*10-44. The shaft is made of A-36 steel. It has a diameteraf 25 mm and is supported by bearings at A and D, whichallow free rotation. Determine the angle of twist of gear Cwith respect to B.S0Nma6m30N-ma75 m0.9 m

Given, Diameter of shaft = 25 mm Radius = 12.5 mm = 12.5x 10-3 m Torque = 90 N.m

Answered: *10-44. The shaft is made of A-36…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft is made of A-36 steel. It has a diameter of 1 inches and is supported by hearing at A and D, which allow free rotation. Determine the angle of twist of gear C with respect B.
The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM. The shaft is supported on smooth bearings at B and E, which allow free rotation of the shaft. The gears C and D fixed to the shaft remove 70% and 30% of the power delivered by the motor, respectively. Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is ττallow = 12 ksi and the allowable angle of twist of D with respect to A is 0.25 degrees.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques. The shaft has a diameter of 50 mm Determine the angle of twist of end B with respect to end A.
Q: Determine the angle of twist of end B with respect to end A. Given: The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown where T=210 N⋅mT=210 N⋅m. The shaft has a diameter of 45 mm. Note: Attached in the picture is a list of wrong answers (including one from Bartleby) and im at wits end :)
The composite shaft consists of a mid-section that includes the 1-in.-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges and determine the angle of twist of end C of the shaft relative to end D.The shaft is subjected to a torque of 800 lb.ft.The material is A-36 steel.
The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of 0.125 inch. Using a rigid plate at B, it is connected to the solid 1-inch diameter shaft AB. Determine the rotation of the tube’s end C if a torque of 200lb inches is applied to the tube at this end. The end A of the shaft is fixed supported.
The motor produces a torque of T = 20 N # m on gear A. If gear C is suddenly locked so it does not turn, yet B can freely turn, determine the angle of twist of F with respect to E and F with respect to D of the L2-steel shaft, which hasan inner diameter of 30 mm and an outer diameter of 50 mm. Also, calculate the absolute maximum shear stress in the shaft. The shaft is supported on journal bearings at G at H.
A 2in diameter shaft is made of aluminum 2014-T6, and has a torque of 1/2T, -T and 2/3T respectively along its length measured from the free end with the distance of 12 inches between its section. If the factor of safety of 3 is used and the angle of twist is limited such that it does not exceed 0.1 rad. find the maximum allowable tonque T in the shaft in ksi
The 80-mm-diameter shaft is made of steel. If it is subjected to the uniform distributed torque, determine the angle of twist of end A. Take G = 75 GPa.
Determine the maximum torque that can be applied to the shaft, given that the maximum angle of twist is 0.0225 rad. Neglect bending
The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by journalbearings at C and D, which allow free rotation of the shafts along their axes. If a torque of 500 N # m is applied to the gear at E, determine the rotation of this gear.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. Determine the angle of twist of end B with respect to end A. The shaft has a diameter of 40 mm.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

*10-44. The shaft is made of A-36 steel. It has a diameter af 25 mm and is supported by bearings at A and D, which allow free rotation. Determine the angle of twist of gear C with respect to B. S0Nm a6m 30N-m a75 m 0.9 m