The Reaction of Iron Nails with a Copper Solution Essay

Make sure the Classroom temperature is the same each time I do the investigation. This is because; a higher classroom temperature can increase the rate of reaction resulting in results that do not form a pattern.

Used stirring rods to completely remove copper from that wire. And then completed the removal of copper using 5 drops of 6M HCl, adding it onto copper. There will produced copper in a solution. Connected Buchner flask to the vacuum line and place filter paper in it to completely washed off the copper. Then, add 95% ethanol to copper and leave it for 1 min and turned section back for 5 mins. Measured mass of clean, dry watch glass. Transfer copper to watch glass and dry it under heat lamp for 20 mins, allowed it to cool to room temperature and then accurately determine its mass.

c) Record the amount of substance that dissolved – all, some, a little, or none.

The purpose of the experiment is to cycle solid copper through a series of five reactions. At different stages of the cycle, copper was present in different forms. First reaction involves reaction between the copper and nitric acid, and copper changed from elemental state to an aqueous. The second reaction converted the aqueous Cu2+ into the solid copper (2) hydroxide. In the third reaction Cu(OH)2 decomposed into copper 2 oxide and water when heated. When solid CuO reacted with sulfuric acid, the copper returned to solution as an ion (Cu2+). The cycle of reactions was completed with the reaction where elemental copper was regenerated by Zn and Cu

The mole is a convenient unit for analyzing chemical reactions. Avogadro’s number is equal to the mole. The mass of a mole of any compound or element is the mass in grams that corresponds to the molecular formula, also known as the atomic mass. In this experiment, you will observe the reaction of iron nails with a solution of copper (II) chloride and determine the number of moles involved in the reaction. You will determine the number of moles of copper produced in the reaction of iron and copper (II) chloride, determine the number of moles of iron used up in the reaction of iron and copper (II) chloride, determine the ratio of moles of iron to moles of copper, and determine the number of atoms and formula units involved in

The purpose of this lab was to determine the limiting reactant in a reaction between copper sulfate and iron. Using the reaction between copper sulfate and iron, the reaction was observed to see the reaction and transformation of matter. The copper sulfate was placed into a beaker, as the excess reactant, then iron filings added until the heated solution was completely reacted. This reaction created an excess of leftover. The law of conservation of mass can be observed in this reaction, and using the data found, the percent yield calculated.

Put approximately 9-10(g) copper ore into beaker. Use spatula to break up any large pieces. Next add 17ml H2SO4 (aq) (hydro sulfuric acid) to the beaker. Began mixing until all or most traces of blue dissipate; or the copper ore will no longer dissolve (should appear as a milky liquid). Next use pipette to and remove solution and divide solution into 2 individual test tubes then Place test tubes into centrifuge and run centrifuge for 1 minute. Remove from centrifuge machine Fill a cuvette with the clear solution from the test tube making sure not to disturb the sediment at the bottom. Note the solution should bluish in tint Final place the cuvette in the colorimeter. Then record data and calculate in results section.

The objective of this experiment will be to combine various substances, liquids and metals, and to observe their behavior when they are combined. The types of reactions observed shall determine the nature of these reactions: physical or chemical.

NH3. Add 20 mL water to the beaker by filling and emptying the 10 mL cylinder into the beaker

Then in the last test tube fill it up with 5ml of sodium sulphate. Then after that carefully pour the sodium carbonate solution into the test tube labelled copper chloride solution examining the result and recording appropriately.

The purpose of this experiment is to distinguish the relationships between reactants and products, in addition to expanding on concepts such as single displacement reactions, mole ratio values, moles to mass, theoretical yields, limiting reactants, excess, stoichiometric relationships and percentage errors.

Place 100 ml of distilled water in a 250-ml (or 400-ml) beaker. Add 1.26g of oxalic acid dihydrate (H2C2O4.2H2O) and 1 ml of concentrated ammonia. Stir the mixture until the solid has dissolved completely.

XII. Take the 250 ml beaker to your lab bench. Set up a gravity filtration with a plastic funnel, folded wet filter paper, and an Erlenmeyer flask. Pour the content in the 250 ml beaker slowly through the filter paper. Wash the filter paper with deionized water. Dispose of the filtrate in the proper labeled waste container.

Experimental approach: In the first reaction, copper metal turnings oxidize when put in contact with nitric acid and become copper nitrate.

The lab performed required the use of quantitative and analytical analysis along with limiting reagent analysis. The reaction of Copper (II) Sulfate, CuSO4, mass of 7.0015g with 2.0095g Fe or iron powder produced a solid precipitate of copper while the solution remained the blue color. Through this the appropriate reaction had to be determined out of the two possibilities. Through the use of a vacuum filtration system the mass of Cu was found to be 2.1726g which meant that through limiting reagent analysis Fe was determined to be the limiting reagent and the chemical reaction was determined to be as following:-