1-Explain A case study of applications of RAMS and LCC in the Design Process?
Q: Example A sub-marine moves horizontally in sea and has its axis 15 m below the surface of water. A…
A: Pitot tube A pitot tube is a device for determining the speed of a fluid in motion (speed). In…
Q: 11. A section of a highway with length of 10 Km was evaluated using the Pavement Condition Rating…
A: In this particular problem road section with different failure have been shown in the picture We…
Q: error in the measured interior
A: Given the measured values at Stations A,B,C,D of a quadrilateral.
Q: Convert the 115/85 systolic/diastolic pressures given in millimeters of Hg to Pa .
A: To convert mmHg to Pa
Q: A four hour unit hydrograph of a catchment is triangular in shape with base of 80 hours. The area of…
A: Given data: Total depth of rainfall = 4 cm Loss = 1 mm/hr for 4 hr = 4 mm = 0.4 cm Rainfall excess =…
Q: Using examples, describe possible mistakes AND errors involved in taping measurement, discuss…
A: Taping measurement:- Tapes are used in surveying for measuring horizontal, vertical or slope…
Q: Draw the SFD and BMD for the following beam. Be sure to determine all key values, such as those at…
A:
Q: A 60 kN/m B 1.5 m с 240 kN.m 1.0 m x 150 kN/m 3.0 m 120 kN D 1.0 m E
A: This question is from solid mechanics here we are given with a simply supported beam with loadings…
Q: The centroid of the T-section shown is 2.5 inches above the base. What should be the value of b to…
A: Given A T section having centroid 2.5 inch above the base. Required Value of b
Q: Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a…
A:
Q: needs a foundation designed. Girders will be placed at 4' o.c. ith support every 8'. what weight…
A: Given:- Girders will be placed at 4' o.c. ith support every 8'. To find:- what weight will the…
Q: For the simply supported beam loaded as shown determine the slope and deflection at point(D) using…
A:
Q: 4. Bending Moment in a Beam Draw the shear and bending moment diagrams for the beam and loading…
A: Given data 1. Draw shear force and bending moment diagram. 2. Find bending moment at point D in…
Q: 5. Determine the force in members GJ, HK, IJ of the truss shown using sections b- 0.5 kip 0.6 kip 1…
A: Given : To Find : Force in the member GJ, HK and IJ.
Q: Know that all = 25.5 ksi and Tall = 14.5 ksi. 20 kips B 10 ft 2 kips/ft -30 ft с 20 kips 10 ft D
A:
Q: Determine the internal normal force, shear force, and bending moment in the beam at points B and C.…
A:
Q: Determine the Reactions of the following structures. b. Draw the Shear and Moment diagram…
A:
Q: Calculate the magnitude of TXZ at point A for the beam of cross section T. Consider the forces,…
A:
Q: Advantage of Measured or Unit rate Contract اختر أحد الخيارات a. the tender sum tells him the exact…
A: Advantage of unit rate contract: The unit rate contract makes the process of billing is simple…
Q: Through a very narrow gap of height 'h' a thin plate of large extent is pulled at a velocity V. On…
A: Given- The given situation of the question is shown below in the diagram- It is needed to find the…
Q: 10. What will be the co-efficient of passive earth pressure, at a depth of 8m in cohesion less soil…
A: Given data: Depth = 8 m Angle of internal friction, φ=30°
Q: Consider a glass tube of a 5 mm diameter is immersed vertically in water. Determine the capillary…
A: Given Diameter,d = 5 mm = 5*10^(-3) mm Surface tension of water = 0.0725 N/m Required Height of…
Q: Determine the internal normal force, shear force, and bending moment in the beam at points B and C.…
A: Internal forces in the beam The normal force-The algebraic sum of the axial forces operating on…
Q: Situation: A 3m long A36 Steel column is pinned at top and bottom. Assume E=200,000 MPa and its…
A: Given :- Length, L = 3000 mm B = 200 mm D = 100 mm Modulus of Elasticity, E = 200,000 N/mm2 For A36…
Q: An unconfined compression (UC) test was conducted on a 50-mm-diameter and 100-mm-high cylindrical…
A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…
