Answered: 105.5-g sample of a metal was placed…

105.5-g sample of a metal was placed into water in a graduated cylinder, and it completely submerged. The water level rose from 25.4 mL to 37.2 mL. Use data in Table 1.1 to identify the metal.

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter1: Introduction To Chemistry

Section: Chapter Questions

Problem 1.89PAE: 1.89 Imagine that you place a cork measuring 1.30cm4.50cm3.00cm in a pan of water. On top of this...

See similar textbooks

Related questions

Q: Use significant figures to express the inherent uncertainty in measured quantities and in…

A: The uncertainty in a measurement is an estimate of the amount by which the measurement result may…

Q: A chemistry student weighs out 0.0977 g of acetic acid (HCH,CO,) into a 250. mL volumetric flask and…

Q: A scientist has two solutions, which she has labeled Solution A and Solution B. Each contains salt.…

A: Given : concentration by % of solution A = 60 % Concentration by % of solution B = 85 %.…

Q: When a 1.271g Tums tablet reacted with 44.485 mL of hydrochloric acid (density: 1.140 g/mL), carbon…

Q: A student poured 4.6 mL of water into a test tube. She marked the level of the water on the test…

A: A) option is correct

Q: Mercury metal is poured into a graduated cylinder to exactly 22.5 mL. The mercury used to fill the…

A: Given information: Volume = 22.5 mL Mass of empty graduated cylinder = 12.0 g Mass of mercury +…

Q: A chemistry student weighs out 0.0353 g of acetic acid (HCH,CO,) into a 250. mL volumetric flask and…

Q: The rate at which water falls at the Niagara Falls is about 84,760 ft3/s. How many liters of water…

Q: A chemistry student weighs out 0.166 g of chloroacetic acid (HCH, CICO,) into a 250. mL volumetric…

A: Chloric acetic acid reacts with sodium hydroxide to form sodium chloroacetate and water. The…

Q: A student performs an experiment to determine the density of a sugar solution. She obtains the…

A: A data is said to be precise if experimental values are close to each other. A data is said to be…

Q: If you report two measurements of mass, 7.42 g and 7.56 g, are the measurements accurate? Are they…

A: If the average values of different measurements are close to correct value, the measurement is…

Q: Gold is a very soft metal that can be hammered into extremely thin sheets known as gold leaf. If a…

A: The average thickness of the sheet produced from given grams of gold is calculated as shown below

Q: Create a properly labelled and formatted scientific table of data for the relevant measurements…

A: The data given is, 1) Mass of empty beaker = 50.45 g. 2) Mass of beaker and water = 81.26 g. 3) Mass…

Q: The density of aluminum is 2.70 g/cm3. The mass of a solid piece of aluminum is 3.32 g. What is its…

Q: A thin sheet of nickel measured 5.00 cm by 7.00 cm was found to weigh 0.350 g. If the density of…

A: Given : Mass of Nickel sheet = 0.350 g Length of sheet = 5.00 cm Width of sheet = 7.00 cm

Q: A chemist must prepare 500. mL of 1.00 M aqueous barium chlorate (Ba(Cl03),) working solution. He'll…

A: From the provided stock solution of 1.22M Barium chlorate solution, 500mL of 1M aqueous barium…

Q: A student dissolved 230.8 grams of cesium chloride in 100.0 grams of 90 °C water. The student then…

A: 43.8 g of substance has separated out as solid. The mass of cesium chloride present in dissolved…

Q: A chemist adds 125.0 mL of a 2.9 x 10 'M mercury(I) chloride (Hg, Cl,) solution to a reaction flask.…

A: Given Molarity of Hg2Cl2 solution = 2.9 * 10-7 MVolume of Hg2Cl2 solution = 125.0 mL1 L = 1000 mL…

Q: The solubility of potassium chromate is 66.9 g per 100 g of water. In an experiment, a student had…

A: The question is based on the concept of solubility. We have to calculate how much solute can be…

Q: Your 50 mL beaker has a mass of 6.51 g. You add 10.00 mL to the 50 mL beaker and now the total mass…

A: Given, 50 mL beaker has a mass of 6.51 g. You add 10.00 mL to the 50 mL beaker and now the total…

Q: The speed of light in a vacuum is 2.998*108 m/s. What is its speed in kilometers per hour (km/h)?

