11- Find X(0.5), X(3), x(2) by division, and x(5) by partial fraction forX(z)=(2z²-3z)(z-1)(z-2)with ROC z>2.If the ROC |z|< 1, determine x(-3).

Answered: Image /qna-images/answer/0021e1bb-f8a5-42ce-8215-a6ab8f42e32e.jpg

Answered: 11- Find X(0.5), X(3), x(2) by…

11- Find X(0.5), X(3), x(2) by division, and x(5) by partial fraction for (2z²-3z) X(z)= with ROC z>2. (z-1)(z-2) If the ROC |z|< 1, determine x(-3).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 4- Find the z transform of the following functions: (a) x₁(n)= (-1)"2"u(n) (b) x2 (n) = na"…

A: Given Data:To Find:Z transform

Q: How does a serial in/parallel out register become serial in/serial out?

A: Serial in/parallel out:- The SIPO register is filled with serial information a single bit at a…

Q: 3.39 Use Laplace transformation to determine the mesh currents I(s) and 1(s) in Figure 3.36. Let v…

A: In problem 3.37 the value of the resistor is missing,The circuit diagrams,

Q: (a) The NMOS transistor in the source-follower circuit of Fig. P7.122(a) has gm = 10 mA/V and a…

A: Given Data:An NMOS source-follower circuit with,Transconductance andLarger small-signal output…

Q: Figure 1 shows a potentiometer used to measure the displacement and velocity of an elevator. The…

Q: 0.5 F 0.5m(t) A 10 ΔΙΩ 아날 FIGURE 3.33 For Problem 3.36.

A: Given circuit:To determine:Expression for i0(t)

Q: 10- Find the sequences for the following z-transform z² z² + 4 (a) X(z) = |z| > 2, (b) X(z) = Z…

Q: Binary data is transmitted using ASK through a channel that adds AWGN with power spectral density…

A: here we have to find the amplitude of the received carrier signal.

Q: + . 4Η 10 Ω 40 Ω Μ 2Ω 1100 V Figure 5 t=0 2Η

Q: Charge Q 8.0x10" C is distributed uniformly throughout a spherical insulating shell of radius R =…

A: The charge is given, Q= Radius,r==

Q: 1) The load on a 460 V, 60 Hz, Y-connected, balanced three-phase source consists of three equal…

A: I have written this solution as handwritten solution. Hope you find the perfect solution.

Q: Tow Conducting SPherical Shells have radial a=3, b = 6 cm The int cior is a perfect dircted for…

A: Given data, ,To find outWe have to determine the capacitance value for and when for and for .

Q: Design the following circuit so that the operating point is at the center of the load line, keep the…

A: In this questionWe need to determine the value of Rc1 and R2 as shown the circuit. We knowVBE ON =…

Q: autotransformer

A: A single phase transformer rating48KVA, 480/240 V Now 2winding transformer changed to auto…

Q: Ex: In Cylindrical Coordinates Let Pv=o P<\mm pv=2 sin (2000xP) n</m³ 1mm <p <1-5. Find for D…

A: A hollow cylinder which a charge density as a function of distance.

Q: Q5. Plot the root loci for the closed-loop control system with Equation 1 and Plot the root loci for…

A: Plot the root loci for the closed-loop control system with equation (1),.

Q: Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and…

Q: Power Flow Analysis 0.01 +0.03 Slack Bus V₁ = 1.05/0° 3 0.02 + j0.04 0.0125+j0.025 138.6 45.2 MW…

A: Given,A three-bus system having,Bus 1 (slack bus) with voltage Bus 2 (load bus) with Bus 3 (load…

Q: Given the information appearing in Figure 3, determine B. 20 ΜΑ R8 Vec 2.7 ΚΩ + B VCE = 7.3 V -2.1 V…

A: Given that fixed bias circuit is base current…

Q: Find i, in the circuit in (Figure 1), given that ig = 1.2 mA. Assume the op amp is ideal. Express…

A: For the given operational amplifier circuit, the current io needs to be calculated and the same can…

Q: A lossless transmission line with Z. = 500 is 30 m long and operates at 2 MHz. The line is…

