The Importance Of Phytochemical Screening Of Plant Organization

The unknown sample was identified to contain Acetaminophen, Aspirin, and caffeine based on comparison of known Rf values (Table 1). When comparing the traveled UV lit spots (figure 1), Aspirin and Ibuprofen traveled the same distance from the start line. Unknown sample 16 contains Aspirin not Ibuprofen, due to the intensity of the spot under UV light. Aspirin and the unknown shared that same intensity, whereas Ibuprofen did not share that same strength of brightness. The distance traveled by the samples was dependent upon their affinity for the mobile phase 200:1 ethyl acetate – acetic acid. The samples that traveled the furthest like the Aspirin and Ibuprofen were the most soluble in the mobile phase. The samples that traveled the shortest

There are various techniques to separate a mixture of compounds from each other. One of the commonly used way to isolate compounds from a mixture of two compounds is called extraction. This method of extracting two compounds from each other relies on the different solubility of the compounds in two different solvents.

Lycopene and β-carotene are separated using thin layer chromatography (TLC). A mixture of tomato paste containing dissolved lycopene and β-carotene is first spotted on a TLC plate. The technique uses a stationary phase layer, on which the substances stick, and a mobile phase, which migrates upwards the plate and carries the components of the mixture with itself (Chemguide). Depending on their respective polarity, lycopene and β-carotene stick more or less to the stationary phase and so they migrate up the TLC plate at different rates (Chemguide). Thus, as the chromatography is completed, the two components will appear as distinct dots at different heights on the plate. Lycopene has a bright orange color, whereas β-carotene is light yellow.

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

Other information that can be obtained from a TLC analysis is the progress of a chemical reaction, which can be done by taking samples from the reaction mixture at various intervals and spotting them on TLC plates and taking down the Rf factor. Also TLC analysis can be used to determine the optimum conditions required to obtain a high yield of the desired product with little to no side products. Yield can be ascertained via TLC analysis in that the reactant and product intensity on the TLC plate will have varying degrees of intensity. At the end of the reaction, the product should have the most intensity, while the reactant has the least intensity. At the beginning of the reaction, it would be the other way around. With this, you can determine the percent yield of the

The purpose of this experiment is to determine the specific pigments that are found in each of the chosen plant leaves, as well as, discover the intermolecular forces present in each leaf. This is accomplished by using a technique called chromatography, which splits a mixture or solution into its different parts based on the mixtures ability to dissolve in a chosen solvent. Chromatography works by placing a strip of chromatography paper, that has a small amount of mixture on it, into a cup of the specific solvent chosen. In this experiment, one hundred percent acetone was chosen to be the solvent. Once the small amount of the mixture is aligned with the solvent, the mixture will begin to separate and rise by capillary action based on the solubility,

0.300 grams of biphenyl/ p-toluidine sample was weighed. Next, 10 mL of dichloromethane was measured in a graduated cylinder. The dichloromethane was transferred to a small beaker then the solid mixture was dissolved in it. A Thin Layer Chromatography (TLC) was conducted with the dissolved mixture in 20% Ethyl Acetate and 80% Hexane solution. The TLC plate was observed to be impure with two spots. To being extraction, a separatory funnel was placed inside of the hood and the stopcock was closed. A flask was placed under the funnel then the mixture was added to the funnel. Next, 10 mL of 3M HCL was measured in a graduated cylinder and

• Working on HPLC requires heavy processing before estimation like mixing, homogenization, filtration, degassing, derivatization etc. These techniques are also to be performed with proper care to avoid problems in estimation.

On a thin chromatography plate, five spots were placed ( as shown in table 2) and the plate was developed using chloroform/methanol. This was later visualized with dragendorff’s reagent under the UV light. All separated components were observed, identified and recorded.

Varying concentrations of chemically-manufactured acetone solution were used in this experiment, which also acted as the control for the detection of acetone. Measurement was made using the UV-Vis spectrophotometer.

The purpose of this experiment was to use solvent extraction techniques in order to separate a mixture consisting of a carboxylic acid (p-toulic acid), a phenol (p-tert-butylphenol), and a neutral compound (acetanilide). Extraction is the process of selectively dissolving one or more of the compounds of a mixture into an appropriate solvent, the solution that contains these dissolved compounds is called an extract (Manion, 2004).

     In liquid chromatography, the separator is called the column and consists in most cases of a tube filled with porous material called the stationary phase. A liquid, called the mobile phase, flows through the tube between the particles of stationary phase material. A liquid sample is taken from a mixture to be analyzed and introduced to a part of the system that is at elevated pressure. The sample is then transported to a separator by the flow in the system.

In this experiment, the use of a glass cuvette was used in order to avoid any chemical or environmental interference from the surroundings. Furthermore such glass cuvettes can support large wavelengths during transmission of light beyond 320 nm since this is the excitation wavelength region. Riboflavin is excited at around 370 nm, therefore the wavelength range must be large in order to detect a proper response. Plastic cuvettes are however inadequate as the range of wavelengths supported for transmission of light is very limited (5, Upstone). The geometry of the instrument of the spectrophotofluorometer has a specific angle and position for the excitation source and the detector. The excitation polychromator emits ultra-violet radiation and light to the interested sample and the shape of the polychromator resembles a triangular prism in which the monochromator has been angled at a 90∘ position. The transducer would detect the irradiation excitation beam and transfers it through the emission polychromator. The emitted beam would then travel to the detector to allow for the response signal to appear for the sample on the computer system (416, Skoog). The position of the cuvette is essential as it enables for the consistent readings of the response signals, as any shift in the cuvette position can create variation in results due to the position of lighting and detection of molecular samples hitting at different angles. The process of fluorescence is quite sensitive than absorption due to having lower detection limits because of the fact that it can detect lone molecules in excited states that are irradiated by UV-light unless they come into contact with other molecules within

By Using specific methods of compounds detection, we can match an unknown compound with a known compound because similar compounds will display similar characteristics. In this experiment, identifications of the unknown ketone was accomplished using thin layer chromatography, melting point, and NMR spectrometry. Thin layer chromatography is very quick but sensitive way of determining the components of a mixture or a specific compound from a list of knowns. This method is the one which was utilized in the

AIM : Thin-Layer Chromatography can show many different characteristics of a mixture. It is recognized for isolation , separation ,identification, and anaylsis of the mixture’s components. The purpose of this experiment is to separate carbohydrates into its pure components such as mixtures of monosacrides by TLC. TLC is used to identify sugars in normal and pancreatic disease urine, the procedure is easy and reproducible .