. Ward Leonard method is ___________ a) Armature control method b) Field control method c) Combination of armature control method and field control method d) Totally different from armature and field control method

Q: Define initial kinetc energy.

A: Initial kinetic energy is the kinetic energy of the body at the time we consider it to study its…

Q: throttle actuator velocity v intake pipe throttle angle (aTH) slope (a) For vehicle speed control…

A: given; ⇒moving velocity =v⇒car moving with acceleration =a  ⇒lets take weight of body =w⇒normal…

Q: 1. Explain the following with neat sketch. i)vane type actuators. ii)piston type actuators

A: i) Vane type actuators Vane-type rotary actuators are shown in simplified cutaway views in figure…

Q: Explain, with suitable THREE examples, how adaptive control can be applied in monitoring the working…

A: Examples for how adaptive control can be applied in monitoring the working conditions of a milling…

Q: Which of the following is correct for a open loop system ?

A: The main problem with the open loop control system is that, it do not monitor or check the condition…

Q: ou can collec

A: A coring is designed with central open and the method is used for shown below.

Q: In which control system, output from the system has no effect on command signal? O a. Feedback less…

A: In Feedback less system, output from the system does not sent back to the controller. Therefore,…

Q: What is the effect of underdamped system?

A: The damping ratio is defined as the ration of actual damping to the critical damping. In…

Q: the following is not one of the nonmachine tool applications of numerical control.   Question 24…

A: None of the above is the correct answer

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: Robotic end-effector is comprised of two main types: i.e. gripper and end-of-arm-tool (EOAT). State…

A:

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: Explain all three fundamentals of NC technology brifly with a simple sketch.

A: NC stands for numerical control. This is a kind of automation in which machine or other processing…

Q: Which one is not called as classical controller? O a. Programmable logical controller O b. PID…

A: As, we know the most common classical controller is PID controller.

Q: Mechanism Design

A:

Q: xplain the role of feed back signal and error signal in a closed-loop control system

A: Role of Feedback system:- Feedback is taken into account to be a significant part of a closed-loop…

Q: Suggest the suitable actuator to perform the task of pick and place by the Robotics Arm. O a. Multi…

A:

Q: What is the other name of 1 × 4 Demultiplexer? And what is mean?

A: 1x4 De miltiplexer is also known as De mux which has two selection lines, one input and four…

Q: cabout 4% defecti nstruct a control cl

A:

Q: Explain Quick Return Mechanism along with commercial application

A: Generally, a rotary machine (motor) is used to create to-fro motion i.e. the rotational motion is…

Q: Hi can anyone tell me why the summation of Fx=-300sin(30)+150 instead of Fx=-300cos(30)+150?

A:

Q: 8.1 Explain the terms (a) mechanism, (b) kinematic chain.

A:

Q: Explain in details about SEQUENTIAL CONTROL SYSTEM OF Automatic Grain Store

A: Due to the advancement in the field of automation and computer technology grain handling and…

Q: An important property in mechanism analysis is the number of degrees of freedom of the linkage?…

A: A mechanism is a group of links connected to each other by joints to form a kinematic chain, where…

Q: Which type of control system is used in the given block diagram? Write the definition.

A: The Control system used in this diagram is open-loop control system.

Q: hat is the relationship of mass of block and angle of response. What can be conclude on the given…

A: we have to study the relationship between mass of block and angle of repose

Q: What is the derivative of y = 4x³ 4x³ - ²/3x² +599?

A: y = 4x3 - (2/5)x2 + 599  Derivative of y:  dy/dx = d/dx( 4x3 - (2/5)x2 +599)

Q: Which of the following is correct for a open loop system ? O a. No comparison element O b. Automatic…

A: In an open loop system,

Q: State steps that might be present in the sequential control of a dishwasher.

A:

Q: In serial manipulators, force propagates from joint to joint in the backward direction (end-effector…

A: True

Q: |5.lf the DOF is smaller than zero, all links ar mpossible to have motion. It is a ().

A: The rigid truss or frame has zero degrees of freedom and it is stable & determinate. The…

Q: Identify the control system areas of the BMS.

A: Given question: Identify the control system areas of the BMS

Q: Q. 5 (b) In what way are the stepper motors advantageous than DC and AC motors. Give application of…

A: Since you have posted a question with multiple subpart we will solve first three part for you. To…

Q: Discussion object are the same? 2- When and why will the floating object become unstable?

A: This question is based on the topic of fluid mechanics in which it discusses about stability of…

Q: 8.9 Design a mechanical system which can be used to: (a) operate a sequence of microswitches in a…

A: (a) Mechanical system used to operates a sequence of microswitches in a timed sequence is Camshaft.…

Q: Which of the following is not a criteria in determining the control system performance? natural…

A:

Q: Could you mathematically explain static forces on 3 DOF Planar Redundant Robotic…

A:

Q: ontrolling torque using Spring control method.

A: used for controlling the deflection of the pointer in measuring instruments over the scale is called…

Q: answer the question below. Robotic arms can have different end effectors. An end effector is the…

A: Solution is attached below;

Q: hat are the differences between the contact mode and the tapping mode (feedback, interaction forces,…

A: The contact mode A cantilever tip is dragged across the surface of the sample in the static contact…

Q: b. Explain 5 fundamental assumptions of a typical Primitive Machine. c. Write down induction-machine…

A: The  primitive machine has a cylindrical stator and rotor, both of which have concentric layers…

Q: Explain the robot hand grasping force control system in detail with block diagram and justify it as…

A: Robot hand grasping force : So when a robot hand want to grasp an object it requires an certain…

Q: Bohar model Gizmo answer keys

A: Niels Bohr proposed in 1913 that the unique spectral lines produced by various elements were related…

Q: w can move drone in hexacopter from one side to another side??

A: given: how can move drone in hexacopter from one side to another side??

Q: diffrenece between the Pure mechanism from Constructive mechanism. indicate the schematic diagram

A: Explanation: The pure mechanism and constructive mechanism are to types of mechanics. These…

Q: ne module.

A:

Q: n job sequencing. rule will consider a single workstation information. elect one:

A: Solution,

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.