10.12 Refer to Figure 10.42. A strip load of q = 43 kN/m2 is applied over a width, B 11 m. Determine the increase in vertical stress at point A located z 4.6 m below the surface. Given: x 8.2 m В q load per unit area Cengage Leaming 2014

10.12 Refer to Figure 10.42. A strip load of q = 43 kN/m2 is applied over a width, B 11 m. Determine the increase in vertical stress at point A located z 4.6 m below the surface. Given: x 8.2 m В q load per unit area Cengage Leaming 2014

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Related questions

Q: The soil is having a saturated unit weight 18.0 kN/m and dry unit weight of 11 kN/m. The water table…

A: Saturated unit weight of soil = 18KN/m3 Dry unit weight of soil = 11KN/m3 Given two diagrams in Fig…

Q: Given H1 = 8.3 m., and H2 = 4.43 m. If the ground water table rises by 2.29 meters, determine the…

Q: A soil element is shown in the figure below. 128 kN/m2 32 kN/m 32 kN/m2 162 kN/m2 55 Determine the…

Q: 7. For the soil profile shown below, plot the variation of total stress, effective stress and pore…

A: Total stress in soil is load per unit area at any given plane in soil mass is either due to self…

Q: Soil Exercise The flexible area shown in Figure is uniformly loaded. Given that q = 300kN/m?…

A: Solution: Given q=300 kN/m2 Z= 3m 8 meter wide Vertical Pressure due t o a A line Load: σZ=…

Q: Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit…

A: Draw the figure.

Q: An embankment shown in the figure is constructed. Compute and plot the distributions of the vertical…

Q: A soil element is shown in Figure 10.34. Determine the following:a. Maximum and minimum principal…

Q: Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit…

A: Given data Unit weight Depth Dimensions To find Stress at point A

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 8.23). Determine…

A: Boussinesq’s formula for calculating stress below point load:

Q: Problem 6: From the figure below, given are the following; q1 = 750 Ib/ft, xı = 8 ft, x2 = 4 ft, and…

Q: Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A…

A: The embankment with sloping side show the trapezoidal load. It is necessary to calculate the…

Q: A soil element is shown in Figure 3 and 4, Determine the following: a) Maximum and minimum principal…

Q: Calculate the effective stress at A. 25 m Sand and- Gravel Water Table Unit Weight (y) = 20.72 kN/m…

A: Following is the given soil profile:

Q: Plot the variation in the effective stress (o') for the given soil profile. Plot your answer here…

Q: C 6 m B A 5 m 3 m 6 m 3 m Fiq 23 - Prob 23

Q: Question 2/ The soil profile shown in Figure (2) subjected to downward seepage calculate the…

A: Soil subdivision can be done in many ways and there are many types of soils such as clay, dust, etc.…

Q: 10.19 Refer to Figure 10.46. A flexible rectangular area is subjected to a uniformly dis- tributed…

A: Given data: q = 225 kN/m2 Total load on rectangular area = Q= q×Area=225 kN/m2×6 m×3 m=4050 kN r =…

Q: 8.10 An embankment shown in the figure is constructed. Compute and plot the distributions of the…

A: Given data z=10 m γt= 19.2 KN/m3

Q: A borehole at a site reveals the soil profile shown below. Calculate the effective stress (σ’) in…

Q: Using equation 10.35, determine the vertical stress (Aoz) increase below the center of the loaded…

A: The given data is shown below: z=2,4,6,8 and 10m

Q: Question 1: (10) For the soil profile shown below where H1 = 5 m and H2 = 5 m: a) Calculate the…

A: Solution in Dry Sandrd = G1+erw = 2.681+0.6x9.81rd = 16.431 kN/m3in ClayrSat = G+e1+e rw =…

Q: A soil profile consists of a clay layer underlain by a sand layer, as shown in Figure. If a tube is…

A: From the soil mass, the pore is present that will be made by air and water. The pressure developed…

Q: Calculate the stress distribution with depth below the center of the dam, and the stres distribution…

Q: Н.О 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: The given data is: Load at point B (QB) = 100 kN Load at point C (QC) = 200 kN Load at point D (QD)…

Q: The sand layer shown is subjected to a downward flow of water. (52.58, 0.436, 14.36) In flow 0.70 Z…

Q: For the embankment shown in Figure 10.45, determine the vertical stress increases at points A, B,…

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 6.27). Determine…

Q: Inflow Valve (open) Outflow

Q: PROBLEM 2 (15 points): The magnitude of stresses of the soil element represented by the figure below…

Q: b. Consider the downward flow of water through a layer of sand in a tank shown below. For the sand,…

Q: Problem 2: A soil element is shown 5.4 kN/m2 in the figure on the right. The magnitude of stresses…

A: Answer:- It can solve by the help of formula for major and minor principal stresses.…

Q: H.Q 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

Q: 8.10 An embankment shown in the figure is constructed. Compute and plot the distributions of the…

Q: Q.3) Determine the increase in vertical stress at a depth 4 m below point A due to surface loads…

Q: Figure below shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: Point loads of magnitude 100, 200, and 340KN act at B, C, and D, respectively (in the figure below).…