A: It is given that speed of light in vacuum is = 2.998×108 m/s

Q: 4)1345 dm in to Km? 5) 780 ounces in to Kg?

Q: A chemist adds 125.0 mL of a 2.9 x 10 'M mercury(I) chloride (Hg,Cl,) solution to a reaction flask.…

A: For Hg2Cl2 Solution : Volume = 125 mL = 0.125 L Molarity = 2.9 × 10-7 M…

Q: What is the volume (in units of m^3) and density (in units of g/mL) of a 325g rectangular block of…

Q: The density of manganese is 7.21 g/mL, that of calcium chloride is 2.15 g/mL, and that of sodium…

A: Given: The density of manganese = 7.21 g/mL The density of calcium chloride = 2.15 g/mL The density…

Q: A 75 g sample of sodium chloride (table salt) is to be produced by evaporating to dryness a quantity…

A: NaCl = 3.5 % by mass % by mass = Mass ofsolutemass of sea water solution×1003.5 % = M1 g×100M =…

Q: A chemistry student weighs out 0.0310 g of phosphoric acid (H, PO,), a triprotic acid, into a 250.…

A: Given values-> Weight of H3PO4 = 0.0310 gm Volume of H3PO4 = 250 ml Molarity of NaOH= 0.1900 M

Q: mi/hr

Q: How can you tell what numbers are exact, and which are measured? For example, one mile, one meter,…

A: Exact numbers cannot be simplified and have an infinite number of significant figures. Measured…

Q: A prescription requires an 4.82 mL injection of a 1:100 solution of a drug. The pharmacy only…

Q: At what temperature would 250 mL of water boil? 1000 mL? Is the boiling point an intensive or…

A: The temperature at which a substance in liquid state changes into a gas is called boiling point. The…

Q: A chemistry student weighs out 0.0665 g of sulfurous acid (H,So,), a diprotic acid, into a 250. mL…

A: The detailed solution of your question given below-- Since, we know that if number of moles constant…

Q: What is the Volume of 9.86 x 10^-2 pounds 7.90 g/mL steal ( hint use the determined density of steal…

A: Given data, Density of steel = 7.90 g/mL 1 pound = 453.6 g Mass of steel = 9.86 x 10-2 pounds =…

Q: A 109.35 g sample of brass is added to a 100-mL graduated cylinder with 55.5 mL of water initially…

A: According to the archimedes principle, the volume of water displaced when a solid is added in it is…

Q: 1. The student obtains 15 g of an unknown substance. 2. The student notes that at room temperature…

A: Extensive properties are the properties that depends upon the amount of matter in a sample

Q: A piece of metal ore Weights 5.00 g. When a student places it into a granduated cylinder containing…

A: Density of substance= Mass of substanceVolume of substanceGiven mass of metal ore = 5.00 g

Q: 1. (8 pts) The density of diamond is 3.51 g/cm'. The international (but non-SI) unit for weighing…

A: This question is based on unit conversion: Density= Mass/Volume 1carat=200mg 1cm=10mm

Q: A block of lead has dimensions of 4.5 cm by 5.2 cm by 6 cm. The block weighs 1587 g. From this…

Q: The density of titanium is 4.54 g/mL. What is the volume, in milliliters, of 163 g of titanium?

Q: II) Density a) What is the mass of a rectangular piece of aluminum 160.6 cm × 140.8 cm × 15.2 cm?…

A: • Density=massvolume• mass = clensity×volume• volume of rectangle = l×b×h…

Q: 5. A technologist collected the following data for their Class A volumetric flask: Table 1:…

Q: A 500 mL bottle of water contains 100 ppm of calcium. The recommended daily intake of calcium for…

Q: 16) 164.0 g of a substance occupy a volume of 120.0 mL. In relation to water, which statement is…

Q: A chemistry student weighs out 0.0623 g of acrylic acid (HCH,CHCO,) into a 250. mL volumetric flask…

A: Given: The mass of acrylic acid added to 250 mL of the volumetric flask is 0.0623 g. The molarity of…

Q: A sample of tap water contains 1.95 x 103 ppm CaCO3(aq). Assuming the density of tap water is…

Q: A chemist must prepare 150. mL of 1.00 M aqueous iron(II) bromide (FeBr,) working solution. He'll do…

A: The concentration (M) of any solution can be expressed as follows: Concentration (M) = Number of…

Q: A chemistry student weighs out 0.167 g of phosphoric acid (H,PO), a triprotic acid, into a 250. mL…

A: H3PO4 + 3NaOH -----> Na3PO4 + 3H2O So, Number of moles of NaOH = 3 x number of moles of…

Q: A lead ball is added to a graduated cylinder containing 20.3 mL20.3 mL of water, causing the level…

A: The volume of the ball will be the volume of the water displaced.

