1.2Kg is on a plane inclined at 30 degrees for which uc = 0.11. The block is connected to a spring of constant K = 3.2 N / m, by a rope passing, A block of mass m = without slipping, by a pulley. The pulley is a disc of 0.8Kg and 0.14m radius. If the system is initially at rest and the spring has zero elongation, what is the block velocity modulus when the block has slid 0.25m down the inclined plane? m k=3,2 N/m 30°

1.2Kg is on a plane inclined at 30 degrees for which uc = 0.11. The block is connected to a spring of constant K = 3.2 N / m, by a rope passing, A block of mass m = without slipping, by a pulley. The pulley is a disc of 0.8Kg and 0.14m radius. If the system is initially at rest and the spring has zero elongation, what is the block velocity modulus when the block has slid 0.25m down the inclined plane? m k=3,2 N/m 30°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

A 10-lb weight stretches a spring 2 ft. If the weight is pulled down6 in. below its equilibrium position and released, find the highestpoint reached by the weight. Assume the spring–mass system residesin a medium offering a resistance of 10/√g lb times the instantaneousvelocity in feet per second
A barrel of mass 200 kg and radius 0.50 m rolls down a 40° ramp without slipping. What is the value of the friction force acting at the point of contact between the barrel and the ramp? Treat the barrel as a cylinder of uniform density.
A 0.150 kg frame, when suspended from a coil spring, stretches the spring 0.0400 m. A 0.200 kg lump of putty is dropped from rest onto the frame from a height of 30.0 cm (Fig.). Find the maximum distance the frame moves downward from its initial equilibrium position.
An object consists of a ball of weight W glued to the end of a uniform bar also of weight W. If you release it from rest, with the bar horizontal, what will its behavior be as it falls if air resistance is negligible? Will it (a) remain horizontal; (b) rotate about its center of gravity; (c) rotate about the ball; or (d) rotate so that the ball swings downward? Explain your reasoning.
PLEASE SOLVE COMPLETELY AND NEATLY!!! The shipping crate shown weighs 13kg and is initially hooked to a stretched spring (stretched length L1 = 0.8m, spring constant k = 1 kN/m, unstretched length L0 = 50 cm). The crate is released from rest at Position A, which is elevated 20 cm from the ground, after which it initially moves up the incline. The spring completely detaches from (and stops interacting with) the crate once the crate has stopped moving up the incline. Assume that the crate maintains its velocity as it transfers from the frictionless slope to the rough horizontal surface (no tumbling). Disregard the geometry of the crate. (a) Determine the work (J) done by friction if the crate makes a complete stop at Position B after travellingΔSB = 9m horizontally from point O (b) Calculate the coefficient of kinetic friction between the crate and the rough surface. (c) Find the deceleration (m/s2) experienced by the crate due to friction with the rough surface. Hint: For (b)…
In case of a single cylinder double acting steam engine, 180 kW power is being developed at a mean speed of 120 r.p.m. The coefficient of fluctuation of energy is 0.12. The fluctuation of speed is ± 2% of mean speed. The flywheel rim has mean diameter of 2 metre. The hub and spokes of the flywheel provide 8% of the rotational inertia of the flywheel. If the density of the flywheel material is 7200 kg/m3, determine the mass and cross-sectional area of the flywheel rim.
A motor vehicle of mass 1000 kg has road wheels of 600 mm rolling diameter. The total moment ofinertia of all four road wheels together with the half shafts is 10 kgm2, while that of the engine andclutch is 1 kg-m2. The engine torque is 150 N-m, the transmission efficiency is 90 per cent and thetractive resistance is constant at 500 N. Determine 1. Gear ratio between the engine and the roadwheels to give maximum acceleration on an upgrade of 1 in 20, and 2. The value of this maximumacceleration.
A uniform pole of 2.5m length and 4.0kg mass is suspended horizontally fromthe side of a building where it is affixed with a hinge. It is held in place by awire that extends from the unattached end of the pole at an angle of 53 degrees andattached firmly to the wall. A 10.0kg mass is hanging from the end of the poleas well under the influence of gravity.a. Draw a picture of the situation.b. Draw a comprehensive free body diagram showing the force on the wire,the mass, the pole, and both the horizontal and vertical forces on thehinge.c. Use the hinge as the axis of rotation and balance the vertical torques anddetermine the tension in the wire.d. Use inertial dynamics to find the horizontal and vertical forces on thehinge.
A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The rod is attached to the floor via a hinge and makes an angle of 70° relative to the ground; a massless string is also attached to the rod at the ¼ point of the rod and makes an angle of 20° relative to the horizontal. What tension must be provided by the rope so that the system remains in stationary? If at some point the string breaks, what will be the angular acceleration of the system the instant that the string breaks?
mass = 20 kg At the end of 20 complete cycles, t = 3 s, amplitude = 0.5 cm
Consider a mass-and -spring system containing two masses m1=1 and m2=1 whose displacement functions x(t) and y(t) satisfy the differential equations : x'' = -10x + 2y y'' = 3x -15y Assume that the two masses start in motion with the initial conditions x(0) =32, x'(0)=6, and y(0)=36, y'(0)=3 and are acted on by the same force F1(t)=F2(t)=-1320cos(7t). Describe the resulting motion as a superposition of oscillations at the three different frequencies. The three frequencies consist of lower, higher, and the forcing frequency. For each one please compare the magnitude of m2 to m1.
A body with a mass of m=20 kg is at rest in the vertical circular cylinder in the picture at a height h from the rigid base plate. The piece slides frictionlessly in the cylinder and hits the bottom plate under the influence of gravity g=9.81 m/s^2. The collision is completely inelastic and the bottom plate is completely rigid. The cross-sectional area of the cylinder is A=1500 mm^2, the elastic coefficient of the material is E=70 GPa and the length of the pipe is L=1.0 m. Present the responses of the system to displacement, velocity and acceleration. How high can the mass be dropped without an initial velocity so that the amplitude of the oscillation does not increase more than 1 mm?