Types Of Standards And Protocols In Computer Network Systems

1: Physical layer: The purpose of the physical layer is it deals with the hardware components, like cads and cables for sending and receiving data of a carrier.

Layer 3: Network - The way that the data will be sent to the recipient device is determined in this layer. Logical protocols, routing and addressing are handled here.

The fifth layer is the session layer this establishes a connection,this layer makes and sets up the connection using co ordinates and could terminate conversations links. the session layer produces services that make authentication after an interruption and not only that but it can reconnect.and as well as the transporting layer it can also have the TCP and the UDP can provide services for all most all applications.An application layer is an abstraction layer that specifies the shared protocols and interface methods used by hosts in a communications network. The application layer abstraction is used in both of the standard models of computer networking; the Internet Protocol Suite (TCP/IP) and the Open Systems Interconnection model (OSI model).Although both models use the same term for their respective highest level layer, the detailed definitions and purposes are different.In TCP/IP, the application layer contains the communications protocols and interface methods used in process-to-process communications

• “Application - The Application Layer is the layer that most network users are exposed to, and is the level at which human communication happens. HTTP, FTP, and SMTP are examples of the application layer protocols the Patton-Fuller will now be utilizing for communicating electronically” (Network Design, 2012).

1. Application (in terms of cabling infrastructure): The application layer is the OSI layer closest to the end user, which means both the OSI application layer and the user interact directly with the software application. When determining resource availability, the application layer must decide whether sufficient network or the requested communication exists.. (OSI_model#Layer_7:_application_layer)

as a device in its domain and sends the packet to the host or pushes the packet to the next

This makes sure the data transferred is in the right order, error free and reliable from beginning to end. The Network Layer is the third layer of the model and its function is to interpret the network addresses into physical addresses and figure out how to direct them from the sender to the receiver. The next layer is the Data Link Layer, this is the second layer and it separates the data it receives from the Network layer into specific frames so they can be transmitted by the Physical layer. Frames are packages for moving data, they include the raw data, the sender and receiver’s addresses, as well as error checking and control information. This makes sure the frames are delivered to their destination without any problems. The physical layer is the first layer and the lowest, the protocols at this layer recognize and receive the frames from the Data Link layer. They also monitor data error and set data transmission

The physical machines fundamental transport layer that host the GemFire and client applications and provide distribution of data between machines.

Layer 4 is the transport layer and utilises common transport protocols to enable network communications. This may include the Transport Control Protocol (TCP) and Universal Data Protocol

The internet layer is built up of four core protocols: IP, IGMP, ICMP and ARP. Internet protocol (IP) is responsible for routing, IP addressing and breakdown/reassembly of data packets, address resolution protocol (ARP) is responsible for mapping an IP address to a device on the local network, internet control message protocol (ICMP) provides diagnostic information and error reports on lost packets, internet group management protocol (IGMP) controls who receives IP datagrams in a single transmission. The transport layer is built up of two core protocols: TCP and UDP. Transmission control protocol (TCP) sequences and acknowledges packets sent and their recovery when lost in transmission allowing the computer to make and maintain network conversations where applications exchange data, defined as a connection-oriented protocol meaning the connection is maintained until the programs has finished exchanging data. User datagram protocol (UDP) This is used to transfer small amounts of data when the use of error correction isn’t needed increasing the speed of the transmission, common in multi-player video games as the user will not need to receive packets of past events in the game so the error correction featured in (TCP) would be

In general, on the internet, every packet follows 5 layers of structures (Application, Transport, Network, Data Link, and Physical). Since I have to talk about Connection-Oriented and Connectionless as a service, I will focus on the Transport layer because they are part of this layer. It allows multiple applications to use one network connection simultaneously, the layer will create ports on your computer allowing them to be reserved and used by the Application layer. Let's say that port 3600 will be used to send a message to port 80 of some other computer, whenever the port is ready to send a message, it passed on to Transport layer. In this layer, it wraps the message inside the Segment which contains some additional

27. You have installed Windows Server 2008 on a new server and want to centralize user logons and security

The application layer: this layer allows different applications to communicate with each other’s. In order to exchange different data over the network connection, the protocols included in this layer set up the standards such as DNS, HTTP, FTP. The data coded in this layer will be encapsulated to transport layer for further packing.

As the data packet moves from the upper to the lower layers, headers are _______.

Transmission Path Level: This extends between network elements that assemble and disassemble the payload of a transmission system. For end-to-end communication, the payload is end-user information. For user-to-network communication, the payload may be call-control signaling information (call setup and call termination). Cell delineation and header error-control functions are required at the end points of each transmission path.