Q: If your piper uses 89 drops of stearic acid/hexane solution to add 1.28 mL to a graduated cylinder…

Concept explainers

Matter and Measurement

In the universe, there is matter, energy, and void space. The universe contains energy and void space. The definition of matter can be considered as something which possesses mass and consumes space. Chemistry is that branch of science which deals with the study of matter. Under chemistry, nature, composition, and the changes occurring to matter are discussed.

Question

100%

105.5-g sample of a metal was placed into water in a graduated cylinder, and it completely submerged. The water level rose from 25.4 mL to 37.2 mL. Use data in Table 1.1 to identify the metal.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

1.87 A solution of ethanol in water has a volume of 54.2 mL and a mass of 49.6 g. what information would you need to look up and how would you determine the percentage of ethanol in this solution?
1.89 Imagine that you place a cork measuring 1.30cm4.50cm3.00cm in a pan of water. On top of this cork, you place a small cube of lead measuring 1.15 cm on a side. Describe how you would determine if the combination of the cork and lead cube will still float in the water. Note any information you would need to look up to answer the question.
The density of a solution of sulfuric acid is 1.285 g/cm3, and it is 38.08% acid by mass. Calculate the volume of the acid solution (in mL) you need to supply 125 g of sulfuric acid.
Gold leaf, which is used for many decorative purposes, is made by hammering pure gold into very thin sheets. Assuming that a sheet of gold leaf is 1.27 105 cm thick, how many square feet of gold leaf could be obtained from 28.35 g gold? The density of gold is 19.3 g/cm3.
Exactly 1 liter of a solution contains 31.4 grams of a certain dissolved substance. What mass in grams is in exactly 2 liters? How about 7.37 liters? Express the results in the proper number of significant figures.
The label on a bale of mulch indicates a volume of 1.45 ft3. The label also states that the mulch in the bale will cover an area of a garden 6 ft 6 ft to a depth of 1 in. Account for the discrepancy in the given volumes.
A student dissolved 230.8 grams of cesium chloride in 100.0 grams of 90 °C water. The student then cooled that solution to 20 °C . That cooled solution formed a solid (or "precipitate"), and after separating and drying this solid the student found that the solid weighed 43.8 grams. What is the solubility of cesium chloride in water at 20 °C ? < calculate your answer as grams of cesium chloride per 100 grams of water, but DO NOT include your units in your answer>
The density of manganese is 7.21 g/mL, that of calcium chloride is 2.15 g/mL, and that of sodium acetate is 1.528 g/mL. You place these three solids in a liquid, in which they are not soluble. The liquid has a density of 2.15 g/mL. Which will sink to the bottom, which will stay on top, and which will stay in the middle of the liquid?
Your 50 mL beaker has a mass of 6.51 g. You add 10.00 mL to the 50 mL beaker and now the total mass is 16.81 g. What is the density of the solution in g/mL?
A sample of tap water contains 1.95 x 103 ppm CaCO3(aq). Assuming the density of tap water is 1.00g/mL, calculate the mass of CaCO3 in 2.00 L of water.
During their lifetime, a person will consume approximately 1.2 × 104 gallons of water. An Olympic-size swimming pool, which has a volume of 2.5 million liters (L), can provide a lifetime of water for how many people? Recall that 1 gallon (gal) = 3.785 × 10-3 m3, and 1 mL = 10-6 m3
The density of manganese is 7.21 g/mL, that of calcium chloride is 2.15 g/mL, and that of sodium acetate is 1.528 g/mL. You place these three solids in a liquid, in which they are not soluble. The liquid has a density of 2.15 g/mL. Which will sink to the bottom, which will stay on the top, and which will float in the middle of the liquid?