13-10. A wood pipe having an inner diameter of 0.9m 0.9 is bound together using steel hoops each having a cross- sectional area of 125 mm. If the allowable stress for the hoops is o = 84 MPa, determine their maximum spacing s along the section of pipe so that the pipe can resist an in- ternal gauge pressure of 28 kPa. Assume cach hoop supports the pressure loading acting along the length s of the pipe. 28 kPa 28 kPa

Question
13-10. A wood pipe having an inner diameter of 0.9m
0.9
is bound together using steel hoops each having a cross-
sectional area of 125 mm. If the allowable stress for the
hoops is o = 84 MPa, determine their maximum spacing
s along the section of pipe so that the pipe can resist an in-
ternal gauge pressure of 28 kPa. Assume cach hoop supports
the pressure loading acting along the length s of the pipe.
28 kPa
28 kPa
Expand
Transcribed Image Text

13-10. A wood pipe having an inner diameter of 0.9m 0.9 is bound together using steel hoops each having a cross- sectional area of 125 mm. If the allowable stress for the hoops is o = 84 MPa, determine their maximum spacing s along the section of pipe so that the pipe can resist an in- ternal gauge pressure of 28 kPa. Assume cach hoop supports the pressure loading acting along the length s of the pipe. 28 kPa 28 kPa

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Classical Mechanics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: Air in an ideal Diesel cycle is compressed from 2 to 0.13 L, and then it expands during the constant...

A: Given: The volume of the air in an ideal diesel cycle before compression is V1=2 L The volume of the...

Q: Refrigerant-22 absorbs heat from a cooled space at 50°F as it flows through an evaporator of a refri...

A: Given data: *The temperature at which the refrigerant R22 absorb heat from cooled space is T1=50°F *...

Q: Distinguish between elastic buckling and inelastic buckling?

A: Buckling refers to a condition of failure of columns when the axial load on columns cause it to defl...

Q: Cortical bone is decidedly anisotropic in its fracture behavior. Crack propagation parallel to the l...

A: A crack is most likely to develop along with the weak interface parallel to the long axis of the bon...

Q: Consider a TV set that consumes 120 W of electric power when it is on and is kept on for an average ...

A: Given: The average time per day TV is kept on is t=6 h The power consumes by the TV is P=120 W The u...

Q: Please help me with this question, the question asks to find force FAB and FAC.

A: Consider the diagram shown below. Here,

Q: The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 201...

A: Given data Two rods AB and CD are made with A 36 steel and 2014 36 Aluminium alloy Inital temperatur...

Q: F15–10. The spring is fixed to block A and block B is pressed against the spring. If the spring is c...

A: Given Data: The mass of block A is MA = 10 kg. The mass of block is MB = 15 kg. The spring constant...

Q: Two identical hockey pucks are moving on a hockey rink at the same speed of 3 m/s and in perpendicul...

A: By using principle of impulse momentum For puck A (in Y direction) For puck B (in Y direction) Fo...

Q: Why is work done a scalar quantity?

A: Physical work is obtained as dot product of force and displacement. Since force and displacement are...

Q: The jib crane supports a load of 750 lb from the trolly which rides on the top of the jib. Determine...

A: Click to see the answer

Q: How The product pressure × volume has energy units.

A: Step 1: Write the units SI units of pressure and volume.

Q: oil has a spc.gravity of 0.94 with dynamic visc. of U=0.0096 N.sm/^2 flows in a 90 mm diamater pipe ...

A: Given that, Calculating the velocity of the oil inside the pipe,    

Q: A thin-walled cylinder of a high-strength aluminumalloy (KIC = 24 MPa √m ) has the following dimensi...

A: Write the given data.

Q: A pump is designed to deliver 9500 L/min of water at a required head of 8 m. The pump shaft rotates ...

A: Calculations

Q: The 40-kg gymnast drops from her maximum height of h = 0.5 m straight down to the bar as shown. Her ...

A: The mass of the gymnast, m = 40 kg The maximum height of the bar, h = 0.5 m The center of mass, y = ...

Q: The aluminum rod BC (G= 26 GPa) is bonded to the brass rod AB(G= 39 GPa). Knowing that each rod is s...

