Answered: 17-5. Determine the radius of gyration…

17-5. Determine the radius of gyration k, of the body. The specific weight of the material is %3D y° = x %3D 2 in. to sinst ta2 abecip 8 in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.75P

See similar textbooks

Related questions

Q: 17-2. The solid cylinder has an outer radius R, height h, and is made from a material having a…

A: Consider a cylindrical element of mass dm and radius dr The mass of the cylindrical element will be…

Q: This is a dynamics problem. Answer: kO = 2.17 m

A: The radius of gyration is the square root of the ratio of moment of inertia and mass. Thus, for…

Q: *17-8. The hemisphere is formed by rotating the shaded area around the y axis. Determine the moment…

A: Given A Hemisphere Total mass = m Density = ρ To find Determine the moment of inertia Iy

Q: *18-8. The double pulley consists of two parts that are attached to one another. It has a weight of…

A: Given Data: The weight of the pulley be WP = 50 lbs The radius of gyration of the pulley is K = 0.6…

Q: kinelic enorgy ol tro hoop it gium y: the hoop. Then, Cakulale the 1oling down without slipping an…

A: As per the guidelines we are subjected to solve only one question at a time please repost the same…

Q: 17-23. Determine the moment of inertia of the overhung crank about the x' axis. The material is…

A: Step 1: The density of steel is ρ = 7.85 Mg/m3 = 7.85 x 103 kg/m3 The length between the xx’ is…

Q: 17-17. Determine the location y of the center of mass G of the assembly and then calculate the…

Q: 17-18. Determine the moment of inertia of the assembly about an axis perpendicular to the page and…

A: Given data: *The mass of the block is m=3 kg. *The mass of the semi cylinder is mc=5 kg. *The radius…

Q: *17-16. Determine the mass moment of inertia of the thin plate about an axis perpendicular to the…

A: Given Data: The radius of the circular plate is r = 200 mm. The side of the square hole in the…

Q: 21-15. Determine the moment of inertia of both the 1.5-kg rod and 4-kg disk about the z' axis. 300…

Q: 21-69. The top has a mass of 90 g, a center of mass at G, and a radius of gyration k = 18 mm about…

A: Write the given data:

Q: The device acts as a pop-up barrier to prevent the passage of a vehicle. It consists of a 100-kg…

A: Given data: mp=100 kgmb=240 kg Need to determine the moment of inertia of the plate and block about…

Q: *17-4. The paraboloid is formed by revolving the shaded area around the x axis. Determine the radius…

Q: 17-11. The assembly is made of the slender rods that have a mass per unit length of 3 kg/m.…

A: Consider the following figure. Calculate the mass part AB. Calculate the mass of part CD.

Q: If W=35 kN/m, and L 6 m, determine the slop at 2.5 m from E=210 GN/m2 and the moment of inertia, I…

Q: 17-19. Determine the moment of inertia of the wheel about an axis which is perpendicular to the page…

Q: *21-68. The conical top has a mass of 0.8 kg, and the moments of inertia are 1, = 1, = 3.5(10-3) kg…

Q: The pendulum consists of a 8-kg circular disk A, a 2-kg circular disk B, and a 4-kg slender rod.…

A: The calculation is done perpendicular to the page so it is taken as the z-axis. So polar moment of…

Q: Determine the velacity of the block affer it has fallen 5ft. in feet per Second Weight of block =…

A: Given data: The mass of the block is, m=260 lbs. The value of spring constant is, k=30 lb/ft.…

Q: The pendulum consists of a 8-kg circular plate and a 3-kg slender rod. Determine the radius of…

Q: 17-1. Determine the moment of inertia 1, for the slender rod. The rod's density p and…

A: Given Mass of the rod = m Length of the rod = l Cross-sectional area = A Rod density = ρ To find…

Q: 17-6. The sphere is formed by revolving the shaded area around the x axis. Determine the moment of…

A: Draw the schematic diagram for the above system and consider a small element dx. Consider the shell…

Q: 17-46. The drop gate at the end of the trailer has a mass of 1.25 Mg and mass center at G. If it is…

