The Legislative Process

Senator Jeffrey’s bill was to organize a camp for kids that need help. First Senator Jefferson has to propose the bill in front of Senate after he is done writing it, and after that it is sent into a committee to deem the importance of the bill. After that it is sent back and forth from the House and the Senate and is amended and voted yes or no on. If both the

Then, a reading clerk reads the bill section by section and the Representatives recommend changes. When all changes have been made, the bill is ready to be voted on.There are three methods for voting on a bill in the U.S. House of Representatives: Viva Voce, Division, and Recorded. If a majority of the Representatives say or select yes, the bill passes in the U.S. House of Representatives. The bill is then certified by the Clerk of the House and delivered to the U.S. Senate. When a bill reaches the U.S. Senate, it goes through many of the same steps it went through in the U.S. House of Representatives. The bill is discussed in a Senate committee and then reported to the Senate floor to be voted on. Senators vote by voice. Those who support the bill say “yea,” and those who oppose it say “nay.” If a majority of the Senators say “yea,” the bill passes in the U.S. Senate and is ready to go to the President.

Most individuals with a general background knowledge of the United States Federal Government system are aware that in order for a bill to become a law, it must first pass a majority vote in Congress. There is, however, a very important step in the legislative process that sometimes goes unnoticed. The committee system of the legislation process ensures that the appropriate attention is given to each bill introduced to Congress. Each member of both chambers are assigned to committees and subcommittees, and are expected to become subject matter experts in their respective roles as committee members.

As with the U.S., bills may be introduced by any member of either house, and approved by both houses. The existence of an upper house (Senate) in both Constitutions permits useful participation in public affairs to those who might not wish to run for election. Senate also encourages the patronage offerings of the major political parties.

As mentioned before, getting a federal law passed takes more steps than a state or local law. A member of Congress must first introduce the bill. After the bill is introduced to Congress it is then referred to a committee or multiple committees. The committee that the bill is referred to depends on what committee has jurisdiction over the primary issue of the bill (Steps in Making a Bill a Law: The Federal Legislative Process). Sometimes the bill is referred to a subcommittee first. According to, “Steps in Making a Bill a Law: The Federal Legislative Process,” once referred to a committee, “The chairman of the Committee determines whether there will be a hearing on the bill and whether there will be ‘mark up’” (Steps in Making a Bill a Law: The Federal Legislative Process). A “mark up” is when members of the committee meet to offer changes that could be made to the bill. After changes are accepted or rejected, the chairman moves to vote the bill favorably out of committee then the entire body of the committee favorably reports out the bill (Steps in Making a Bill a Law: The Federal Legislative Process). The third step to making a bill a law is a committee report. In this step, the committee chairman’s staff writes a report of the bill. The report of the bill describes the intent of legislation, the bill’s legislative history, the impact the bill will have on existing laws and programs, and the position that the majority of the members of committee take on the bill (Steps

After introduction of the bill, the referral or assignment to house or senate then takes place. In other words, the bill is assigned to standing committee. The Speaker and Lieutenant Governor appoint committee members and chairs. This gives the presiding officers great power and these vital decisions can

A Bill has a number of stages that it goes through before it is presented to the Queen to be signed. It starts off as a discussion in the House of Commons, and if decided to be an effective new policy idea then it is sent off

The process for each bill submitted is the same yet different; they all have to be accepted by several offices including the House of Representatives, Senate, and the president. In addition to that, they have to have the public's attention in order to make an impact on whether the bill is approved or not. Issues dealing with immigration are very common and bill H.R 3923, has the attention of representatives in the Senate including its sponsor, Representative Adam Smith, and important interest groups like the

All of the laws in the United States begin as a bill, which must be approved by the Senate, House of Representatives, and the President. The bill stars as an idea from a representative or a citizen who has an idea and tells their representative about the idea. The representative then decides if the idea is

Congress must always sponsor this bill before it is introduced to the House or Senate. Several drafts may even be composed by Congress, citizens of society, lobbyists, and coalitions. Primarily though, the President is the main source when it comes down to proposing one. The four forms of congressional action process as bills, joint resolutions, concurrent resolutions and simple resolutions. The introduction of a bill is the first step in the federal process is the referral to a standing committee where they have the power to delay, block or expedite

In the Senate, member can speak as long as they want. Once the debate is over the Senate will then vote on the bill. If fifty-one members vote in favor of the bill then it will be passed. The bill will then move on to a conference committee, which is made up of member from each House. The committee works out any differences between the House and Senates versions of the bill. The revised bill will then be sent back to both Houses for their final approval. Once approved, the bill is printed by the Government Printing Office in a process called enrolling. The clerk from the introducing house will certify the final version.

As nurses we strive to always practice in the best of our ability. One way that that we can further our efforts is to utilize our voice through health-care lobbying. The best approach to health-care lobbying is to first understand the legislative process. Consequently the purpose of this paper is to distinguish the legislative process as well as convey the benefits of health-care lobbying to not only the workers but the patients.

Comparing the Emplementation and Scrutinizing of Proposed Bills in the House of Commons and Congress

Anyone may draft a bill, which means an ordinary citizen can actually write a bill. Only members of Congress, however, can introduce legislation, and any of the congresspersons become sponsors. A bill can have anywhere from one sponsor to an entire party support. There are four general types of legislation; bills, joint resolutions (resolutions between both chambers but requires signing), concurrent resolutions (a joint resolution that does not require signing), and simple resolutions. The legislative process begins when a bill or resolution is numbered, (H.R. signifies a House bill and S. a Senate bill), referred to a committee, and printed by the Government Printing Office.

The Municipality of Kincardine started a study on the long term management of the L&ILW at the Bruce nuclear plant soon after the government introduced there nuclear waste management programs; although the management programs dealt only with high-level radioactive waste. Under Canada’s nuclear waste policy framework Ontario Power Generation (OPG) were responsible for the long term management of L&ILW at Bruce nuclear facility; Kincardine consequently signed an memorandum of understanding with OPG. Further, independent studies concluded several safe and feasible options for the long-term management of I&ILW at the Bruce nuclear plant. Kincardine asked for the option of Deep Geologic Repository (DGR)