A: Given data: *The torque on the rod is T=100 Nm. *The diameter of the aluminium and brass rod is d=12...

Q: *R17-8. The W200 × 46 wide-flange A992-steel column can be considered pinned at its top and fixed at...

A: Write the properties of A992 steel. Write the properties of the W200X46 flange.

Q: Two reservoirs, which differ in surface elevation by 40 m,are connected by 350 m of new pipe of diam...

A: Write the given Data:

Q: Two bolts at A and B are tightened by applying the forces and couples shown. Replace the two wrenche...

A: Given Two bolts Bolt A is tighten with 220 lb.in Bolt B is tighten with 238 lb.in To find The result...

Q: How are the modulus of rigidity & Young's modulus related?

A: Given E = Modulus of elasticity/ Young modulus G = Modulus of rigidity To find The relationship betw...

Q: A man raises a 10-kg joist with a length of 4 m by pulling on a rope.Find the tension T in the rope ...

A: Given Data: The mass of the joist is M = 10 kg. The length of the joist is L = 4 m. The tension in ...

Q: Four tugboats are bringing an ocean liner to its pier. Each tugboat exertsa 5000-lb force in the dir...

A: Given: The force exerts by tugboats, F = 5000 lb (a) The free body diagram for the tug boats is give...

Q: The water needs of a small farm are to be met by pumping water from a well that can supply water con...

A: The data given is, Discharge, Q = 4 L/s Pipe dia, D = 5 cm = 0.05 m Dyanmic viscosity, ? = 0.00131 ...

Q: *14-20. The crash cushion for a highway barrier consists of a nest of barrels filled with an impact-...

A:  

Q: Please help me with this question, thank you.

A: Click to see the answer

Q: Portions of a 1/2 x 1/2 -in. square bar have been bent to form the two machine components shown. Kno...

A: Given Data: The coss-sectional area of the squer bar is: 0.5 X 0.5 in2. The allowable stress is : σ...

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When fu...

A: Draw the temperature variation along the pipe.

Q: The temperature difference between the hot and cold fluids in a heat exchanger is given to be ∆? at ...

A: The symbols representing the temperature difference in the hot and cold fluids at each end are not w...

Q: Poisson's ratio is defined as:

A: Click to see the answer

Q: For the area indicated, determine the orientation of the principal axes at the origin and the corres...

A: Draw the diagram of the section.

Q: The isentropic efficiency of a nozzle is defined as the ratio of the actual kinetic energy of the fl...

A: The isentropic process is the process in which entropy of the fluid remains constant. The isentropic...

Q: Describe the variation of gage pressure with depth in the gradient zone of the solar pond.

A: Solar ponds are basically the small artificial lakes that have some measurable depths. They are pool...

Q: When a 20-lb weight is suspended from a spring, the spring is stretched a distance of 4 in. Determin...

A: Calculate the stiffness of the spring by using the relation for force in a spring. Here, F is the f...

Q: 18-5. A force of P = 20 N is applied to the cable, which causes the 175-kg reel to turn since it is ...

A: The data given is, Force applied on cable, P = 20 kN Mass of the reel, MG = 175 kg The radius of gy...

Q: A large vertical dam in the shape of a symmetric trapezoid has a height of 30 m, a width of 20 m at ...

A: Given data:   The height of the symmetric trapezoid is: h = 30 m. The width of the symmetric trapezo...

Q: Determine whether the force-and-couple system shown can be reduced to a single equivalent force R . ...

A: First reduced the given force system to a force -couple at the origin. And net force would be,  

Q: What happens when a shaft having a circular cross-section is subjected to a torque?

A: When the torque is subjected to the shaft, the shear stress is generated in the shaft, and this gene...

Q: A rectangular plate 125 mm long, 10 mm wide, and 3 mm thick is formed from fused silica (aka fused q...

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: A bolt located 50 mm from the center of an automobile wheel is tightened by applying the couple show...

A: Given data: Distance from the centre, d = 50 mm Time, t = 0.10 s Mass of wheel, m = 19 kg Radius of ...

Q: A bar with surface temperature (310) oC and diameter (9.5) mm, temperature 20oC and heat convectionI...

A: Given data