Hello can you please walk me through this problem and help me find the correct answers for number one through three Unit 32 Practical ApplicationsPRACTICAL APPLICATIONS1. You are working as a plant electrician. It is your job to install a 300-hp three-phase squirrel-cageinduction motor. The supply voltage is 480 V. The power company has determined that the maximumamount of starting current that can be permitted by any motor in the plant is 3000 A. The motornameplate is as follows:Phase: 3FLA: 352Volts: 480RPM: 1755Frame: XXXCode: LWill it be possible to start this motor across the line, or will it be necessary to use a reduced-voltagestarter to reduce starting current?2. You have been given the task of connecting a nine-lead three-phase dual-voltage motor to a 240-V line.You discover that the nameplate has been painted and you cannot see the connection diagram. To makethe proper connections, you must know if the motor stator winding is connected wye or delta. How couldyou determine this using an ohmmeter? Explain your answer.3. You are an electrician working in an industrial plant.tripping out on overload. The motor is connected to a 240-volt line. Voltage measurements indicate thefollowing voltages between the different phases: A-B = 276 volts, B-C = 221 volts, and A-C = 267 volts.Determine the percentage of heat rise in the winding with the highest current.30-hp three-phase squirrel-cage motor keepsSaveSubmit

1. You are working as a plant electrician. It is your job to install a 300-hp three-phase squirrel-cage induction motor. The supply voltage is 480 V. The power company has determined that the maximum amount of starting current that can be permitted by any motor in the plant is 3000 A. The motor nameplate is as follows: Phase: 3 FLA: 352 Volts: 480 RPM: 1755 Frame: XXX Code: L Will it be possible to start this motor across the line, or will it be necessary to use a reduced-voltage starter to reduce starting current?

1. You are working as a plant electrician. It is your job to install a 300-hp three-phase squirrel-cage induction motor. The supply voltage is 480 V. The power company has determined that the maximum amount of starting current that can be permitted by any motor in the plant is 3000 A. The motor nameplate is as follows: Phase: 3 FLA: 352 Volts: 480 RPM: 1755 Frame: XXX Code: L Will it be possible to start this motor across the line, or will it be necessary to use a reduced-voltage starter to reduce starting current?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 1PA: You are working as a plant electrician. It is your job to install a 300-hp three-phase squirrel-cage...

See similar textbooks

Similar questions

(Practical Application) #1 ) you are working as a plant electrician. It is your job to install a 300 hp three phase squirrel cage induction motor. The supply voltage is 480 V. The power company has determined that the maximum amount of starting current that can be permitted by any motor in the plant is 3000 A. The motor nameplate is as follows(photo) . Will it be possible to start this motor across the line, or will it be necessary to use a reduced voltage starter to reduce starting current?
Your assumption is that you measure Insulation Resistance [IR] using MeggerTest on an Induction Motor that works on a line voltage of 440 Volts 50 Hz with a measurable test result of 0.5 M Ohm. Question : a. What about your conclusion, is the measurement value still in accordance with the provisions of the Class Recommendation?. b. What are your actions to be able to maintain and maintain the best IR value of electric motors ?
In the distribution transformer;In the transformer used for the distribution of electricity to the houses, 3.3 kilovolts enters and 400 volts come out. When we make the phase-neutral calculation, that is, when we divide it by √3, we get 230 volts and 220 volts coming to the sockets. Where does the remaining 10 volts go? (Can you explain with figure) is this about 30 degree phase shift?
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:In a group of 3 motors, one draws 15 A the other draws 40 A, and the third 52 A. What size of the conductor in terms of ampacity may be used for the feeder circuit? 107 A 120 A 134 A 160 A
Q.7 What are the minimum allowable ampacities of the phase conductors and the neutral conductor that are to supply a 2-phase, 3-wire, 230-volt, 30-horsepower motor? Select one: A. PHASE = 69 AMPERES; NEUTRAL = 97.29 B. PHASE = 69 AMPERES; NEUTRAL = 67.29 C. PHASE = 97.29 AMPERES; NEUTRAL = 69 D. PHASE = 99 AMPERES; NEUTRAL = 97.29
A 350-HP squirrel-cage induction motor is connected to a 480-volts three-phase feeder. The nameplate lists the following: HP 350, Service factor 1.10, Full-load amps 408, NEMA Code B. The conductors are to be copper with THWN insulation, and 600:5 current transformers are used to reduce the current supplied to the overload heaters. The motor circuit is protected with dual-element time delay fuses. Determine the conductor size, overload heater size using the chart shown in Figure 34-7, the NEMA and IEC starter sizes, and the fuse size for this installation.
DEGREE: BS ELECTRICAL ENGINEERING COURSE: AC MACHINES Note: Please solve in this way. Given>Missing>Illustration>Solution>FinalAnswer. Please include symbols, units, formulas, step by step solution, please don't cut the solution. Thank you! (#16) A three-phase, 4-pole, 60-cycle, 110-volt wound rotor induction motor has its stator connected in wye and its rotor in delta. The stator and rotor windings have the same number of conductors. The rotor resistance and reactance at standstill are 0.18 ohm and 0.75 ohm respectively. If normal voltage is applied on the stator, calculate the rotor current at (A) starting, (B) when rotor speed is 1,720 rpm. [ Answer: 82.34A;15.42 A. ]
A 50 HP , 440 Volt , 3 - phase , 50 Hz Induction motor with star - connected stator winding gave the following test results : ( i ) No load test : Applied line voltage 440 V , line current 24 A , wattmeter reading 5150 and 3350 watts. ( ii ) Blocked rotor test : applied line voltage 33.6 volt , line current 65 A , wattmeter reading 2150 and 766 watts . Calculate the parameters of the equivalent circuit .
Part 2: Analysis and selection of the Wind Turbine.The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. What are the two closed loop control systems that are used generally in wind turbines? How do they work? 2. Calculate the power density of the input power from the wind when the wind is blowing at the rated wind speed at the turbine height. Clearly show your steps in details.
The data obtained in the idling test performed on a three-phase star-connected asynchronous motor; It is 1200V, 5500W, 9.5A. The data obtained in the short circuit experiment on the same motor is 250V,It is 14500W and 100A. For the case where the slip of the motor is 5%, create the approximate equivalent circuit of the motor (L type equivalent circuit), draw the equivalent circuit, find the values of the circuit elements and MUST AND MUST write them ON THE EQUIVALENT CIRCUIT. R and X values will be used in circuit elements, not Z.
DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A 4-pole, 75 kW, 3-phase, Y connected load, 50Hz 440 V synchronous motor operates at rated condition with 0.8 pf leading. The motor efficiency excluding field and stator losses is 95% and Xs = 2.5 ohms what is the machinal power developed? a. 15250 W b. 92000 W c. 78950 W d. 52446 W
DEGREE: BS ELECTRICAL ENGINEERING COURSE: AC MACHINES Note: Please solve in this way. Given>Missing>Illustration>Solution>FinalAnswer. Please include symbols, units, formulas, step by step solution, please don't cut the solution. Thank you! #09 A three-phase, y-connected induction motor has a total of 300 effective turns on its stator Determine the maximum value of the flux built up per pole when it is connected to a 220-volt, 60 cycle supply. [Ans.476,800 maxwells]