Titration Lab Report

4. To utilize the titration results to calculate the molarity of the hydrochloric acid and the

Stoichiometry is a very important part of chemistry. Stoichiometry refers to calculating the masses of molecules and their products . The reactants are usually given and stoichiometry is used to find the products of the equations as well balancing the equation. An example of this would be sodium chloride (NaCl). Stoichiometry will say that if there are ten thousand atoms of sodium and one atom of chlorine, only one molecule of sodium chloride can be made and that fact can never be changed.

The purpose of this experiment is to determine an unknown concentration of acid (hydrochloric acid) with a standard solution of a base (sodium carbonate) using titration method.

(0.074 mol HCl x 1 mol NaOH) / 1 mol HCl = 0.074 mol NaOH

The results showed the molarity of the NaOH solution. This experiment was completed twice and a new average molarity

Our purpose in this lab was to create four solutions of the same components and different concentration. I found the concentration in Molarity (mol/liter). I would dilute a solution to create new solutions, using the formula M1xV1=M2xV2 where M=molarity and V=volume. In this lab, there were four solutions, Solution A, Solution B, Solution C, and Solution D. The solute or substance that dissolves was sugar and the solvent or substance that the solute dissolves in was water. For Solution A, I weighed 3.42 g sugar and diluted to 100 mL to get a concentration of 0.10 M and the color of bright red. For Solution B, I weighed 0.342 g sugar and diluted to 100 mL to get a concentration of 0.010 M and the color of pink. For Solution C, I measured 10

2. Calculate the molarity of the Hydrochloric acid in the flask. You may refer to the Titration demo at the beginning of the honors lesson, just above the Virtual Lab to see sample calculations.

Table 2: Consists of color extract taken from a red cabbage for a natural indicator. The pH reading that was measured by using the pH meter and the result of the pH reading to determine whether the solution was acidic or basic.

2. (5 pts) List and explain the names and affiliations of the various characters/stakeholders in this story – I’m looking for us to use the story to map out the complexities that are generally associated with solving public health puzzles – the stakeholders you list and explain here should apply to many of the cases we consider going forward.

ii. The second part of the titration series involves titration of NaOH with Hydrochloric acid (HCL). Again, three reps of titration and a blank titration have to be completed. A volumetric pipet is used to measure 10.00mL of HCL into three labeled conical flasks. Then the flasks are filled with deionized water until about the 50mL mark. A buret is

By using acid-base titration, we determined the suitability of phenolphthalein and methyl red as acid base indicators. We found that the equivalence point of the titration of hydrochloric acid with sodium hydroxide was not within the ph range of phenolphthalein's color range. The titration of acetic acid with sodium hydroxide resulted in an equivalence point out of the range of methyl red. And the titration of ammonia with hydrochloric acid had an equivalence point that was also out of the range of phenolphthalein.. The methyl red indicator and the phenolphthalein indicator were unsuitable because their pH ranges for their color changes did not cover the equivalence points of the trials in which they were used. However, the

First, three titration curves and three second derivative curves were created to determine the average pH at the half-equivalence point from the acetic acid titrations. Titration curves were used as visuals to portray buffer capacity. The graphs and a table, Table 1, that showcased the values collected were created and included below. The flat region, the middle part, of Figures 1, 2 and 3, showed the zone at which the addition of a base or acid did not cause changes in pH. Once surpassed, the pH increased rapidly when a small amount of base, NaOH, was added to the buffer solution. Using the figures below and

The purpose of this experiment was to determine how much KMnO4 was needed to titrate approximately 1 mL of an Unknow X101 concentrated solution of Oxalic Acid. A standardized KMnO4 solution was used on a known solution of Oxalic acid to help determine the unknown percent oxalic acid in unknown X101. The unknown sample for this experiment was sample x101 which theoretically was a % Oxalic Acid dehydrate sample but, the average of all three trials determined it to be a 6.7% percent Oxalic acid.

The purpose of this lab was to use process titration to find concentration of an aqueous solution of Hcl(aq) , using KOH(aq) as the titrant.

An acid-base titration is the determination of the concentration of an acid or base by exactly neutralizing the acid/base with an acid or base of known concentration. This allows for quantitative analysis of the concentration of an unknown acid