Transmittance Lab Report

The concentrations and absorbances of the red and blue dyes were used to find the concentration of the purple dyes. From the graph of the blue dye, the linear equation for absorbance was y = mx + b. From that formula came the equation y = 7.915 x 104 (x) + 0.02489, where y represents absorbance, m is slope, x is concentration/molarity, and b is the constant/y-intercept. The same set up was performed for the red dye, but the equation produced was y = 1.045 x 104 (x) +.001298. The equations found when graphing absorbance vs. concentration were used to find the concentration of the purple dyes. The absorbance for purple dye 3 on the red wavelength of 470 nm equaled 0.149 and 0.818 for the blue wavelength of 635 nm. For purple dye 1

From this graph and chart we can see that the higher the concentration the higher the absorbance, all the different concentrations were tested at the same wavelength (625nm). Also we can determine our unknown substances concentration by using the absorbance we got for it. The red dot on the graph followed by the line towards the horizontal axis indicates that the concentration of fast green was 34% or 5.1x10-3.

3ml of sample was taken first flask at 4 minutes and added to the appropriate tube of sodium hydroxide, from the second flask at 4.5 minute and so on, each flask was sampled at 30 second intervals. The sampling was then repeated starting at 8,12,16 minutes. The final sample from the last flask was taken at 18.5 minutes. Once the sampling was completed, measurements of absorbance were obtained for solution in each tube at 405 nm.

10 microliters of the sample is then added and the assay absorption is measured at 340nm. If absorbance was above 1.5, samples were diluted.

The ending result of this experiment confirms that as five test tubes are lined up with the varying level of absorbance, different results in the level of absorbance will appear as well, this is visible in above table. Thus, this is due to the varying amount of water in the solution. The blank sample had a 0.30 in its level of absorbance.

Scientists use an instrument called a spectrometer to quantitatively determine the amount of light absorbed by a solution. The primary inner parts of a typical spectrometer are described below. The spectrometer has a light source that emits white light containing a vast mixture of different wavelengths of electromagnetic radiation. The wavelength of interest is then selected using a monochromator (“mono” meaning one and “chromate” meaning color) and an additional exit slit. The separation of white light into different colors (wavelengths) is known as diffraction. The selected light then reaches the sample and depending on how the light interacts with the chemical compound of interest, some of the light is absorbed and some passes straight through. By comparing the amount of light entering the sample (P0) with the amount of light reaching the detector (P), the spectrometer is able to tell how much light is absorbed by the sample.

An experiment was done to determine the concentration of Allura Red in a commercially available beverage, Gatorade. This was done by using the colorimeter, the absorbance of five Allura Red solutions were measured. The graph obtained demonstrated a linear relationship and the equation obtained yielded a concentration of 1.9910-6M.

The Beers Law calibration experiment used many concentrations of crystal violet solutions. Each of these solutions were test and analyzed in order to determine the absorbance of each concentration The results were than graphed and produced a slope of 1.00E05 with an intercept of -2.21E-02.

Each stock solution was placed in a colorimeter and was tested for it Absorbance. A computer program tested and drew up the Calibration curve/linear fit equation. However, the computer could not protect potential errors. An error for determining the concentration of the diluted and undiluted, could be a skew linear fit equation. The linear fit equation could be skewed by having an inadequate ratio of the stock solution and distilled water. For example, when making stock solution 1, 0.021(L) was used instead of 0.020(L) can throw the calibration curve, resulting a skewed linear fit equation. If the “blank” was not fully clean or had left over Allura Red residue, then the “blank” was tampered with. A tampered “blank” means any comparisons with it would have a wrong Absorbance reading. However, the most likely and most effective error, is calculation. Using the wrong V1 and V2 to determine the concentration of the undiluted would affect the answer of the grams Allura Red would be consume and the amount of molecules of Allura Red. The colorimeter is adjusted to a wavelength of 470 nm is maximize the absorbance of the Allura Red. If wavelength was place at 565 nm, then Allura Red would not absorb as much color of

Our purpose in this lab was to create four solutions of the same components and different concentration. I found the concentration in Molarity (mol/liter). I would dilute a solution to create new solutions, using the formula M1xV1=M2xV2 where M=molarity and V=volume. In this lab, there were four solutions, Solution A, Solution B, Solution C, and Solution D. The solute or substance that dissolves was sugar and the solvent or substance that the solute dissolves in was water. For Solution A, I weighed 3.42 g sugar and diluted to 100 mL to get a concentration of 0.10 M and the color of bright red. For Solution B, I weighed 0.342 g sugar and diluted to 100 mL to get a concentration of 0.010 M and the color of pink. For Solution C, I measured 10

A = Absorbance difference  = Molar extinction coefficient C = Concentration L = Path length

We began by creating a blank solution of H2O to get an accurate reading for each of the solutions mixed with food coloring to understand the relationship of wavelengths to percent transmittance,

8) Steps 1 - 8 were repeated using the wavelengths of 360 nm to 900

concentration, record the absorbance readings at a fixed wavelength, and plot the absorbance vs. concentration data. The wavelength of 520 nm was selected for experiment Part

We have timed each of the three experiments for 5 minutes to make sure that our results are correct. Thanks to the program, we got the transmittance and the absorbance, together with the graph portraying our results.