Kinetics Lab Report

In reference to the collision theory, molecules act as small spheres that collide and bounce off each other, transferring energy among themselves when the collide. In order for a reaction to occur, there must be collisions between molecules. Through experimentation, factors are discovered that influence the reaction rates of chemical reactions include the concentration of reactants, temperature, surface area, the physical state of reactants, and a catalyst. This experiment regarding the factors that affect reaction rate tests the effects of increased concentration and

Introduction: In everything there are things called particles; and sometimes when two particles meet a chemical reaction occurs. Also, with different strategies the chemical reaction can be sped up or slowed down. This is measured with reaction rate which is used to measure the length of a chemical reaction.

Kinetics is the study of the rate of chemical processes. The kinetics of the reaction between crystal violet and NaOH was studied. In order to monitor crystal violet concentration as a function of time, a spectroscopic colorimeter was used. What is the rate law for decolorization of crystal violet? In order to figure this out, the rate of the reaction of crystal violet and sodium hydroxide must be found. In this experiment, the initial goals were to determine the overall rate law for the rate of decolorization of crystal violet in basic solutions as a function of time and to determine the rate law for the reaction including the actual value of k; Rate = k[A]x[B]y. The rate of a reaction was expected to depend on the concentrations

Introduction: Chemical reactions are dependent upon two factors: temperature and concentrations of substance. We can monitor the rate at which a chemical decomposes or the rate at which a chemical substance appears. In this experiment we will be measuring the rate of decomposition of hydrogen dioxide with the following reaction:

In this Crystal Violet Kinetics Lab, many procedures were performed order to experimentally determine the rate constant(k), for the rate of the reaction of the crystal violet solution and sodium hydroxide. To start, a Beers Law calibration experiment was conduction. Also, two kinetic experiments were ran using both 5ml and 10ml of sedum hydroxide in order to determine the reaction order(k^1), of the sodium hydroxide.

Make sure to use the same type of cuvette to keep the width consistent and to prevent any experimental error from arising. Obtain 5 of the same type of cuvettes and pre-rinse them thoroughly. Label them numbers one through five in increasing molarity. Then, fill each of the cuvettes with one of the five solutions you created back in Part A. We will first examine the solution that exhibits the highest concentration or molarity. Make sure to wipe the outside of the cuvette with a Kimwipe before placing into the SpectroVis Plus device. Observe the graph that is generated and make sure to take note where the maximum absorbance takes place.

The objective of the experiment was to observe different reactions with different chemicals. The experiments emphasized on the chemical changes occurring in acids and bases as well as color changes and bubble formations. The experiments allowed for a better understanding of the undergoing chemical changes in mixtures. Some mixtures instantly changed colors while others were transparent or foggy. Some mixtures produced thick color that created solids called precipitates. Mixtures KI + Pb(NO3)2 and NaOH + AgNO3 both produce noticeable precipitates after a while. It was interesting to see the different acidic and base reactions like the fuchsia color formation in NaOH + phenolphthalein.

15) Obtain the boiled chloroplast suspension, mix, and transfer 3 drops to cuvette 4. Immediately cover and mix cuvette 4. Insert it into the spectrophotometer's sample holder, read the percentage transmittance, and record it in Table 4.4. Replace cuvette 4 into the incubation test tube rack. Take and record additional readings at 5, 10, and 15 minutes. Mix the cuvette's contents just prior to each readings. Remember to use cuvtte 1 occasionally to check and adjust the spectrophotometer to 100% transmittance.

Where A is the initial absorbance when the experiment first starts, l is the path length of the cuvette (2.54 cm), and [CV]t is the initial concentration of crystal violet.

Apparatus: Spectrophotometer (UV-1201), cuvettes, water bath (set at 37°C), 200µl and 1000µl micropipettes and test tube

The rate law of a chemical reaction is a very useful equation that relates the concentration of reactants to time. The law was formed from the results of experiments by various European chemists throughout the second half of the 1800s, when they caught on that there was a correlation between the concentration of reactants and time. The most basic formula of the equation is Rate=k[A]n[B]m..., where Rate is the rate of the reaction in concentration per second (M/s), k is a constant, [A] and [B] are the concentrations of the reactants (M), and n and m are values that rate to the order of each reactant. All the values in the equation can be determined experimentally by taking the concentrations of reactants and the corresponding rate at multiple

Incorporation of assay controls included setting up a spectrophotomer and running the chart recorder with a full-scale deflection before the start of the assay. The set recorder had a corresponding value of 1 for the change in the absorbance. Therefore, prior testing was done to observe whether a change occurred in the readings. This helped to indicate that the results were valid, as they could have been affected by a fault during the setting up of the spectrophotometer. On the other hand this was considered as one of the controls for the experiment. Nevertheless, a new cuvette had to be used for each assay.

Chemical kinetics involving reaction rates and mechanisms is an essential part of our daily life in the modern world. It helps us understand whether particular reactions are favorable and how to save time or prolong time during each reaction. Experiment demonstrated the how concentration, temperature and presence of a catalyst can change the rate of a reaction. 5 runs of dilution and reaction were made to show the effect of concentration on chemical reactions. A certain run from the previous task was twice duplicated to for a “hot and cold” test for reaction rate. The prior run was again duplicated for a test with

This is a fair test because the only thing that is changed is the drop

Kinetics of chemical reactions is how fast a reaction occurs and determining how the presence of reactants affects reaction rates. In this experiment the rate of reaction for Fe+3 and I- is determined. Because the rate of chemical reactions relates directly to concentration of reactants, the rate law is used to find the rate constant, and calculated with specified temperatures.