A: ZL=60+j40 ohm is load impedance Z0 =50 ohm is characteristic impedanceFrequrncy,f=2Mhzu=0.6C

Q: Determine the output Vo1. Write your answer in millivolts. 20 mV 6.8k 68kQ 10kn Vol 100kΩ Voz

A: Circuit diagram is given as,

Q: 2. Reduce the block diagram shown in the figure to a single transfer function, T(s) = C(s)/R(s).…

A: In this questionWe need to determine the transfer function of the given system. We are solving this…

Q: A diesel station supplies the following loads to various consumers: Industrial consumer = 1500 kW;…

A: It is given that:Industrial consumer=1500 kW;Commercial establishment = 750 kW;Domestic power = 100…

Q: Determine all possible signals that can have the following z-transforms. 1 1- 1.52-¹ +0.5%-² (a)…

Q: Consider the signal x(n) = [−1, 2, -3, 2, −1] ↑ with Fourier transform X(w). Compute the following…

A: Given dataSigna, To find outWe have to determine the , , , and

Q: 2) Calculate the total current (IT)? î o 14V 15 kHz C1 H 0.1μF C2 0.047μF R1 47052 R2 33052 C3…

A: It is given that:

Q: 6. Given the relaxation oscillator of Fig. 17.68: a. Find RB1 and RB2 at IE = O A. b. Determine Vp,…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: calculate the natural linewidth of this emission

Q: A- A 10 kHz signal wanted to be sent and encrypted using FHSS with a factor of 10, if Af-5KHz…

A: FHSS stands for Frequency Hopping spread spectrum. It is a wireless communication technique where…

Q: Find the equivalent resistance in the following circuit. 12V A B D 4Ω 15Ω 7.4Ω Μ 10.4Ω 5Ω ΕΩ 40.

Q: Find (a)V1 and (b)V, in the circuit in the figure using nodal analysis. 1 mA (a) (b) + 8 mA V 4 ΚΩ +…

Q: A 10-MVA 4.6-kV 60-Hz 6-pole three-phase synchronous generator has armature resistance of 2 ohms and…

Q: 1- Determine the magnitude and phase response of the following system (a) y(n) = [x(n) + x(n-1)] (b)…

A: The given systems are as follows,We have to determine the magnitude and phase response of the…

Q: (B) A waveform d(t)=40sin(450t+35°) +40, is to be sampled periodically and reproduced from these…

A: Given: A waveformis to be sampled periodically and reproduced from its samples successfully.To find…

Q: Q1.4 Determine v₁. Q1.5 Determine io. 24 +)2A {10Ω 310H t = 0 1.25 Η + HU t = 0 το 36H 7.5 ΚΩΣ

A: The given circuit diagram is shown below,

Q: 5 A discrete-time system can be (1) Static or dynamic (2) Linear or nonlinear (3) Time invariant or…

A: (1) Static or dynamic system: A static system has an output that depends only on the current input,…

Q: SIM 7.118 The NMOS transistor in the CS amplifier shown in Fig. P7.118 has V₁ = 0.7 V and V₁ = 50 V.…

A: Given dataTo find outWe have to determine the voltage at the drain, , and the corresponding…

Q: Et 0.21. V0₁-0.2 |v2=0.2 Voz=0.2 Ik 24- 27 2K + 2k ли 2K 8k 2K- Yx YZ 10k миск 20k lok uy

A: The response of the circuit needs to be obtained and the same can be obtained by analysing the…

Q: Example 2: a 3-phase SM its armature resistance is 0.50 and syn. Reactance is 0.86692/phase. The…

Q: Simplify the circuit above.

A: The given circuit needs to be reduced to get the required simplified circuit and the simplified…

Q: A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200…

A: In this question we have to find the new generation output for G1.

Q: For battery operated high voltage insect killer (i.e. bug zapper) used at home: (a) Summarize types…

A: A battery-operated high-voltage insect killer, also known as a bug zapper, is a portable device used…

Q: 12. For the VII characteristic shown in Fig. A, calculate the resistance of the load. V(V) 60 40 20…

A: We need to find the resistance of the load?

