The Separation Process Of Naphthalene And Benzoic Acid

Different procedures were used to isolate benzil from the ether layer and benzoic acid from the aqueous layers. To isolate benzil, anhydrous MgSO4 was added to the flask containing the ether layer solution. MgSO4 removes the remaining water in the ether layer solution. After making sure that enough amount of MgSO4 present in the solution, the ether solution was filtered by using gravity filtration. During filtration, MgSO4 was removed from the solution and the ether solution was collected in 25 ml flask. To separate benzil from the filtered ether solution, the beaker containing the ether solution was heated until the ether evaporated. After letting the beaker to cool to room temperature, the mass of the beaker with the benzil crystals was measured. From the combined mass of the beaker and the benzil crystals and from the predetermined mass of the beaker, the mass of the collected crystals was calculated to be 0.266 gram.

This experiment combined all the knowledge of the previous labs performed throughout the semester. An unknown mixture containing an organic acid or base and an organic neutral compound in nearly equal amounts needs to be separated to its separate components. An understanding of solubility, extraction, crystallization and vacuum filtration is necessary in order to

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

Me and my lab partner, obtained a mixture of a un known proportion from the instructor and then flow the guide line in our lab manual to separate the mixture by applying the separation method motioned in our lab manual pages 33-40 . In this experiment, the separation methods were decantation,

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.

The objective of this extraction experiment was to achieve a comprehensive understanding, as well as master the practice, of the technique of separating various individual components of a compound.

In order to isolate benzoic acid, benzocaine and 9-fluorenone, each component needed to be separated from one another. All three compounds began together in one culture tube, dissolved in methylene chloride and formed into a homogenous mixture. In this culture tube, two milliliters of aqueous three molar hydrochloric acid was added, which immediately formed two layers, the top acidic aqueous layer was clear in color and contained benzocaine, and the bottom organic formed was yellow and contained benzoic acid and 9-fluorenone. Benzocaine’s amino group is protonated by the aqueous layer hydronium. This protonation forms the conjugate acid of benzocaine, benzocaine hydrochloride. Thus, the conjugate acid, benzocaine hydrochloride is a salt in which is soluble in water and furthermore can be isolated from the organic mixture. When testing out the pH levels in benzocaine, the pH test strip was dark blue in color, indicating a pH level of around 5 to 7. When isolating benzoic acid, two milliliters of aqueous three molar sodium hydroxide was added, which deprotonates the carboxylic group in benzoic acid, forming its conjugate base, sodium benzoate. As with benzocaine hydrochloride, sodium benzoate is a water soluble ionic salt in the aqueous layer that can then be separated from the bottom organic layer containing the 9-fluorenone. The pH test strip was a vibrant red for benzoic acid, indicating a pH of 2. Now the 9-fluorenone is left, deionized water is added to remove any excess

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

The crude product was washed by taking the reaction product in the separatory funnel and adding 23 mL of deionized H2O. The mixture was shaken and allowed to settle until layers were observable. The top layer was the desired product and approximately 25 mL of aqueous layer was extracted from the separatory funnel. Next, 25 mL of 5% NaHCO3 was added to the separatory funnel in order to neutralize the acid. This mixture was swirled, plugged with the stopper and inverted. Built-up gas was released by turning the stopcock to its opened and closed positions, releasing CO2 by-product. This was done four times in one minute intervals. The solution was allowed to settle until layers were observable. The bottom layer that contained salt, base and water was extracted from the separatory funnel. The crude product was washed again as mentioned previously.

Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water, and Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid, Methylene Chloride, and Sodium Bicarbonate Solution

Distillation is a method of separating two volatile chemicals on the basis of their differing boiling points. During this lab, students were given 30 mL of an unknown solution containing two colorless chemicals. Because the chemicals may have had a relatively close boiling point, we had to employ a fractional distillation over a simple distillation. By adding a fractionating column between the boiling flask and the condenser, we were able to separate the liquids more efficiently due to the fact that more volatile liquids tend to push towards the top of the fractionating column, thereby leaving the liquid with the lower boiling point towards the bottom. After obtaining the distillates, we utilized a gas chromatograph in order to analyze the volatile substances in the gas phase and determine their composition percentage of the initial solution. Overall, through this lab we were able to enhance our knowledge on the practical utilization of chemical theories, and thus also demonstrated technical fluency involving the equipment.

After the initial mixture has refluxed, 9.11 grams of benzophenone was dissolved in 100 mL of anhydrous ether in a beaker and was then transferred into the separatory on the reflux apparatus. This solution was then added to the Grignard reagent at a drop wise rate while stirring. After the benzophenone was added, the mixture was then refluxed for 15 minutes on a heating mantle.

In the separating funnel, a heterogeneous mixture was formed: resulting in an organic layer (top) and a solvent layer (bottom). This effectively allowed the draining of the solvent, in order to isolate the organic layer, the impure ester (1-pentyl ethanoate)

In this experiment were used three separation techniques: extraction, sublimation and recrystallization. During the first method, 0.70 g sample of salicylic acid-naphthalene mixture was dissolved in 10 ml of diethyl ether. The solution was placed in a separatory funnel and 10 ml of saturated aqueous sodium bicarbonate solution was added to it. After the initial gas was