Answered: #15. A high-speed drill rotating…

#15. A high-speed drill rotating counter clock wise at 2400 [rpm] comes to a stop in 2.5 [s]. a) what is the drill's angular acceleration? b) how many revolutions does it make before it stops?

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter7: Rotational Motion And The Law Of Gravity

Section: Chapter Questions

Problem 5WUE

See similar textbooks

Similar questions

Math Review (a) Convert 47.0 to radians, using the appropriate conversion ratio. (b) Convert 2.35 rad to degrees. (c) If a circle has radius 1.70 m, what is the are length subtended by a 47.0 angle? (See Sections 1.5 and 7.1.)
A child rolls a marble on a bent track that is 100 cm long as shown in Figure P2.8. We use x to represent the position of the marble along the track. On the horizontal sections from x = 0 to x = 20 cm and from x = 40 cm to x = 60 cm, the marble rolls with constant speed. On the sloping sections, the marbles speed changes steadily. At the places where the slope changes, the marble stays on the track and does not undergo any sudden changes in speed. The child gives the marble some initial speed at x = 0 and t = 0 and then watches it roll to x = 90 cm, where it turns around, eventually returning to x = 0 with the same speed with which the child released it. Prepare graphs of x versus t, vx versus t, and ax versus t, vertically aligned with their time axes identical, to show the motion of the marble. You will not be able to place numbers other than zero on the horizontal axis or on the velocity or acceleration axes, but show the correct graph shapes. Figure P2.8
A disk 8.00 cm in radius rotates at a constant rate of 1 200 rev/min about its central axis. Determine (a) its angular speed in radians per second, (b) the tangential speed at a point 3.00 cm from its center, (c) the radial acceleration of a point on the rim, and (d) the total distance a point on the rim moves in 2.00 s.
A flea is at point on a horizontal turntable, 10.0 cm from the center. The turntable is rotating at 33.3 rev/min in the clockwise direction. The flea jumps straight up to a height of 5.00 cm. At takeoff, it gives itself no horizontal velocity relative to the turntable. The Ilea lands on the turntable at point . Choose the origin of coor-dinates to be at the center of the turntable and the positive xaxis passing through at the moment of takeoff. Then the original position of the flea is 10.0i cm. (a) Kind die position of point when die Ilea lands. (b) Find die position of point when the flea lands.
A merry-go-round is stationary. A clog is running around the merry-go-round on the ground just outside its circumference, moving with a constant angular speed of 0.750 rad/s. The dog does not change his pace when he sees what he has been looking for: a bone resting on the edge of the merry-go-round one- third of a revolution in front of him. At the instant the dog sees the bone (t = 0), the merry-go-round begins to move in the direction the dog is running, with a constant angular acceleration of 0.015 0 rad/s2. (a) At what time will the dog first reach the bone? (b) The confused dog keeps running and passes the bone. How long after the merry-go-round starts to turn do the dog and the bone draw even with each other for the second time?
Figure P10.18 shows the drive train of a bicycle that has wheels 67.3 cm in diameter and pedal cranks 17.5 cm long. The cyclist pedals at a steady cadence of 76.0 rev/min. The chain engages with a from sprocket 15.2 cm in diameter and a rear sprocket 7.00 cm in diameter. Calculate (a) the speed of a link of the chain relative to the bicycle frame, (b) the angular speed of the bicycle wheels, and (c) the speed of the bicycle relative to the road, (d) What pieces of data, if any, are not necessary for the calculations?
Consider two cylinders that start down identical inclines from rest except that one is frictionless. Thus one cylinder rolls without slipping, while the other slides frictionlessly without rolling. They both travel a sh01t distance at the bottom and then start up another incline. (a) Show that they both reach the same height on the other incline, and that this height is equal to their original height. (b) Find the ratio of the time the rolling cylinder takes to reach the height on the second incline to the time the sliding cylinder takes to reach the height on the second incline. (c) Explain why the time for the rolling motion is greater than that for the sliding motion.
An object of mass 680 g, tied to a string of length 1.5 m, is rotating at a constant speed of 25 m/s. Determine the period of rotation. 3.8s 2.6s 0.6s 1.7s Please I need a surely answer and a quicker response
A drill, at its highest speed, rotates at 4000 rpm. If the drill takes 0.700 s to go from rest to full speed, how many revolutions does it make in that time? a) 1.40×103 revb) 293 revc) 23.3 revd) 147 rev
An object of mass 680 g, tied to a string of length 1.5 m, is rotating at a constant speed of 25 m/s. Determine the period of rotation. 3.8s 2.6s 0.6s 1.7s Please I need a quicker response
14. A wheel on a moving car slows uniformly from 70rad/s to 42 rad/s in 4.2 seconds. How many revolutions was made by the wheel? a. 50 rev b. 67 rev c. 37 rev d. 54 rev
In a traditional wall mounted clock, the second hand makes one revolution in 60.00 s. The length of the second hand is found to be 6 cm. What is the speed of the end of the second hand? What will be the speed at a point midway on the second hand?