3 For the following numerical values, determine theaverage power P, the reactive power Q, and thecomplex power S of the circuit shown in Figure P7.23.Note: phasor quantities are rms.a. vs(t) = 450 cos (377t) V%3Di(t) = 50 cos(377t – 0.349) Ab. Vs = 14020 VİL = 5.852(-1/6) Ac. Vs = 5020 VÎ, = 19.220.8 Ad. Vs = 7402(-1/4) VÎ = 10.82(–1.5) Aiz(t)vs(t)(ZŁ

(a) Write the given values of voltage and current and write them in phasor form.

Answered: 3 For the following numerical values,…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7MCQ

See similar textbooks

Similar questions

1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Find the apparent power and the real powerdelivered to the load in the Y-Δ circuit shown in FigureP7.74. What is the power factor? Assume rms values
Analyze the impact of harmonics in power systems and propose mitigation techniques.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3.and ??Find the value of the maximum average power transferred to?
In the circuit in the figure, there is a load formed by connecting the resistor R0 between the terminals a and b and the inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volts, the phase angle θs = 0 degrees, the period is T = 200π microseconds. Since R = 300OHM and C = 1 microFa) If the load phase angle is constant θL = 60 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit.b) Calculate the average power on the load.
For an ac circuit consisting of a load connected to a Thévenin circuit, is it possible for the load voltage to exceed the Thévenin voltage in magnitude? If not, why not? If so, under what conditions is it possible? Explain.
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
Given the applied source and network below: a. Determine the sinusoidal expression for the source voltage ?? b. Find the sinusoidal expressions for the currents ?1 and ?2.
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the VS (t) voltage is √2 150 volts, phase angle = 0 degrees, period T = 200π microseconds.Since R = 300 ohms and C = 1 microfarad a)Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit when the load phase angle is constant at 45 degrees? b)Calculate the average power on the load?
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning