1. A control rod AB is fixed with a pin connection at B. The rod is 26 in long and is at an angle of 600 from the positive x-axis. A 11.9 lb force F is applied to the end of the control rod (point A) down and to the right, at an angle of a from the rod. Knowing that it creates a 253.4 in lb clockwise moment about point B, determine angle a and the perpendicular distance between the line of action of force F and point B.

1. A control rod AB is fixed with a pin connection at B. The rod is 26 in long and is at an angle of 600 from the positive x-axis. A 11.9 lb force F is applied to the end of the control rod (point A) down and to the right, at an angle of a from the rod. Knowing that it creates a 253.4 in lb clockwise moment about point B, determine angle a and the perpendicular distance between the line of action of force F and point B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

NEED IN RUSH! A transmission tower is held in place by bolts at B, C, and D. If the force on the cable AD is 664 N, what is the angle of orientation with respect to the x-axis and y-axis of the wire in bolt D (θD.x and θD.y)? (degrees) Given: y = 20 m XB = XD = 2.4 m ; Xc = 8.3ZB = 4.2 m ; ZC = 2.3 m ; ZD = 10.2 m
A 2.25-kN·m torque T is applied to the solid cylinder made up of a hollow cylinder and an inner core as shown.Determine the percent of the torque carried by the inner 25-mm-diameter core.
A thin rod AB of length 1 = 600 mm is connected to a sliding sleeveon a pole. The rod rests on a C-shaped wheel located at a distancehorizontal a = 80 mm from the vertical axis of the post. Knowing that us = 0.25between the sleeve and the post, that the radius of the wheel is negligible, thatG= 100 N and 0 = 30°, determine the range of values of P ensuringthe balance of the assembly
A triangular block shown is subjected to the loads S = 1000 lb and T = 2000 lbs. If AB = 8 in and BC = 6 in, resolve each load into components normal and tangential to AC.
A uniform cable weighing 3 lb/ft is held in the position shown by a horizontal force P applied at B . Knowing that P = 180 lb and 0A= 60°, determine (a) the location of point B, (b) the length of the cable.
The outside diameter of a pulley is 0.8 m, and the cross section of its rim is as shown. Knowing that the pulley is made of steel and that the density of steel is ρ = 7.85 x 103 kg/m3, determine the mass and weight of the rim.
A control rod AB is fixed with a pin connection at B. The rod is 26 in long and is at an angle of 60 degrees from the positive x-axis. A 11.9 lb force F is applied to the end of the control rod (point A) down and to the right, at an angle of α from the rod. Knowing that it creates a 253.4 in lb clockwise moment about point B, determine angle α and the perpendicular distance between the line of action of force F and point B.
Each of the three aluminum bars shown is to be twisted through an angle of 2.1°. Knowing that b = 30 mm, τall = 50 MPa, and G = 27 GPa, determine the shortest allowable length of each bar. Refer to Table 3.1. The shortest allowable length of bar (a) is mm. The shortest allowable length of bar (b) is mm. The shortest allowable length of bar (c) is mm.
to hold the loaded wheelbarrow, our force applied to the handle is ___ the load weight 1. equal to2. more than3. in the same direction as4. less than
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 29.13 lb. Express your answer in three decimal places.
A uniform concrete slab of total weight W is to be attached as shownto two rods whose lower ends are on the same level. Determine theratio of the areas of the rods so that the slab will remain level. Answer: Aal/Ast___________________
Solve Prob. 3.43 for the position corresponding to x = 4 in. The 20-in. tube AB can slide along a horizontal rod. The ends A and B of the tube are connected by elastic cords to the fixed point C. For the position corresponding to x = 11 in., determine the angle formed by the two cords, (a) using Eq. (3.30), (b) applying the law of cosines to triangle ABC.