18-41. The spool has a mass of 20 kg and a radius ofgyration of ko = 160 mm. If the 15-kg block A is releasedfrom rest, determine the distance the block must fall inorder for the spool to have an angular velocity w = 8 rad/s.Also, what is the tension in the cord while the block is inmotion? Neglect the mass of the cord.200 mm

Given that: The mass of the spool m=20 kg. The radius of gyration is K0=160 mm The angular velocity…

Answered: 18-41. The spool has a mass of 20 kg…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18-37 The spool has a mass of 20 kg and a radius of gyration of = 160 mm. if the 15 kg block A is released from rest, determine the velocity of the block when it descends 600 mm.
18-19 The 30 kg disk is originally at rest, and spring is unstretched. A couple moment M= 80 Nm is then applied to the disk as shown. Determine how far the center of mass of the disk travels along the plane before it momentarily stops. The disk rolls without slipping.
17-95 The 20 kg punching bag has a radius of gyration about its center of mass G of kG = 0.4 m. If it is initially at rest and is subjected to a horizontal force F = 30 N, determine the initial angular acceleration of the bag and the tension in the supporting cable AB.
17-74 The two blocks A and B have a mass Ma and Mb, respectively, where Ma > Mb. If the pulley can be treated as a disk of mass M, determine the acceleration of block A. Neglect the mass of the cord and any slipping on the pulley.
15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from rest
17-59 The uniform slender rod has a mass m. If it is released from rest when = 0, determine the magnitude of the reactive force exerted on it by pin B when = 90.
19-35 The 10 kg bullet having of 800 m/s is fired into the edge of the 5 kg disk as shown. Determine the angular velocity of the disk just after the bullet becomes embedded into its edge. Also, calculate the angle the disk will swing when it stops. The disk is originally at rest. Neglect the mass of the rod AB.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
17-35. The sports car has a mass of 1.5 Mg and a center of mass at G. Determine the shortest time it takes for it to reach a speed of 80 km/h, starting from rest, if the engine only drives the rear wheels, whereas the front wheels are free rolling. The coefficient of static friction between the wheels and the road is u, = 0.2. Neglect the mass of the wheels for the calculation. If driving power could be supplied to all four wheels, what would be the shortest time for the car to reach a speed of 80 km/h? G 0.35 m A -1.25 m-- -0.75 m
5. The 25-kg block AA is released from rest.
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
15-51. The 30-Mg freight car A and 15-Mg freight car B are moving towards each other with the velocities shown. Determine the maximum compression of the spring mounted on car A. Neglect rolling resistance

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS