Types of Bridges

As the conclusion, Warren truss was the strongest one out of all the three walkway design followed by the Howe truss and lastly the Pratt truss. Warren truss is mostly used in walkway construction simply because it takes less time to build this structure and also less materials are needed. This is due to the facts that, Warren truss is actually a series of isosceles triangles or equilateral triangles. In contrast to Warren truss, Howe and Pratt trusses have its diagonal members which are slanting away from the middle for Howe truss and slanting down towards the middle for Pratt truss. With this additional slanted member, the production cost are definitely higher than the cost for Warren truss.

A simple beam bridge that is flat across and supported at the two ends. A longer beam bridge can be held up along the middle by piers standing in the river. The weight of the bridge itself, plus the load that it carries, plus gravity are the downward forces are spread evenly across the length of the bridge. The upwards forces that hold the bridge up come from the piers. The Confederation Bridge in Canada is a famous beam bridge.

When bridges are poorly constructed, they may fail due to load they carry, collision by derailed trains or even by vehicles that lose control leading to catastrophic incidences. However, if bridges are well-constructed, the chances or injury are greatly minimized in the event of an accident. Discussed in the subsections are the requirements of AS 5100 standards in relation to cable-stayed bridges and include design requirements for bridges, bridge aesthetics, bridge functional requirements, bridge component design requirements and bridge construction

Initially, suspension bridges before 1940 were made of piers, towers, wires, anchorages, and roadways. Piers were the main foundation for the suspension bridges. There usually were two of them, which were made out of cement and were entrenched in ground underneath the body of water that the bridge was spanned across. Towers were built on top of the piers to provide a means of connection for the roadways and wires. Wires were connected to the towers, roadways, and anchorages to provide tension support for the weight of the bridge. The anchorages were large cement platforms that were planted into the ground on either side of the land so that the wires could be connected to it. Lastly, the roadways were the main point of the suspension bridge. They usually were wide enough to provide four lanes of traffic and stretched from one side of the bridge to the other. This was the basic design of the suspension bridges

The final primary component of a suspension bridge is the deck, or the roadway upon which cars drive and pedestrians walk. The deck is built from massive pieces of steel-reinforced concrete hoisted into the air and laid into place upon the bridge. Deck pieces are connected with bolts and rivets, then suspension cables connect each section of deck to the main

There are many differences between our bridge and other bridges. One being location. Another one being that thing that was sacrificed for it. Another one being cost. Also another difference would be weight and capacity, and the size or length.

Bridges are a vital part of people’s everyday life and without them people would not be able to do nearly as much as is possible today. The weather in the outer banks of North Carolina is very rough and can be very detrimental to the various structures on them. When hurricanes come near North Carolina the outer banks are hit the worst. Bridges on the outer banks keep being destroyed by weather and so the people there have to think about the cost, the effectiveness, and the need between a strong expensive bridge that will be able to handle rough weather or a cheap quick to build bridges that may fall with any extreme weather.

Since the early days, the men try overcome environmental challenges and, in this process, ends up creating amazing masterpieces of engineering. Among this works, the bridges appears as the clearest representatives of how the mankind could adapt to Earth’s contours. If the shape of landscape can’t be changed, the bridges are the solution to link two places and allows the connection of the traffic to improve aspects such as the communication and the trade. Depending to the need, to the sources and to the environment, the bridge can be constructed in a specific configuration. There are five main sorts of bridges configurations. First, there is the simplest bridge, the beam bridge. Second, the arch bridge, one of the oldest kind. There are the truss, composed of set of trellises. Lastly, there are the cable-stayed and

The Pratt truss bridge was originally founded by Caleb and Thomas Pratt in 1844. It is mainly used to carry trains. The biggest advantage of this bridge was its low costs for construction and the materials to construct a truss bridge are minimal. It also use materials that is cheaper and light in weight. We can easily identify a pratt truss by detecting its diagonal members, which (excluding for the very end ones) all slant down and in toward the center of the span. The pratt truss was designed by applying few laws that related to the mechanics of materials concept. The bridge is mainly built using steel girders to support the construction of the structure. The below part of bridge weight is high so, it need an enough support to prevent from

Truss bridges have been around for a long time. I see truss bridges the most out of all the different types of bridges and to me it seems like the most popular type of bridge. In addition there are thirty different types of Truss bridges which means that there is a bigger variety of Truss Bridges instead of just having one type. Truss bridges have triangular shaped beams that go all across the bridge. The bridge also is above the roadway instead of under the roadway like the arch bridge. Truss bridges could also stretch very far. The longest cantilever Truss bridge that goes is called Crescent City Connection and it is 13,418 feet long with a width of 52 feet. There is also a really long Truss bridge that is near Hoboken, the name of the bridge

These bridge variations include the simple beam bridge, truss bridges, arch bridges, suspension bridges, and cable-stayed bridges. The key differences between these bridges

According to Hecox (2011), the Tillman Bridge is 1900 ft long; also, it is 900 ft above Colorado River and has the world's tallest precast concrete columns. Its central span has 1060 ft, which is the longest single-span concrete arch of the western hemisphere. On the other hand, the St. Anthony Bridge has, according to Jones (2015), only 559 ft of lenght; which is about four times smaller than the Tillman Bridge. St. Anthony’s central span has only 305 ft, which is also very small when compared to the 1060 ft of Tillman Bridge. Another difference between the two bridges is that St. Anthony doesn’t have high elevations like the Tillman. In addition, both bridges are top-down constructed; the first one innovated using this method of construction because its elevated heights (Hecox, 2011). The second used this method because of the non-stop traffic under the bridge, and the necessity to remove the older one while building the new. However, the old bridge will not be totally discarted. A portion of the previous bridge will be used in a new interpretive plaza at the west end of the new bridge. In conclusion, both bridges have unique design features that make them very important to their

The Principle upon which all trusses rely is that the triangle is the strongest and most rigid geometric Figure. By arranging the framework of triangles in patterns that varied from designer to designer, the structure acquired different appearances and served different purposes depending on the needs of bridge builders. The pony truss, the smallest type and ordinarily confined to lengths under 140 feet, with most under 100 feet, is distinguished by its low profile and absence of bracing above the roadway. The through truss by comparison is greater in length and height and consists of a tunnel-like structure that carries traffic through a system of overhead bracing which ties together the upper chords of the bridge.

The basic design of the Tacoma Narrows Bridge itself was a suspension bridge with a center span of 2800 feet and two side spans of one 1100 feet (Farquharson, 1950, p. 17). Its two lane, reinforced concrete roadway was twenty-six feet wide with two 5 foot, 9 inch sidewalks (Farquharson, 1950, p. 19). Overall the superstructure was 5939 feet, including the suspension structures, approach spans and anchorages (Farquharson, 1950, p. 19). Anchorages were made of solid concrete and were fifty feet by 170 feet and were fifty feet high (Farquharson, 1950, p. 19). The main towers which the cables saddle were 425 feet in height and with a spacing of thirty-nine feet at the top and fifty feet at the bottom (Farquharson, 1950, p. 19). Each cable consisted of nineteen strands of galvanized wire and totaled a diameter of seventeen inches. The design of the bridge may sound rather large and structurally stable but as mentioned before the bridge was designed to be very sleek looking. By

Because of advancements in today’s technology in construction field, many types of bridges are being constructed depending on the requirement and their suitability for the situations.