2. A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end plate as shown in Fig. 2. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has diameter 30 mm, the brass tube has outer diameter 45 mm, and the copper tube has outer diameter 60 mm. The corresponding moduli of elasticity are Esteel= 210 GPa, Ebrass= 100 GPa and Ecoper =120 GPa respectively. Calculate the compressive stresses developed Osteel , Obrass, and Ocoper in the steel, brass and copper respectively. (5) P = 40 kN Copper tube Brass tube Steel core 30 mm 45 mm 60 mm Fig. 2

2. A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end plate as shown in Fig. 2. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has diameter 30 mm, the brass tube has outer diameter 45 mm, and the copper tube has outer diameter 60 mm. The corresponding moduli of elasticity are Esteel= 210 GPa, Ebrass= 100 GPa and Ecoper =120 GPa respectively. Calculate the compressive stresses developed Osteel , Obrass, and Ocoper in the steel, brass and copper respectively. (5) P = 40 kN Copper tube Brass tube Steel core 30 mm 45 mm 60 mm Fig. 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure of a liquid is increased from 60 N/cm^2 to 100 N/cm^2 and volume decreases by 0.2 percent. Determine the bulk modulus of elasticity in N/cm^2.
Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are in full contact. In the vertical direction, a uniform pressure force acts on body 1 with 120MPa and on body 2 with 40MPa. Calculate all the stresses in objects 1 and 2 and the length changes in the z-axis direction.Elasticity modules:E1 =180GPa, E2 =100GPaPoisson ratios:v1 =0.4, v 2=0.2
1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
A plastic rod with length and radius of 300 mm and 30 mm, respectively. If an axial force of 400 N is applied, estimate the length and diameter change. Young’s modulus and Poisson’s ratio of the material are 2.7 Gpa and 0.4 respectively.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
An air compressor used by a mechanic for filling air in tyre is cylindrical in shape which has internal diameter and thickness of 600mm and 20mm respectively. If the compressor is subjected to an internal pressure of 30N/mm2 determine the increase in volume of the cylinder. The cylindrical compressor has a length of 2m and the material used m manufacturing the cylinder has elasticity,E=2*105N/mm2 and Poisson's ratio,1/m= 0.3.
Given the problem: The smooth disk shown in the figure is pined at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: a.) Total reaction at 'A' in lb. b.) Horizontal component at 'B' in lb. c.) Vertical component at 'B' in lb. *Round off final answer in 4 decimal places. Thank you.
A cube of side 50 mm is subjected to a pressure of 80 MPa in a pressure chamber. Determine the change in the length of cube if it has a modulus of elasticity of 200 GPa and Poisson's ratio of 0.3.
Q/In the given figure, a horizontal rigid is supported by a pin connection at point A and an axial member (1) at point C. Member (1) has a cross-sectional area of A1 = 1.5 in.2, an elastic modulus of E1 = 10600 ksi, and a coefficient of thermal expansion of α1 = 12 *10-6/°F. Upon applying a load P and simultaneously increasing the temperature by ΔT = 80 °F, the strain in element (1) is observed to increase by ε1 = 1700 με. What is the magnitude of force P? [a = 45 in., b = 32 in., L1 = 55 in.] The answer in kips ?
A shaft having length equal to 10 m and diameter equal to (50 +9) mm is simply supported at both ends. The shaft carries four masses (150 + 9) kg, (200 + 9) kg, (250 + 9r) kg and (300 +9) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A steel block has a length of 80 mm, width of 60 mm and thickness of 40 mm. The block is subjected to a uniform hydrostatic pressure of 180 kPa on all its faces. Modulus of elasticity E=200 GPa, Poisson’s ratio ?= 0.29. a.) Determine the bulk modulus of steel, b.) Determine the dilatation (e) of the material if e is the negative of the ratio of load to bulk modulus., and c.) Determine the change in volume of the steel block.