Q: The field capacity of a soil is 25%, its permanent wilting point is 15% and specific dry unit weight…
A: Given data- Field capacity FC=25%=0.25PWP=15%=0.15depth of root zone d=80 cmunit dry weight=1.5…
Q: Determine the reactions at the supports for the structure shown
A: Given :
Q: For laminar flow in a pipe, the drop in pressure Ap is a function of the pipe length L, its diameter…
A: Given data,In a pipe having laminar flowPressure drop ∆P is a function of pipe length L,Diameter D,…
Q: The pipe assembly is subjected to a force of 600 N at B. 150 mm 150 mm 400 mm B 30 600 N 500 mm Q…
A: Given values: Force at B, FB = 600 N
Q: A circular channel (Manning's roughness, n = 0.014) with a diameter of 5 met used to convey a…
A: To find velocity of flow
Q: 9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical…
A:
Q: PROBLEM 2: The frame shown below has a fixed support at A and a pin support at C. El is constant.…
A:
Q: Design a pipe to supply water from the elevated tank to the demand point at a discharge rate of 0.05…
A:
Q: Q2: For the beam shown in Fig.(2), find the reaction forces at supports A and B respectively?…
A:
Q: A symmetric compound channel in overbank flow has a main channel with a bottom width of 30 m, side…
A: We have to calculate Value of the kinetic energy correction coefficient alpha.
Q: P5.14 The wooden pile shown in the figure has a diameter of 100 mm and subjected to a load of P =…
A: Given ; Dia of wooden pile = 100 mm P = 75kN Frictional resistance w = 3.70 kN/m Length of pile -…
Q: Calculate the chainage of TP1.
A: Given: The whole circle bearing of the line TP1 and IP is 30°. The whole circle bearing of the line…
Q: V. DATA AND TABULATION 1. Depending upon the form of the specifications for use of the material…
A: Given data:
Q: he members have E₁ = 200 GPa, ach bar from left to right are 12,
A: Given:-E1=200GPaE2=180GPaE3=169GPad1=12mmd2=20mmd3=16mmL1=900mmL2=1000mmL3=1200mmtemperature…
Q: Describe in detail the difference between a static mode imaging and a dynamic mode imaging. What is…
A: Difference Between static mode imaging and dynamic mode imaging: In static imaging a color contrast…
Q: Explain what is meant by boundary and initial conditions.
A: Whenever differential equations are given from which a unique solution is to be derived, boundary…
Q: A vertical U-tube with two legs 2 m apart is filled with water and rotated about a vertical axis 0.5…
A:
Q: The density of air at a city (such as San Diego) located at sea level is 1.225 kg⁄m3, while for a…
A: Given:- The density of air in a city (such as San Diego) located at sea level is 1.225 kg⁄m3 The…
Q: For laminar flow in a pipe, the drop in pressure Ap is a function of the pipe length L, its diameter…
A: Lets design the laminar flow in pipe , with drop in pressure per unit length. So, Drop in pressure…
Q: A steel pipe of length L=3.5m, outside diameter d₂ = 0.8m and inside diameter d: 0.6m. The inside of…
A:
Q: 5. A smooth plastic 10-m long garden hose with an inside diameter of 20 mm is used to drain a wading…
A: Given : Length of garden = 10m Inside diameter = 20mm To Find : The flow rate from pool ?
Q: Problem 3. For the simply-supported beam given below, use the Moment-Area method to determine slopes…
A:
Q: For the built-up shape shown in the figure, determine: a. The elastic section modulus considering…
A:
Q: Part A - Support Reactions Determine the support reactions for the beam shown in the figure below. 5…
A: Given :
Q: Using conjugated beam method, determine the deflection at point C (free-end of the beam shown in the…
A: Given :
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- highway laboratory Marshall Mix Design What are the elements that affect the value of flow and stability?List three primary distress modes adopted in HMA performance testing List four common HMA plant operations. List two commonly used rollers to compact an HMA layer Air voids in HMA affect durability, cohesion, and stability. Please, draw a figure illustrating this relation.Engineering design What are 2 legislation and standards of ABS plastic?