1) One mole of a van der Waals fluid with empirical constants a and b is contained within a cylinder connected to a piston. The initial volume of the gas is v, and the initial temperature of the gas is T;.The piston moves slowly so that the gas is compressed to half its volume. In this process, the temperature doubles. A reversible heat source with constant heat capacity Cand initial temperature T, is in thermal contact with the gas. a) Calculate the maximum work that can be delivered to a reversible work source in this process. b) If no work is produced, calculate the final temperature of the reversible heat source after this process takes place.

1) One mole of a van der Waals fluid with empirical constants a and b is contained within a cylinder connected to a piston. The initial volume of the gas is v, and the initial temperature of the gas is T;.The piston moves slowly so that the gas is compressed to half its volume. In this process, the temperature doubles. A reversible heat source with constant heat capacity Cand initial temperature T, is in thermal contact with the gas. a) Calculate the maximum work that can be delivered to a reversible work source in this process. b) If no work is produced, calculate the final temperature of the reversible heat source after this process takes place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air compressor is designed to compress air (assumed to 100 kPa, 20 ° C at a pressure of 1 MPa). Heat losses to the environment are considered in advance to be about 10% of the input power to the compressor. Air enters at 50 m / s where the inlet area is 90 cm ^ 2 and exits at 120 m / s through an area of 5 cm ^ 2.Determine:a) The air temperature at the outlet and the input power to the compressor.b) Heat coming out of the compressor 10% of the power
An ordinary egg can be approximated as a 5.5-cmdiameter sphere. The egg is initially at a uniform temperature of 88C and is dropped into boiling water at 97C. Taking the properties of the egg to be r = 1020 kg/m3 and cp = 3.32 kJ/kg·8C, determine (a) how much heat is transferred to the egg by the time the average temperature of the egg rises to 70C and (b) the amount of entropy generation associated with this heat transfer process.
One pound of air (consider here a perfect gas) with an initial temperature of 200F is allowed to expand without flow between pressures of 80 and 45 psia. Which of the three processes, pv=c, pv^k=c ??? pv^1.5=c will produce the maximum work with minimum heat supplied?
Steam enters the condenser of a steam power plant at 20 kPa as asaturated vapor with a mass flow rate of 20,000 kg/h. It is to be cooled by water from anearby river by circulating the water through the tubes within the condenser. To preventthermal pollution, the river water is not allowed to experience a temperature rise above10°C. If the steam is to leave the condenser as saturated liquid at 20 kPa, determine(a) the mass flow rate of the cooling water required, and(b) rate of heat loss from the steam.(c) show the process for the steam on a ?-v diagram
A 10 metric tons ice plant using ammonia refrigerant operates between evaporator and condenser temperature of -20°C and 35°C, respectively. The ice plant is to produce ice at -12°C from water at 30°C in 24 hrs. Assuming losses to be 18% of the heat absorbed from water, determine the: a.) Total amount of heat needed to absorbed by the evaporator in kW b.) Power required by the compressor in kW
Steam at 5 Mpa and 400C expands polytropically to 1.0 Mpa according to PV 1.3 = C. Determine the work of nonflow and steady flow, the heat transferred, h, and s.
Steam enters the condenser of a steam power plant at 20 kPa and aquality of 90 percent with a mass flow rate of 20,000 kg/h. It is to be cooled by water from anearby river by circulating the water through the tubes within the condenser. To preventthermal pollution, the river water is not allowed to experience a temperature rise above10°C. If the steam is to leave the condenser as saturated liquid at 20 kPa, Determine(a) the mass flow rate of the cooling water required, and(b) rate of heat loss from the steam. Please attempt (a) then (b)
5.) By traveling through a bass tube, 2.5 cm O.D. and 2.2 cm I.D., which is surrounded by steam at 55 kPa and 90% quality, 9.4 kg/s of water is heated from 15oC to 60oC. Assume the inside unit convective coefficient is 2000 W/m2-K, and the outside unit convective coefficient is 7950 W/m2-K. Determine (a) the length of tube required; (b) the steam supply in kg/h if no subcooling occurs.
1. Combustion gases enter the nozzle of a jet engine at 3.8 bar and 820 oC. Thenozzle is well insulated and the gases expand down to an exit pressure of 1.1 bar.Determine the temperature and the velocity of the gases at exit from the nozzleassuming the velocity at inlet is negligible. For the combustion gases takecp = 1.15 KJ/Kg. K and the ratio of specific heats = 1.32
Refrigerant 12 is expanded steadily in an isothermal (constant temperature) process. The flow rate is 13.6 kg/min with an inlet state of wet saturated vapor with an 80% quality to a final state of 70°C and 200 kPa. The change of kinetic energy across the device is 3.5 kJ/kg and the heat added is 21.81 kW. Determine the system power.
Liquid water at 20 oC is heated in a mixing chamber by obtaining a mixture with asaturated steam as shown in Fig. 2. As shown in this figure, the liquid water and the saturated vaporenter this chamber with mass flow rate values of 7.2 kg/s and 0.35 kg/s, respectively. On the otherhand, the mixed fluid leaves this chamber at 50 oC, as a liquid. If the ambient temperature of thesurroundings is at 15 oC, determine,a) The temperature of the saturated vapor which is entering this mixing chamber,b) The exergy destruction during this mixing process using the entropy balance,c) The exergy destruction during this mixing process using the exergy balance ,d) The second law-efficiency of this mixing chamber device, considering this ambient temperaturevalue of 15 oC.
A 2kg/s of steam expands in a turbine producing 560 kW of power output. The steam enters at a velocity of 20 m/s and exits at 75 m/s. The reduction of specific enthalpy is 410KJ/kg. Determine that the heat flow per second when the inlet of the turbine is located 950mm above the outlet.