A: Given data Mass of drop gate, M = 1.25 Mg. Draw the free body diagram and the kinetic diagram for…

Q: If the frictional moment at the pivot O is 7 N-m in the clockwise direction, determine the tensions…

Q: 17-10. The pendulum consists of a 4-kg circular plate and a 2-kg slender rod. Determine the radius…

A: Given Data: The mass of the slender rod is Mr = 2 kg. The mass of the circular plate is Mc = 4 kg.…

Q: *21-20. Determine the moment of inertia of the disk about the axis of shaft AB. The disk has a mass…

A: Given data, Mass of the disk, m=15 kg Radius of the shaft, R=150 mm

Q: 17-7. The frustum is formed by rotating the shaded area around the x axis. Determine the moment of…

A: Given : The density of the frustum material is ρ. The total mass of the frustum is m. The major…

Q: *21-4. Determine the moments of inertia I, and I, of the paraboloid of revolution. The mass of the…

A: Given Mass of paraboloid = 20 slug To find Moment of inertia About x axis About y axis

Q: *21-16. The bent rod has a mass of 3 kg/m. Determine the moment of inertia of the rod about the 0-a…

A: Given data The mass of rod, m = 3 kg/m. The bent rod is subdivided into three segments and the…

Q: The motorcycle has a kerb mass of 239 kg and test rider's mass was recorded as 76.35 kg. The wheels…

Q: If the shaft is located at a desired point of the load, and d1 = 0.1 m, d2 = 0.05 m, D = 0.04 m, a =…

A: Given Diameter of gear 1 = 0.1 m Diameter of gear 2 = 0.05 m Diameter of cylinder = 0.04 m Griper…

Q: The double pulley consists of two wheels which are attached to one another and turn at the same…

A: Given:mass of pulley, m=25 kgradius of gyration, k=110 mm,mass of block A, ma=40 kgmass of…

Q: 17-21. The pendulum consists of the 3-kg slender rod and the 5-kg thin plate. Determine the location…

A: Given that, Mass of the slender rod, mr=3 kg,Mass of the thin plate, mp=5 kg, The Center of mass is…

Q: 21-19. Determine the moment of inertia of the composite body about the aa axis. The cylinder weighs…

A: Given data: d=2 fth=2 ftmcylinder=20 lbmhemi-sphere=10 lb

Q: Specifically a dynamics problem. Question in pic below. Answer: omega = 20.35 rad/s

A: Write the expression of the kinetic energy of weight A. Write the expression of the kinetic energy…

Q: The uniform 60 kg slender rod is at rest in the position shown when P = 600 N is applied. Determine…

Q: *17-68. The device acts as a pop-up barrier to prevent the passage of a vehicle. It consists of a…

A: Given data as per the question weight of steel plate =100 kg weight of concrete block = 200 kg

Q: The Shaft Shown m nhe Araure below Cawies tuso makses at C cnd D m the Same axial Plane but…

Q: The wheel has a weight of 24 lb and a radius of gyration kg = 0.4 ft.

Q: 21-17. The bent rod has a weight of 1.5 lb/ft. Locate the center of gravity G(I, ỹ) and determine…

A: The weight density is given as γ = 1.5 lb/ft a= 1 ft and b= ft On substitution, we get x' = 0.667…

Q: 18–17. The center O of the thin ring of mass m is given an angular velocity of wg. If the ring rolls…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: *21-44. The uniform plate has a mass of m = 2 kg and is given a rotation of w = 4 rad/s about its…

A: Given, Mass of rectangular plate, Angular velocity of the plate, Breadth of the rectangular plate,…

Q: The pendulum consists of a 4-kg circular plate and a 2-kg slender rod. Determine the radius of…

A: Since the pendulum is hinged about point O. Then this pendulum will rotate about O. Calculate the…

Q: *21-12. Determine the moment of inertia I of the composite plate assembly. The plates have a…

A: Draw the schematic diagram of the assembly.

Q: 21-2. Determine the moment of inertia of the cone with respect to a vertical ỹ axis passing through…

A: Consider the diagram shown below for the elemental mass.

