1. For the linkage system show, Link 1 moves along the vertical direction via a linear motor. Link 2 and 3,,dependent on the motion of Link 1, will move accordingly. Perform position analysis using Chace Mehod: (a) Draw the loop closure vectors for the problem. (b) Determine the unknowns. (c) Determine which kinematic case it is (d) Determine equations for the unknowns as function of known variables. (e) Assume link 1 is located 3 inches above the x-y coordinates, and link 2 has a length of 5 inches. Determine the numerical values of the two unknowns for this specific configuration. Link 1 Link 2 Link 3

1. For the linkage system show, Link 1 moves along the vertical direction via a linear motor. Link 2 and 3,,dependent on the motion of Link 1, will move accordingly. Perform position analysis using Chace Mehod: (a) Draw the loop closure vectors for the problem. (b) Determine the unknowns. (c) Determine which kinematic case it is (d) Determine equations for the unknowns as function of known variables. (e) Assume link 1 is located 3 inches above the x-y coordinates, and link 2 has a length of 5 inches. Determine the numerical values of the two unknowns for this specific configuration. Link 1 Link 2 Link 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A three-dimensional (spatial) manipulator of two degrees of freedom is shown in Fig. Q.1 (b). Derive link parameters and the kinematic equations for ?? ? , where B represents base or ground frame and W represents wrist frame.
For the mechanism shown below;i) Show variables on the figure,ii) Determine the space scale, ks=?iii) Write vector loop closure equation(s) by using complex numbers,iv) Solve the vector loop equation in order to determine the relative position ofpiston at point D with respect to point B when 2=60o.
Q1 A mechanical system with a rotating wheel of mass Mw (uniform mass distribution) is shown in Figure Q1. Springs and dampers are connected to wheel using a flexible cable without skip on wheel. (a) Determine all the mathematical modeling equations of the system for the translational and rotational motion. (b) Using the result in Q1(a), determine the translational motion equation in term of ? as a function of input motion ?. (c) By referring to standard second-order system form, determine the expressions for natural frequency and damping ratio of the system.
Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
The position vectors that are defined for kinematic analysis of a mechanism should form one or more kinematic loops also called?
a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the gain and T is the time constant, calculate values for µ and T for the case where the valve is at position 3. Hints: Use the constants and information in table 1. The dynamics of the water tank can be found by applying the continuity equation: qin - qout = rate of change in water tank
In Figure.4, a car wheel balancer device is used to estimate the location/direction and mass value needed to be attached to the wheel in order to statically balance it and prevent vibration during driving. Your role is to calibrate the system measurement by constructing theoretical calculation of a sample wheel and compare it with the results of the computer. The unbalanced wheel can be modelled as in Figure.5 and the four distributed point-mass as in Table.2.
What is the minimum dampening ratio for an underdamped system such that its overshoot is limited to 10%? This image is my scratch work based of an in-class problem. I'm unsure of the steps and the final equation for Zeta. It also puts out a different number that my professor wrote…
solve by the concepts of ststics
You have been provided with following types of kinematic links. Type of link Binary number = 8 Ternary number = 3 Quaternary = 2 Can you form a kinematic chain by selecting suitable number of links from the available quantity as indicated in the table above? Justify your answer.
Determine the degrees of freedom by constructing the mechanisms belonging to the given kinematic chain.
which equation is used if the system underdamped. can you pls share the whole eqn