15-105. The two blocks A and B each have a mass of 400 g. The blocks are fixed to the horizontal rods, and their initial velocity along the circular path is 2 m/s. If a couple moment of M = (0.6) N m is applied about CD of the frame, determine the speed of the blocks when t=3s The mass of the frame is negligible, and it is free to rotate about CD. Neglect the size of the blocks. M = 0.6 N · m 0.3 m- 0.3 m

15-105. The two blocks A and B each have a mass of 400 g. The blocks are fixed to the horizontal rods, and their initial velocity along the circular path is 2 m/s. If a couple moment of M = (0.6) N m is applied about CD of the frame, determine the speed of the blocks when t=3s The mass of the frame is negligible, and it is free to rotate about CD. Neglect the size of the blocks. M = 0.6 N · m 0.3 m- 0.3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from rest
18-37 The spool has a mass of 20 kg and a radius of gyration of = 160 mm. if the 15 kg block A is released from rest, determine the velocity of the block when it descends 600 mm.
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
17-74 The two blocks A and B have a mass Ma and Mb, respectively, where Ma > Mb. If the pulley can be treated as a disk of mass M, determine the acceleration of block A. Neglect the mass of the cord and any slipping on the pulley.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
18-19 The 30 kg disk is originally at rest, and spring is unstretched. A couple moment M= 80 Nm is then applied to the disk as shown. Determine how far the center of mass of the disk travels along the plane before it momentarily stops. The disk rolls without slipping.
17-59 The uniform slender rod has a mass m. If it is released from rest when = 0, determine the magnitude of the reactive force exerted on it by pin B when = 90.
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The 5-kg collar has a velocity of 7 m/s to the right when it is at A. It then travels along the smooth guide. Determine its speed when its center reaches point B. The spring has an unstretched length of 150 mm and B is located just before the end of the curved portion of the rod
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
The disk, which has a mass of 40 kg, is subjected to the couple moment of M = (2θ + 6) N m, where θ is in radians. If it starts from rest, determine its angular velocity when it has made two and a half revolutions.
The smooth surface of the vertical cam is defined in part by the curve r =(0.2 cos θ + 0.3) m. The forked rod is rotating with an angular acceleration of 2rad/s^2, and when θ = 45° the angular velocity is 6 rad/s. Determine the force the camand the rod exert on the 2-kg roller at this instant. The attached spring has a stiffnessk = 100 N/m and an unstretched length of 0.1 m.