Tactix Case Study

Normally, the large automakers demand 0 defects from their suppliers. However, it is challenging for Metalcraft to achieve extremely low defect rate and succeed among rivals. Therefore, to solve the problem of control during the supply chain

This then translates to a 50% chance of not having inventory available during job opportunities. Therefore, opportunity costs might occur. The indifference of the production managers' in these aspects of inventory control is alarming and should be acted upon.

This is something that must be addressed in supply chain management because if one area of the company is operating below capacity the other sectors will not be able to make up this lack of production. Another main component of supply chain management is how to handle damaged goods. It is a waste of money to send out defective products because it costs the organization large amounts of money to recall the damaged materials back to the factory and replace them, slowing production efficiency. There must be quality controls and regulations that enable Ford to minimize inventory defects and returns. The Ford Motor Company must have damage control operations to continue manufacturing the same amount of automobiles so that they do not lose any necessary inventory. There must also be procedures in place that deal with delivery systems and the delays and unsuitable materials that could easily occur. This paper will fully break down the previous issues associated with the Ford Motor Company 's supply chain management and operations. SUPPLY CHAIN MANAGEMENT OF FORD Synopsis of Supply Chain Management as it Applies to Ford The definition of supply chain management (SCM) involves taking a systems approach to the entire supply chain with the overall goal of reducing the level of risk and uncertainty throughout the supply chain. This will ultimately permit lower

•Be sure to write a detailed procedure for each lab design so that the same procedure can be followed accurately by anyone who reads it. Include details on the setup, the control of variables, and how the rate of each trial will be compared.

* Our company’s sales forecast has been based on performance from previous years along with market circumstances. We are looking at the future of the business objectively which we then can evaluate past to

Company is facing a challenge of potentially higher inventory costs. Rising prices may further result in changes in customer behavior and preferences.

The second task that needed to be finished was to forecast the income statement and the balance sheet for the next two years. We grew sales at a 15% rate, which is the stated rate from Koh. Also, in forecasting the balance sheet, we only showed debt financing for the capital expenditure of the DVD manufacturing equipment, which was the requested structure. Other relevant facts and assumptions for preparing the financial forecast are stated below-

Recommendation:1. Improve Just-in-time systemSpartan Plastic Limited need to improve Just-in-time system, it is control aims to maintain inventory level at zero, with an immediate objective of reducing the capital tied to the inventories. It is an important principle that able to eliminating waste throughout the production system. The waste can occur, through excess inventories and overly large lot sizes, both of which can cause unnecessarily long customer lead times. Let's explain the role of the core JIT practices in enhancing manufacturing performance. JIT manufacturing requires the establishment of JIT supplier relationships with suppliers; Spartan in this case, that is able and willing to deliver the needed quantities of parts as the needs arise and without any defects.

Suppliers must supply the stock managers with good quality products. If however the products are bad quality

Considering these above mentioned features, to take over the company, it is essential for Joe Jr. to take due attention to a proper approach for inventory management, calculate an appropriate inventory level for each product, making it in line with the company’s business strategy, the market demand in the upcoming period:

When offers of reduced pricing are accepted for equipment, meeting delivery expectations becomes an important part of enhancing the customer experience to maintain satisfied loyal customers. An inventory specialist in the current distribution center would be given the additional task of segregating and maintaining inventory levels to meet the needs of the customer loyalty department.

In this case study, production and operations management (POM) issues of a mid-size company, named as Scientific Glass Inc., in a highly growing market are studied. Using the background information on past actions of the company to correct inventory management and their results, and considering the market leadership opportunity, how inventory management approach can be made better is explained by evaluating different alternatives from different aspects. In the first part, critical POM issues are mentioned, following that these problems are analyzed. In the third part, alternative options are listed and then they are evaluated. Finally, considering

Produce more products so there is less restocking issues but not more than the market calls for (supply and demand),

Tasks:  What should Alison do? o Develop plans to improve the inventory management o Develop time-based supply strategies to bring competitive advantages to the organization  Identify the functions and forms of inventory  What are alternatives for inventory management? o ABC classification o Supplier-managed inventories (SMI) o Just-on-time or Just-in-time (JIT) o Enhance the forecasting system (factor correlated with inventory variation)  Provide training programs for current and new hiring employees 1

After making some wise short-term investments at a race track, Chris Low had some additional cash to invest in a business. The most promising opportunity at the time was in building supplies, so Low bought a business that specialized in sales of one size of nail. The annual volume of nails was 2,000 kegs, and they were sold to retail customers in an even flow. Low was uncertain of how many nails to order at any time. Initially, only two costs concerned him: order-processing costs, which were $60 per order without regard to size, and warehousing costs, which were $1