Titration And Molarity Lab Report

4. To utilize the titration results to calculate the molarity of the hydrochloric acid and the

3. If a student did not remove all of the bubbles from inside the buret before reading the initial volume and beginning the titration, will this cause the calculated concentration of the hydrochloric acid determined from that trial to be higher or lower than the actual concentration? Explain your answer in complete

By using the pH paper to measure the solutions A through E it would point out what substance is an acid and which one was basic. Also, by adding Bromothymol blue and Phenolphthalein afterwards to the solution it would indicate what color it would turn to when mixed into an acid and a base.

Chemistry 102 is the study of kinetics – equilibrium constant. When it comes to the study of acid-base, equilibrium constant plays an important role that tells how much of the H+ ion will be released into the solution. In this lab, the method of titrimetry was performed to determine the equivalent mass and dissociation constant of an unknown weak monoprotic acid. For a monoprotic acid, it is known that pH = pKa + log (Base/Acid). When a solution has the same amount of conjugate base and bronsted lowry acid, log (Base/Acid) = 0 and pH = pKa. By recording the pH value throughout the titration process and determining the pH at half- equivalence point, the value of Ka can be easily calculated. In this experiment, the standardized NaOH solution has a concentration of 0.09834 M. The satisfactory sample size of known B was 0.2117 g. The average equivalent mass of the unknown sample was found to be 85.01 g, pKa was found to be 4.69, which was also its pH at half-equivalence point and Ka was found to be 2.0439×〖10〗^(-5). The error was 1.255% for equivalent mass and 0.11% for Ka. In other word, the experiment was very precise and accurate; the identity of the unknown sample was determined to be trans-crotonic by the method of titrimetry.

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

During a titration the pH of the solution will be monitored using a pH meter from that we get a titration curve. The titration curve is then used to determine the equivalent molecular weight and Ka value of the unknown weak acid, from that we are

The entire process was repeated once more with 1.00-mL of 6.00-M phosphoric acid and 2.00mL of

By using acid-base titration, we determined the suitability of phenolphthalein and methyl red as acid base indicators. We found that the equivalence point of the titration of hydrochloric acid with sodium hydroxide was not within the ph range of phenolphthalein's color range. The titration of acetic acid with sodium hydroxide resulted in an equivalence point out of the range of methyl red. And the titration of ammonia with hydrochloric acid had an equivalence point that was also out of the range of phenolphthalein.. The methyl red indicator and the phenolphthalein indicator were unsuitable because their pH ranges for their color changes did not cover the equivalence points of the trials in which they were used. However, the

3. A few drops of 6 M acetic acid were added until it became basic.

The purpose of this experiment was to get an understanding as to how to properly prepare chemical buffers. Also part of this experiment was to gauge the effectiveness of the buffers by measuring their pH levels in various titration solutions, using a pH meter.

For this experiment, titrations on a weak acid, acetic acid, and a buffer were performed. Acetic acid was titrated with NaOH in order to observe the half-equivalence point as well as the equivalence point. Then, the buffer and the buffered acetic acid solution prepared faced additional titration with NaOH and HCl to evaluate the differing buffering effects following the addition of a strong acid and strong base. Finally, the buffer’s buffering capacity was calculated. If the experiment were to be repeated, it would be interesting to observe the buffering effects following a titration between a weak base and a buffer instead with greater concentrations. The change in the concentration following the preparation of buffer with a weak base and its conjugate acid would pose for an interesting experiment to observe an increase in the buffering capacity.

The purpose of this lab was to determine how much acetic acid is in vinegar by using titration. Along with determining how much acetic acid is in vinegar, the titration is used to determine the molar concentration of acetic acid in vinegar. This was done by filling a buret with NaOH and then slowly dripping it into a flask (set on top of an electric stirrer) filled with 10.0 mL of vinegar and two drops of phenolphthalein indicator. Once the solution begins to turn pink that is when it is close to equilibrium. Once the solution shows any indication of turning pink, the drops should turn into drips and be very slow. It is when the solution in the flask is a barely visible pink color that it is the end point. Once the initial and final

The purpose of this experiment was to determine how much KMnO4 was needed to titrate approximately 1 mL of an Unknow X101 concentrated solution of Oxalic Acid. A standardized KMnO4 solution was used on a known solution of Oxalic acid to help determine the unknown percent oxalic acid in unknown X101. The unknown sample for this experiment was sample x101 which theoretically was a % Oxalic Acid dehydrate sample but, the average of all three trials determined it to be a 6.7% percent Oxalic acid.

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid

For this experiment, a pH meter was used so this part of the experiment began with the calibration of the pH meter with specified buffers. The buret was then filled with the standard HCl solution and a set-up for titration was prepared. 200g of the carbonate-bicarbonate solid sample was weighed and dissolved in 100 mL of distilled water. The sample solution was then transferred into a 250-ml volumetric flask and was diluted to the 250-mL mark. The flask was inverted several times for uniform mixing. A 50-mL aliquot of the sample solution was measured and placed unto a beaker. 3 drops of the phenolphthalein indicator was added to the solution in the beaker. The electrode of the pH meter was then immersed in the beaker and the solution containing the carbonate-bicarbonate mixture was titrated with the standard HCl solution to the phenolphthalein endpoint. Readings of the pH were taken at an interval of 0.5 mL addition of the titrant. After the first endpoint is obtained, 3 drops of the methyl orange was added to the same solution and was titrated with the standard acid until the formation of an orange-colored solution. Readings of the pH were also taken at 0.5 mL addition of the titrant.