Q: 1- Determine the resistance spreads for 3-bit D/A convertor for binary weighted resistor and for the…

Q: Given the information appearing in Figure 2, determine Vce. 470 ΚΩ B =90 +22 V 9.1 ΚΩ Ic Figure 2…

Q: A single-phase load consumes 10 kW at 0.9 power factor lagging from a distributed generation (DG)…

A: Load 1: Power of load 1 Power factor ( lagging ).Rated voltage V = 220 V.Load 2 :Power consumed…

Q: There is a parallel plate capacitor. The gap between the two conducting plates is filled with a…

A: Given:When the gap between two conducting plates is filled with a vacuum the capacitor capacitance…

Q: In the circuit in (Figure 1) the voltage and current expressions are v=60e-25t V, t>0; i= 20e-25 mA,…

A: Voltage expression,and the current expression,

Q: 58-kVA, star-connected, 448 V, 3-phase, 50-Hz alternator, the effective armature resistance is 0.625…

Concept explainers

Electric field

A physical field present around an electrically charged particle that exerts a force on all other charged particles is called an electric field. The charged particles present in the field either repel or attract. From electric charges or time-varying magnetic fields, the electric field originates. One of the manifestations of electromagnetic force which is one of the four fundamental forces present in nature are the electric fields and magnetic fields.

Question

11- Find X(0.5), X(3), x(2) by division, and x(5) by partial fraction for
X(z)=
(2z²-3z)
(z-1)(z-2)
with ROC z>2.
If the ROC |z|< 1, determine x(-3).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Case(i) If ROC |z|>2.

VIEW

Step 3: Case(ii):- If ROC |z|<1.

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

given signal x(n) has point in coordinates: (-3,0), (-2,0), (-1,1), (0,1), (1,1), (2,0), (3,0) calculate all the coordinates of y(n) = x(1/2n+1) and draw.
G(s) = (s+1)/(s(s+3) a) Draw the contour C in the s-plane for which you will draw the Nyquist plot of G(s). If there is a pole of G(s) at s = 0, draw the contour as looping around to the right of this pole (so that the pole is not enclosed by the contour). B) Write G(jω) in the form ?(??) = ?(?) + ??(?).
Given that D= (10r3/4 ) ar (c/m2) in cylindrical coordinates, evaluate both sides of the divergence theorem for the volume enclosed by r = 1m, r =2m and Ƶ= 0 and Ƶ= 10
Derive the
1.) Find the distance from a transmit antenna (gain = 27 dB) with 10 Watt input power at which the power density is 5 mW/m². Assume free-space propagation. 2.) The power density is 4 mW/m² at some distance R from an isotropic antenna. The isotropic antenna is replaced with a different antenna and the power density measured is now 60 mW/m² at the same distance R. What is the gain (in dB) of the second antenna? 3.) The received power at an airplane is calculated as Pr=-43 dBm at a range of 13 miles using free-space propagation. Determine the received power (in dBm) at a range of 52 miles. Step by step and easy to understand and clear please. thanks
Let V = 2x * y ^ 2 * z ^ 3 and epsilon= epsilon o . Given point P(l, 2, - 1) , find: (a) V at point P: (b) overline E at point P: (c) rho v at pint P; (d) the equation of the equipotential surface passing through point P; (e) Does V satisfy Laplace's eq uation?
Question: An AM radio signal propagating in free space has: E = Eo sin(1200πt - βz)ax H= (Eo / η)*sin(1200πt - βz)az detrmine β and η such that the fields Satisfy <<Maxwell’s equations>>. >>you must use Maxwell’s equations to Satisfy!!!!
Which row represent the most stable system and why? nyquist and root locus plot attached.
1. State or name one example of wired transmission media. 2. A type of transmission line that is highly susceptible to atmospheric noise due to being unbounded. 3. Name or State one physical law that Maxwell's Equations were based upon 4. True or False: EM waves can travels faster in physically bounded media like wires as compared to free-space propagation
Use Routh-Hurwitz method, how many roots are on the left-half plane by the polynomial equation 3 0 2 4
Given that D = 10sinϴar + 2 cosϴaϴ .Evaluate both sides of the divergence theorem for the volume enclosed by the shell r = 2.
Compute the syndrome vector for the received vector r = [11001] and hence find