1. The ground distance between two points is 38 km. If the distance between the same two points on a topographic map is 45 mm, determine the scale of the map.

Q: Angle Check: 101 102 103 104 Bearing Dec AZ LAT Closure : DEP Closure : Linear Error of Closure :…

A: Data given For calculation purpose the stations are named as A, B, C, D as shown in the figure.…

Q: #3 Determine the maximum deflection between the supports A and B. EI is constant. Use the method of…

A:

Q: The following figure shows a simple bracket made of structural steel with Young's modulus E = 200…

A: We will use the Finite Element method (FEM)to solve the given problem:- FEM is the numerical method…

Q: On a map with a scale of 1 cm = 290 m, the measured length of a concrete fence is 0.33m. Determine…

A:

Q: An overhead view of part of a pinball game is shown. If the plunger imparts an initial speed of 2.9…

A: The given figure is shown below:

Q: Determine the stresses in members LM, HM and CH. L x M N 0 P A H 40 k B 40 k C D 40 k 6 at 30 ft 180…

A:

Q: 7. A vertical rectangular sluice gate at the bottom of the dam is 0.60m wide and 1.8m high and…

A:

Q: 3. Draw the shear and moment diagrams for this frame. There is a roller at A and a roller guide at…

A:

Q: A crawler hoe having a 2-cy bucket and whose cost per hour is $115 (without operator) will excavate…

A: Given  Maximum digging depth= 22 ft

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: A 12 hour storm rainfall had the following depths

A:

Q: FAMILIARIZATION WTH DIFFERENT SOIL MECHANCS APPARATUS AND EQUIPMENT INTRODUCTION It is important for…

A: Introduction: Soil: It is the uppermost layer of the earth's crust that bears the constructed…

Q: Determine the smallest moment of inertia (I), if the maximum deflection of the beam is limited to…

A: Given, Maximum deflection=1/360 of span L=6 m EI=constant E=200 GPa To determine, smallest moment…

Q: Determine the intensities and of w1 and w2 of distributed loading acting on the bottom of the slab…

A: In slab AB, load in upward side is uniformly varying near edges and is uniformly distributed in the…

Q: The steel framework is used to support the 100-mm reinforced stone concrete slab that carries a…

A: Reference : Structural analysis Given :  A uniform live load of 24 kPa acting on 100 mm slab. To…

Q: Draw the shear and bending Moment Diagram of the following beam shown

A:

Q: 60 kN AQ А 6 m 40 kN 16 m B

A:

Q: 1. 820 g sample of sand was found to have the following amounts retained on each sieve. 630 μm 315…

A: Given- A sieve analysis is performed on sample of sand having total weight of 820g. After performing…

Q: The volume of irrigation water is usually expressed in acre-feet. One acre-foot is a volume of water…

A: Given: Storage capacity = 3.54 x 106 acre feet 640 acre = 1 mi2 1 acre = 43560 ft2

Q: A. Determine the x and y components of reaction at A. B. Determine the y component of reaction at B.

A: Given: F = 21 kN Free body diagram:

Q: Situation #1 El is Constant (Assume El = 1 kN-m²) Y KN -3m 1 10 + A X KN - 4 m B X= 329 Y= 29 A= 8

A: Given EI=1 KN-m2 As per first theorem of Moment area method θB/A=∫ABMEIdx Notation θB/A is the…

Q: F2-7. Determine the horizontal and vertical components of reaction at the pins A, B, and D of the…

A: To find components of reaction at point A,B,D

Q: 34-cy wheel loader will be used to load trucks from a quarry stockpile processed aggregates having a…

A:

Q: A #1 = end C of the beam. E = 200 GPa, I the moment-area theorems. a Determine the slope and the…

A: Moment area method is used to determine deflection of beams. The method used bending moment diagram…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A:

Q: A rectangular channel of 2.5 m width is carrying a discharge of 4 m³/s. Considering that…

A:

Q: A beam subjected to weather upon concrete pouring has a dimension of approximately 310 mm by 555 mm…

A: Given Beam dimensions b = 315 mm D = 555 mm Assume nominal cover = 30 mm Effective depth of beam…

Q: The split ring shown has an inner radius ₁ = 0.6 in. and a circular cross section of diameter d =…

A:

Q: A circular raft foundation of 20 m diameter and 1.6m thick is provided for a tank that applies a…

A: Given- Diameter of raft d=B=20 m, Thickness t=1.6 m, Bearing pressure q=110 kPa, Young modulus E=30…

Q: Determine the maximum upward reaction at E in kN a= 45 kN (concentrated load) b= 50 kN/m (uniformly…

A: Given data: wL=50 kN/mwd=23 kN/mP=45 kN

Q: After the population of C-City has evacuated due to regular occurrence of monsters, Saitama found…

A: Given Length of line AB=95m Bearing of line AB=S45'E Length of line AC=88m Length of line AD=43m…

Q: A. Determine the y component of reaction at A. B. Determine the x component of reaction at C. C.…

A: Given: w = 17 KN/m  Required: A. Determine the y component of reaction at A. B. Determine the x…

Q: Solve for moment and shear force diagram

A:

Q: A core cutter of 130 mm height has inner and outer diameters of 100 mm and 106 mm. respectively. The…

A: Brief introduction : The question related with Geotechnical engineering . We have to find Area ratio…

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the…

A: Given data,  V = 8.5 kN a = 32 mm bf = 65 mm tw = tf = 7 mm d = 89 mm

Q: 6-6. Determine the force in each member of the truss, and state if the members are in tension or…

A:

Q: A fluid is between two parallel horizontal plates as depicted above. The bottom plate is stationary…

A: Velocity gradient is the change in velocity per unit length/(Or height) in a fluid

Q: 1. The figure shows a pair of pin-jointed gripper-tongs holding an object weighing 2000 N. The…

A:

Q: A footing requires 4 bags of cement. if the water-cement ratio is 0.45, determine the amount of…

A:

Q: Compute the location of zero shear from support A.

A: Given: Ay = 6 KN and By = 10 KN Required: Location of zero shear from A

Q: Three parallel strip footings 3m wide each and 5m apart center to center transmit line loads of 300,…

A:

Q: Estimate the total amount of cost (Php) for concrete works (class "A") based from the following…

A:

Q: +₂ 2m 2m lokal/m

A:

Q: Determine the pressure difference ?????? ?????−???? ?????= ?(kPa) between the two pipelines.

A:

Q: The discharge from a fully penetrating well operating under steady state in a confined aquifer of 30…

A: Answer We are given Aquifer thickness = 30 m Discharge Q = 1500 litres/minutes Discharge Q =…

Q: A layer of saturated clay 5m thick is overlain by sand 4.0 m deep. The water table is 3 m below the…

A:

Q: A 2 m wide tank contains water upto a height of 0.50 m above its base. An immiscible liquid of…

A:

Q: What is the degree of kinematic indeterminacy of the truss as shown in figure?

A:

Q: 1.) It is the equivalent of 1 lumen distributed uniformly over 1 sqft of surface located 1 ft from a…

A: Lumen- How much light a bulb emits is measured in lumens. A light's lumen count indicates its…

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.