Q: 10.15 For the embankment shown in Figure 10.45, determine the vertical stress increases at points A,…

A: - Total load of embankment per meter length is, Length of base = 10+(22.5*2.25*2)=111.25 m Q=Unit…

Q: Plot the distribution of total stress, effective stress, and pore- water pressure with depth for the…

A: Following is the given soil profile: Given: For soil up to the depth of 4.5 m (A-B): Void ratio,…

Q: Refer to the figure. For a linearly increasing vertical loading on an infinite strip, given: B = 4…

A: Linearly Increasing Vertical Loading : A linearly increasing vertical loading starting from zero at…

Q: e soil profile in the figure below. Given H= 4m and H2=3m; lculate the total stress, pore water…

Q: H.Q 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: Given that: Point load at B, QB=100 kN Point load at C, QC=200 kN…

Q: An embankment shown in the figure is constructed. Compute and plot the distributions of the vertical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Problem 6 From the soil profile shown, 4.6 m Ground water table Clay e = 0.9 3.6m Gs = 2.75 1.…

A: Total stress = effective stress + neutral stress σ = σ' + u

Q: Figure P.8.12 shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: The area shown in the figure carries a uniform pressure of 200 kPa. Find the total vertical…

Q: An earth embankment is shown in Figure 10.44. Determine the stress increase at point A due to the…

A: In hydraulic engineering and flood control, embankments are used to hold water back and for flood…

Q: oblem 3: The figure shows a granular soil in a tank. The water level in the soil tank is held…

A: G=2.68 e=0.47 h=0.9m L=6m

Q: Calculate the effective stress at A. 25 m Sand and- Gravel Water Table Unit Weight (y) = 20.72 kN/m…

A: Given: The unit weight of water is 9.81 kN/m3. Consider the diagram,

Question

100%

10.12 Refer to Figure 10.42. A strip load of q = 43 kN/m2 is applied over a width,
B 11 m. Determine the increase in vertical stress at point A located z 4.6 m
below the surface. Given: x 8.2 m
В
q
load per unit area
Cengage Leaming 2014

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Refer to Figure 8.24. Determine the vertical stress increase, , at point A with the following values: q1 = 100 kN/m x1 = 3 m z = 2 m q2 = 200 kN/m x2 = 2 m FIG. 8.24 Stress at a point due to two line loads
For the same line loads given in Problem 10.8, determine the vertical stress increase, z, at a point located 4 m below the line load, q2. Refer to Figure 10.41. Determine the vertical stress increase, z, at point A with the following values: q1 = 110 kN/m, q2 = 440 kN/m, x1 = 6 m, x2 = 3 m, and z = 4 m. Figure 10.41
Refer to Figure 8.13. The magnitude of the line load q is 45 kN/m. Calculate and plot the variation of the vertical stress increase, between the limits of x = 10 m and x = +10 m, given z = 4 m. FIG. 8.13 Line load over the surface of a semiinfinite soil mass
Refer to the flexible loaded rectangular area shown in Figure 10.47. Using Eq. (10.36), determine the vertical stress increase below the center of the loaded area at depths z = 3, 6, 9, 12, and 15 m. Figure 10.47
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Use Eq. (6.14) to determine the stress increase () at z = 10 ft below the center of the area described in Problem 6.5. 6.5 Refer to Figure 6.6, which shows a flexible rectangular area. Given: B1 = 4 ft, B2 = 6 ft, L1, = 8 ft, and L2 = 10 ft. If the area is subjected to a uniform load of 3000 lb/ft2, determine the stress increase at a depth of 10 ft located immediately below point O. Figure 6.6 Stress below any point of a loaded flexible rectangular area
An earth embankment is shown in Figure 10.44. Determine the stress increase at point A due to the embankment load. Given: β = 25°, γ = 119 lb/ft 3, x = 55 ft, y = 28 ft, and z = 20 ft.
Evaluate the figure shown and solve what is being asked in the problem with the following given: e = 0.42 G = 2.8 H1 = 0.3 m H2 = 3.3 m h1 = 0.9 m z = 1.2 m a. What is the saturated unit weight of sand in kN/m³? b. Calculate the total stress at point C in kPa. c. Calculate the effective stress at point B in kPa.
11. Consider the downward flow of water through a layer of sand in the tank shown. (see picture below) Void ratio of the soil = 0.52 Specific Gravity = 2.70 Compute the value of h1. (Answer: 0.436) Compute the effective stress at A. (Answer: 17.44 kPa) Compute the effective stress at B. (Answer: 31.98 kPa) Compute the seepage force per unit volume. (Answer: 3.57 kN/m3)
Given H1 = 8.3 m., and H2 = 4.43 m. If the ground water table rises by 2.29 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.59, e = 0.61. Properties of clay: Gs = 2.74, e = 0.86. Round off to two decimal places. Answer: 13.95
Refer to the soil profile shown. Given H1 = 9.89 m., and H2 = 5.80 m. If the ground water table rises by 3.78 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.53, e = 0.63. Properties of clay: Gs = 2.75, e = 0.81