Task 2 New Formart 3 9 2015 Essay

Technology innovation has made the internet more accessible and faster for the end user. 68 percent of households have broadband in the United States. “Broadband penetration” is now treated as a key economic indicator.

Also cable lines running to fiber optic lines, through routers. And lastly it could be radio waves that computers can broadcast and receive or a combination of the above mentioned which are connected to enable communication via a modem, network card, radio transmitter, or router etc… sending your credentials in packets from your console through cabling to local access networks, regional networks, core/long-haul networks and ocean networks.

Crossover cable - A crossover cable is a type of twisted pair copper wire cable for LANs (local area network) in which the wires on the cable are crossed over so that the receive signal pins on the RJ-45 connector on one end are connected to the transmit signal pins on the RJ-45 connector on the other end.

2. Backbone Cable : Backbone cabling is the inter-building and intra-building cable connections in structured cabling between entrance facilities, equipment rooms and telecommunications closets. Backbone cabling consists of the transmission media, main and intermediate cross-connects and terminations at these locations. This system is mostly used in data centers.

What technique used to by cable provider to enable data and voice on the same cable using different frequencies for video and data

Coaxial cable consists of a core of copper wire surrounded by insulation, a braided metal shielding, and an outer cover.

generated at power plants is carried by power lines to users, sometimes hundreds of miles away.

3. Coaxial: A single copper wire surrounded by insultation. More expensive than copper twisted pair

ii. Most manufacturers are recommending the use of UTP cable for cabling computer networks except for very noisy environments.

Ethernet Cables- Ethernet Cables will be utilized to connect all the network devices in the DesignIT LAN network. They will connect routers, switches, computers, and printers in the LAN network. I will utilize CAT5 Ethernet Cables for this network. The Ethernet cables will cost about $100 for DesignIT LAN network.

Ideas and information travel in different ways. In our daily lives, we may not realize it but the cables around us have great importance in order to receive and send messages. Most importantly, a fiber-optic cable carries information between two places using entirely light based or in other words, optical technology. I will address how the optical fibers work, the variety of uses, and lastly, the advantages and disadvantages of this technology.

Analog via 3.5 mm phone jack; digital via HDMI and, as of revision 2 boards, I²S

Signal Starts with the microphone on one end connected into the stage box with standard XLR cables, which through analogue to digital conversion in the box, is then sent out into the local rack via Ethernet networking which sends uncompressed, low latency audio signals over standard Ethernet network. Type of cable used determines the maximum distance connection can travel until it begins to have a loss, ie; 80m for Standard Cat5e, 130m for Cat7, 1500m with single optical fibre and 600m with 3x200m reels of multimode 50/125 optical fibre in series. Aside from a main out for the Ethernet cable there is an auxiliary out to act as redundancy in the event that the primary Ethernet cable runs into any problems. The Local Rack acts not only as another A/D Converter if any mic is connected from this point but also as the Digital Signal Processor which enables mathematical manipulation of analogue signals which

Fiber-optic has been widely adopted because of its benefits as compared to other mediums. First and foremost, Fiber-optic can be used to transmit signals over long distance. The use of optical cables in Fiber technology allows signals to be transmitted over long distance and maintain the integrity of such signals as compared to metallic cables. Secondly, optical cable allows transmission of broad bandwidth. Optical fiber are usually small in diameter and are light hence it is easy to install as it uses less space. Broadband can be transmitted through coaxial cable or radio system however, optical fiber is the best medium for

There are four basic types of connection media that are used for connecting separate computers together on the same computer network. Both categories are copper cabling, fiber optic cabling, wireless signal, and infrared signals. The first two types of connection media on our lives are known as bounded network media because they both use wire of some sort in order to connect or bound one computer to another on a network. Copper cables are the most commonly used of the four types of network connection media. Copper cabling sends data in binary format from one computer system on a network to another through the use of electrical signals. Fiber optic cabling follows copper cabling when it comes to frequency of use. Fiber optic cable has a completely different configuration for transferring binary data across the network from one computer system to another computer system. Unlike copper cable fiber optic cable does not use electrical signals when encoding binary data instead it transmits the data as pulses of light. Fiber optic cables transmit the binary data as light pulses in a similar fashion to the way copper cables use electrical pulses to transmit binary data. The next two types of connection media are known as unbounded network media due to the fact that they do not use any type of physical wiring to connect the different computer systems on a