2. The resistance of a copper wire used to make a motor is 0.5 Ω at 25oC and 0.8 Ω at the motor’s operating temperature. Determine the operating temperature and the rise in temperature of the motor, given that copper has a temperature constant o

2. The resistance of a copper wire used to make a motor is 0.5 Ω at 25oC and 0.8 Ω at the motor’s operating temperature. Determine the operating temperature and the rise in temperature of the motor, given that copper has a temperature constant o

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.1P: Consider a flat plate or a plane wall with a thickness L and a long cylinder of radius r0. Both of...

See similar textbooks

Related questions

Q: A copper conductor has a resistance of 80 Ω at room temperature. If resistance temperature…

A: Given Data→ Resistance of the copper conductor R=80Ω At room temperature Resistance temperature…

Q: The figure below shows a conducting rod sliding along a pair of conducting rails. The conducting…

A: According to the given information we have to find the terminal speed Therefore, as a moving force…

Q: A 9 kg weight is attached to a spring with constant k = 144 kg/m and subjected to an external force…

Q: What is the effective component applied on the box that is being pulled by a 30 N force inclined at…

Q: 14-Two wires have the same length and the same resistance. One is made from aluminum and the other…

Q: O The maximum power cannot be determined without knowing the resistance of the external circui O 7.5…

A: V = IR I = V/R = 1.50/0.30 = 5 Amp power = P = VI = 5 * 1.5 = 7.5 W Option 1st is the wright answer

Q: What is the resistance R of a length of copper wire whose length = 10 m and whose diameter = 0.10

Q: Define the electrical power in terms of resistance R, current I, and potential difference V.

Q: Consider a Wheatstone bridge circuit that has all resistances equal to 100 Ω. The resistance R1 is a…

A: = Wheatstone bridgeSince R1 in a strain guage of 100-Ω resistance . ∵R1=Re=R3=R4=100-e.

Q: The reading of a spring balance is from 0 to 200 N and is 10 cm long. A body suspended from the…

A: Given, Weight capacity of spring balance = W = 200 N Maximum reading = x = 10 cm = 0.1 m Natural…

Q: When a 3-kg collar is placed upon the pan which is attached to the spring of unknown constant, the…

Q: 1. A capacitor of 3.23µF has an area of 6.35mm^2. Determine the separation distance between the two…

Q: When the heat gain is less than the heat losses, then Select one: a. We will need a cooling system…

A: option 1 is the correct answer. i.e. we need a cooling system we know that energy balance…

Q: A RTD made up of platinum has a=0.00385 and has a initial resistance of 360. Find the value of…

Q: A conductor made of nickel (pe=6.8 10- 8V m) has a rectangular cross section 5 x 2 mm and is 5 m…

A: Solution:

Q: A spring with 25 active coils cannot be accommodated within the given space, hence 5 coils were cut.…

Q: 21. Determine the equivalent resistance, Ry, of the circuit shown. 6Ω 10 Ω 15 Ω Μ 30 Ω 12 Ω α Ω Μα…

Q: 1. A spring has a characteristic of k = 2.75N/m. It has an original length of 0.100 m. What is its…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A certain toaster has a heating element made of Nichrome resistance wire. When the toaster is first…

Q: Example 1.6 Solid copper wire having a diameter of 1.63 mm is used to provide electrical…

A: We have, diameter of the cross-section of the wire, d=1.63mm=1.63*10-3m Length of the wire, l=75m…

Q: e a kitchen oven with cork board (k = 0.043 W/mK) so that the heat losses from the oven does not…

Q: The thermocouple circuit represents a T-type thermocouple with the reference junction having T2…

A: Given data: T-type thermocouple with the reference junction T2 is=25°C The output emf of the…

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.00188…

A: Write the expressions of normal strains. εx=1Eσx-νσy0.001884=1200×109σx-0.28σyσx-0.28σy=94×106…

Q: 5. A 1.2 m long conductor is made of a mixture (i.e. alloy) of different materials. The resistivity…

Q: 1. Determine the equivalent spring constant. ki k2 ks 1000

A: The equivalent stiffness of springs can be find out by following ways: 1: springs 1 and 3 are…

Q: Determine the resistance of 1200 m of copper cable having a diameter of 12 mm if the resistivity of…

A: Write the given values with suitable variables. L=1200 md=12 mmr=d2=12 mm2=6 mm=0.006 mρ=1.7×10-8…

Q: Problem 1) Determine the spring constant, k if the unstretched length of the spring is 3.2 meters…

A: Given Data: Unstretched length, L=3.2 m

Q: A bimetallic strip is used as a sensor. The strip has a length of 20 μm. The width of the strip is…

Q: (i) Three identical capacitors are connected in delta with 400 V. If the line current is 12 A…

A: (i) Voltage, VL=440VLine current, IL=12A As in delta connection,Phase voltage,Vp=line…

Q: The characteristics of a vibrating mechanical system can be represented by an electric circuit.…

A: Basics of MECHANICAL VIBRATION.

