2.63. Consider a discrete-time system with input x[n] and output y[n]. When the input is 1-(1) ¹4 the output is x[n]- u[n]. xn- Determine which of the following statements is correct: • The system must be LTI The system could be LTI The system cannot be LTI If your answer is that the system must be or could be LTI, give a possible impulse response. If your answer is that the system could not be LTI, explain clearly why not.

2.63. Consider a discrete-time system with input x[n] and output y[n]. When the input is 1-(1) ¹4 the output is x[n]- u[n]. xn- Determine which of the following statements is correct: • The system must be LTI The system could be LTI The system cannot be LTI If your answer is that the system must be or could be LTI, give a possible impulse response. If your answer is that the system could not be LTI, explain clearly why not.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8.17 MECT361 Mechatronics Components and Instrumentation Prove Equation 8.14. 8.14. Visit Microchip’s website ( www.microchip.com ) and find specifications for the MCP32X series of A/D converters. What is their resolution? What type of architec- ture is used in obtaining the binary representation of the analog value? PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
b[n] - b[n-1] = a[n] -2a[n-1] + a[n-2] The above expression describes the output,b[n] & input,a[n] of a certain discrete time system. Assumption: Input, a[n] to the system is described by a[n] =5δ[n] i. Make a sketch of the output,b[n] & input,a[n] for n= -1 : 5 ii. Determine the output,b[n] for n= -1 : 5
Determine the input – output relation of the combined system; S1 connected in series with S2, i.e., S=S1.S2
(006) (2)- Problem - Common Emitter-Follower Amplifier. (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
A. Give 3 possible problems rn that can relate on electrical engineering and give a solution that can aware public.
Design a circuit that can detect the sequence '101101' anywhere in input, and outputs as 1 in that case. Consider overlapping in this scenario. Perform the following tasks: 1. Draw the state diagram. 2. Implement the State Table.
Design a circuit that can detect the sequence ‘101101’ anywhere in input, and that outputs as 1 in that case. Consider overlapping in this scenario. Perform the following tasks: ⦁ Draw the state diagram ⦁ Implement the State table
Find the input-output relation for the following system.The system is serial and it is S=S1.S2
Design and implement (draw the circuit) the output f(12) of a 7 segments decoderas a function of the binary inputs (W,X,Y,Z).You need the complete the following steps:1. Find the f(12) outputs values (0 or 1) for each number from 0 – 112. Enter these values into a Karnaugh map.3. Simplify the map.4. Draw the circuit using Tina or any other simulation software.
DIGITAL SIGNAL PROCESSING Refer to image given,please solve the question as with step; (a)You are required to evaluate the convolution, y(n) = x(n) ∗ ℎ(n) using graphical method. (b)Sketch the output of signal, y(n).
(004) (1)- Problem - Common Emitter Fixed Bias Amplifier. (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
(please do a and b sub questions) Design a combinational circuit with 4 inputs, A3, A2, A1, A0; and three outputs, X, Y, Z. The inputs represent a binary number in the range [0..15], and the outputs represent characteristics of the numbers. Specifically, X should be true if the number is divisible by 3; Y should be true if the number is prime; and Z should be true if the number is a power of 2. As an example, if the input is A3A2A1A0= 1100, this represents the number 12, which is divisible by 3, not prime, and not a power of 2 so the outputs should be XYZ =100. Recall that 0 is divisible by any integer. (a) Implement the circuit with AND gates, OR gates, and NOT gates. inverted inputs are OK. You may use the k-map template provided for your design work. You may use inverted inputs on gates. (b) Implement the circuit using AND, OR, NOT, and XOR gates. How much simpler is this design than the design in part (a)?