100 moles/ hr of gas containing 70% methane and 30% ethane is burned completely with 25% excess air. The gas entersthe furnace at 25°Cand the air enters hot, at 150°C No fuel exits the furnace. For the C values from Table B.2 in your text, you may usejust the a" term for simplicity Determine the adiabatic flame temperature. If 40% excessair were fed instead, explain how and why the adiabaticflame temperature would change

Question
100 moles/ hr of gas containing 70% methane and 30% ethane is burned completely with
25% excess air. The gas entersthe furnace at 25°Cand the air enters hot, at 150°C No fuel
exits the furnace. For the C values from Table B.2 in your text, you may usejust the a" term
for simplicity Determine the adiabatic flame temperature. If 40% excessair were fed
instead, explain how and why the adiabaticflame temperature would change

Image Transcription

100 moles/ hr of gas containing 70% methane and 30% ethane is burned completely with 25% excess air. The gas entersthe furnace at 25°Cand the air enters hot, at 150°C No fuel exits the furnace. For the C values from Table B.2 in your text, you may usejust the a" term for simplicity Determine the adiabatic flame temperature. If 40% excessair were fed instead, explain how and why the adiabaticflame temperature would change

Expert Answer

Want to see the step-by-step answer?

See Answer

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

See Answer
*Response times vary by subject and question complexity. Median response time is 34 minutes and may be longer for new subjects.
Tagged in

Related Chemical Engineering Q&A

Find answers to questions asked by student like you

Q: 6. The manufacture of such products as penicillin, tetracycline, vitamins, and other pharmaceuticals...

A: Part (a)The basis of the process is taken as 98 lb/hr of the feed. The symbol used for vitamins is ‘...

Q: Public concern about the increase in C0, in the atmosphere has led to many proposals to eliminate 0 ...

A: Let the basis of the calculations be 1 mole of CO2 fed to the reactor. Since there is 70% conversion...

Q: The T-x-y and P-x-y diagrams for the binary benzene-toluene system is shown below. a. The bubble po...

A: Part (a)The Antoine equation to be used is written below.Here, Pi* is the vapor pressure of the comp...

Q: A consulting firm has designed a steam system for a new process unit at your plant. Super heated ste...

A: Part (a)The diagram representing the cross section of the insulated pipe containing steam is shown b...

Q: A 2-in. schedule 40 steel pipe (ID=2.067in., OD = 2.375 in.) carries steam at 350F with a heat-trans...

A: answer:The schematic diagram of the pipe with insulation is given below with the inner radius R1, Ou...

Q: This problem is (6.30) from a book  "Thermodynamics and Statistical Mechanics An Integrated Approach...

A: The information provided in the question is as follows:Inside diameter of the hose is d1 = 5 cmNozzl...

Q: Homework #1 1.18 Nitrogen gas can be injected into oil wells to increase the recovery of crude oil (...

A: Part (a)Note: As the table 1.2 and 1.3 was not provided with the question so, conventional symbols a...

Q: 100 lbm/h of oil at 130F is needed for a process modification. The oil will be available at 70F, so ...

A: Oil is available at 70°F flowing at the rate of 130 lbm/h. It is required to heat the oil to 130°F. ...

Q: 40. A liquid mixture containing 30.0 mole% benzene (B), 25.0% toluene (T), and the balance xylene (X...

A: Part (a)The basis of the given process is taken as 100 mol/h of feed mixture.The process involves di...