Q: 2.2 A spring-mass system has a natural period of 0.21 sec. What will be the new period if the spring…

A: Given data:

Q: A six-pole lap wound armature rotating at 350 rpm is required to generate 260 V. The effective flux…

Q: Nonmetallic-Sheathed Cable (NM) shall be permitted to be derated from the 90 degrees C temperature…

A: Non metallic sheathed cable shall be permitted to be derived from the 90degrees C temperature rating…

Q: Which of the following thermocouples can measure temperature in a comparatively high range? 1)…

A: Platinum-rhodium thermocouples are too called high-temperature valuable metal thermocouples. The…

Q: Q1: Answer the following: a) A cable consists of 100 m of copper wire having a cross-sectional area…

Q: The table t value associated with the upper 5% of the t distribution and 12 degrees of freedom is…

Q: The coil relays take a current of 0.12 A when it is at the room temperature of 15°C and connected…

Q: The two metallic strips that constitute some thermostats must differ in: A) length B)…

Q: For the clamping network, the magnitude of must be chosen to ensure that the voltage across the…

A: Option a is correct.

Q: Calculate the strain experienced by a rod of length 2m subjected to a force that causes a change of…

A: Resistance can be Determined as,

Q: Calculate the maximum force P that can be applied in a phosphor bronze spring having mean diameter…

Q: The device has a mass of 180 kg and a specific frequency of 100 Hz. What is the vibration amplitude…

Q: A metal bar at a temperature of 200F is placed in a room at a constant temperature of 20F. (a) If…

A: Given data:

Q: Fourier rate equation predicts that the temperature difference is not inversely proportional to the…

A: Fourier law of heat conduction is "Rate of heat transfer in material is directly proportional to the…

Concept explainers

Electric Heating Unit

An electric heating unit, or an electric unit heater, is designed to warm up spaces and is available in various types suitable for a range of applications. The method of transforming electrical energy to heat energy is called electric heating. An electric heater converts electric currents to heat using an electrical resistor (heating element).

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Nonmetallic-Sheathed Cable (NM) shall be permitted to be derated from the 90 degrees C temperature rating provided the final derated ampacity does not exceed that for ________. A. 50 degrees CB. 60 degrees CC. 75 degrees CD. 90 degrees C
An electric train made up of two cars, each weighing50,000lb, is connected by couplings of stiffness equal to16,000lb/in., as shown in the figure below. Determine the natural frequency of the system.
What is the resistance R of a length of copper wire whose length = 10 m and whose diameter = 0.10 mm?
A copper conductor has a resistance of 80 Ω at room temperature. If resistance temperature coefficient of copper 0.003899 (1/˚C). Calculate the resistance if the temperature is increased to 75˚C.
A coil consists of 2000 turns of copper wire having a circular - section of diameter 2.5 mm. The mean length per turn is 80 cm and the electrical resistivity of copper is 0.02 μΩ–m. Determine the resistance of the coil.
A certain toaster has a heating element made of Nichrome resistance wire. When the toaster is first connected to a 120 V source of potential difference (and the wire is at a temperature of 20.0°C), the initial current is 1.90 A, but the current begins to decrease as the resistive element warms up. When the toaster reaches its final operating temperature, the current has dropped to 1.5 A. (d) Determine the operating temperature of the heating element.
Initially, the temperature of an object is 70 degrees celsius, it is taken outside. The temperature of the surrounding is 20 degrees celsius at 3:03 Pm, the temperature of the body becomes 42 degrees celsius. Later, the object is then taken back inside where the temperature is 80 degrees celsius. At 3:10 PM, the temoerature of the object is 71 degrees celsius. Determine the time when the object is brought inside.
The figure below shows a conducting rod sliding along a pair of conducting rails. The conducting rails have an angle of inclination of θ = 32.0 degrees. There is a resistor at the top of the ramp that connects the two conducting rails (R = 1.5 ohms). The mass of the rod is 0.43 kg. The rod starts from rest at the top of the ramp at time t = 0. The rails have negligible resistance and friction, and are separated by a distance L = 15.3 m. There is a constant, vertically directed magnetic field of magnitude B = 1.40 T. What is the rod's terminal speed?
Give definition of unreliability F(t)of a component as function of time.
Three parallel springs have stiffness constant of 100 N/m each. Determine the spring stiffness equivalent of the springs. 300 N/m 0.01 N/m 100 N/m 33.3 N/m
5. A round aluminum sleeve with an outer diameter of 300 mm and an inner diameter of 200 mm is pressed onto a round steel sleeve with an inner diameter of 100 mm. The radial interference between the two sleeves is 6 = 0.25 mm. Let Ex = 72 GPa, VA = 0.33, E, = 200 GPa and v; = 0.29. Determine the following: (19 points) The interference pressure, p. in MPa between the two sleeves The change in the inner radius in the aluminum sleeve, u, in millimeters If the allowable tangential stress, do, in the aluminum is 180 MPa, determine the safety factor in the aluminum with respect to failure due to tangential stress. You may ignore the radial stres 7
Three springs A, B, and C has spring constants 641 N/mm, 495 N/mm, 541 N/mm respectively. Determine the equivalent spring constant if the springs are in PARALLEL.