3471.82 cm-1, 3060.90 cm-1, 1597.38 cm-1, and 1489.64 cm-1, which helped to testify whether the identity of the product matched the expected triphenylmethanol. The identity of the product being correct was further confirmed by way of both proton and carbon-13 NMR spectra. This is due to the fact

The purpose of this lab was to synthesize triphenylmethanol from benzophenone and bromobenzene by the formation of a Grignard compound with the reagents bromobenzene and magnesium metal. The bromobenzene was first transformed into the Grignard compound and was then reacted with the benzophenone to make the final product. The mixture was then mixed with sulfuric acid and the organic layer was extracted via a separatory funnel. The mixture was then recrystallized from methanol and was allowed to dry and the percent yield, melting point, and the IR was obtained. The mass of the product obtained was 5.45 grams and the percentage yield was determined to be 41.95%. The melting point range obtained from the final product was 89-91°C