Q: R19-4. The wheel having a mass of 100 kg and a radius of gyration about the z axis of k, = 300 mm,…

A: Given : The mass of wheel = 100 kg The radius of gyration = 0.3 m The radius of the wheel = 400 mm=…

Q: 17-5. Determine the radius of gyration k, of the body. The specific weight of the material is y =…

A: Given data: The specific weight of the material is γ=380 lbft3 A small element on the body is as…

Q: The Part A compound disk pulley If it has a mass of 3 kgkg and a radius of gyration consists of a…

A: M=3kg ma=mb=1kg

Q: *18–16. A motor supplies a constant torque M = 6 kN • m to the winding drum that operates the…

A: Free body diagram of the figure,

Q: *17-16. The two steel channels are to be laced together to form a 9-m-long bridge column assumed to…

A: Moment of inertia of the whole section about the x axis is Iwx=2Ix=221.60×106=43.20×106 mm4 Moment…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

This is a dynamics problem.

Answer: k_x = 1.2 in

17-5. Determine the radius of gyration k, of the body. The
specific weight of the material is
%3D
y° = x
%3D
2 in.
to
sinst
ta2 abecip
8 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the mass of the R-134a.
Determine the moment of inertial about an axis perpendicular to the page and passing through the pin at O. The thin plate has a hole in its center. Its thickness is 50 mm and the material has a density of ρ = 50 kg/m^3
he assembly consists of a disk having a mass of 5 kg and slender rods ABand DC which have a mass of 2 kg/m. If L = 0.6 m, determine the moment of inertia and radius of gyration of the assembly about an axis perpendicular to the page and passing through point O. Also, find the position of the center of mass Gin relation to O. Please explain steps
A) Determine the position of the center of gravity of the figure's structure. B)Determine the moment of inertia of mass with respect to the x' axis that passes through the structure's center of gravity and is parallel to the x axis. The cone has a density of 600 kg/m3 and the cylinder a density of 800 kg/m3. Consider H = 83
The pendulum consists of two rods AB and OC, which have a mass density of 3kg/m. The thin disk has a mass of 12 kg/m2. Determine the location of the center of mass of the pendulum, calculate the mass moment of inertia about the axis perpendicular to the sheet and passing through point O. Report only the moment of inertia in terms of [kg m2].
The pendulum consists of two rods AB and OC, which have a mass density of 3kg/m. The thin disk has a mass of 12 kg/m2. Determine the location of the center of mass of the pendulum, calculate the mass moment of inertia about the axis perpendicular to the sheet and passing through point G. Report only the moment of inertia in terms of [kg m2].
The pendulum consists of a 6.5- kg circular plate and a 2.5- kg slender rod. Determine the radius of gyration of the pendulum about an axis perpendicular to the page and passing through point O.
The 150-kg pendulum has a center of mass at G and a radius of gyration about G of kG = 0.25m, as shown in Figure 2. Determine the horizontal and vertical components of reaction on thebeam by the pin A and the normal reaction of the roller B at horizontal direction when thependulum is rotating at 5 rad/s. Neglect the weight of the beam and the support. If the normalreaction of the roller B at horizontal direction change to vertical direction, determine thehorizontal and vertical components of reaction on the beam by the pin A.
Solve Prob. 7.29 if =0.
The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If the drum begins rotating slowly counterclockwise, determine how far the plank will travel before it comes to rest again. (Note: Because the drum rotates slowly, the inertia of the plank may be neglected.)
The passengers, the ship and the structure have a total mass of 73 Tons, their center of mass in G, and a radius of gyration with respect to B of kB = 3.5 m. Additionally, the 3-ton steel block at point A can be considered as a point of concentrated mass. If the ship rotates freely at 9.3 rad/s when it reaches the lowest point, as shown in the figure, determine the moment of inertia of the system about pivot B (in kgm2) The angular acceleration for the position shown (in rad/s2) is: The vertical reaction at pivot B (in N) is: The horizontal reaction at pivot B (in N) is:
Determine the moment of inertia of the thin plate about an axis perpendicular to the page and passing through the pin at O. The plate has a hole in its center. Its thickness is 50 mm and the material has a density of 50 kg/m^3