100 t .01 3.00 1.02 - DRAWING CALLOUT 1.00 .03 -3.02- SHAPE OF PART FIGURE 3

Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece. Select…

A: Solution:

Q: Question 6–24 Identify a method to help avoid smudging a drawing when lettering. Refer to the…

A: As per the guidelines I am able to answer one question only. Please repost the question 6-25 again.…

Q: b) Draw Section A-A of the isometric drawing.

A: To draw Section A-A for the given isometric drawing.

Q: is this drawing metric or inch?

A: In the given drawing, the screw size is M8 x 1.25 . That means is it 8 mm nominal size screw. That…

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: F. A net 2.4 cm 4.0 cm 5.6 cm Drawing not to scale. Fnet is horizontal. F.

A:

Q: Date Class Review Activity 2-2- Study the drawing below and identify the twelve lines by name,…

A: The lines are method of understanding the CAD diagram of drafts. By observing we can identify the…

Q: rectangular form.

A: Given : ln( 1+2i)

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: 1. The . . tool is used to draw the cutting plane line arrowheads in AutoCAD .... a. spline fit b.…

A: 1)  d) polyline 2)  c) revolved 3)  b) partial 4)  b) half

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Round number to four significant figures. 156.849

A: Given: The given number is N=156.849. Rule: The number has more number than the required significant…

Q: DRAW OBLIQUE

A: Please refer the following image for the Oblique view of the given isometric view.

Q: I need answers to this part, thank you.

A: Monodetail Drawing:A monodetail drawing describes single part. This drawing is used for maximum…

Q: determine the overall fraction of the operation.

A: In a two stage wire drawing operation,   the fractional reduction in the first stage is = 0.4…

Q: A mandrel or steel rod is used to produce in drawing process.

A: Solution:

Q: Identify the lines

A: Answers: 1.Phantom line 2.Section line 3.Hidden line 4.Cutting plane line 5.Leader line 6.Hidden…

Q: 1- Redraw the isometric drawing. 2- Add all center lines. 3- Add all necessary dimensions.

A:

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: Fill the blanks correctly and define

A: Given: For apinion of 15 teeth,where, Pinion is usually a two meshed gears. It is used in several…

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: 10)A moving mandrel is used in Wire drawing Tube drawing Metal cutting Forging

A: As per given question  We have to choose correct options and explain

Q: 150* 6. The component above requires equally spaced slots 2-1/2" apart over a 150" span. How many…

A:

Q: The minimum possible thickness

A: Given; A thick sheet having 4 mm is rolled with 300 mm diamaterOr, d=300 mm t=4 mmFriction…

Q: Thickness of the sheet produced in a single pass.

A: Given data; Thickness, t=6 mmDiameter,D=200 mmGiven is diameter rolls to reduce thickness without…

Q: Draw the front, Top , and side planes for a complete cut *Note the shape is symmetrical

A: a. Front b. Side c. Top

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: Create an oblique drawing

A:

Q: Round number to four significant figures. 156.899

A: To round of given figure to four significant figures count four digits from left and check if fifth…

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of     Primary shaping process

Q: Question: A circular shape blank will be cut of (100 + ) mm diameter from a strip of (2.8 + N mm…

A:

Q: The main shaft of an engine that drives the rice mill line shaft drives a 24 inches flat pulley  on…

A:

Q: LATHE A 40,000 5,000 2,000 LATHE B 56,000 7,000 2,800 3.5 First Cost Salvage Value Annual…

A: Machine Parts that shows both are equally economical  Let Part be P  AW of A = AW of B= First…

Q: Match the following. Shaping operation is an example of Bending is an example of

A: Shaping operation is an example of Answer: Primary shaping operation

Q: and fill out the blanks:

A: we have to name the different parts of a CNC lathe

Q: The thickness of the blank

A: Given; Determine thickness of the blank needed to produce; by power spinning a missile cone of…

Q: N= 11 %3D Question: A circular shape blank will be cut of (100 + mm diameter from a strip of (2.8 +…

A:

Q: How did 6650 mm2 come from please show the work.

A:

Q: n section views, match patterns should be drawn parallel to one of the edges of the part. True?…

A: In section views, match patterns should be drawn parallel to one of the edges of the part. True?…

Q: 1. Would the part shown in Figure 2 below 'pass inspection'? Yes No _ .062+.004 DRAWING CALLOUT .065…

A: Here, dimension of part is given as 0.062±0.004 which means upper limit is 0.062+0.004=0.066 and…

Q: a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm…

A: According to the details provided in the question, we need to DRAW the figure.  i am using the…

Q: Reduction ratio in the first and subsequent draws may not The minimum number of draws necessary will…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.