3 litters, 4 cylinders engine, multipoint port fuel injection, one for each cylinder. AF ratio is 14.6, the volumetric efficiency is 90%. The engine speed at idle condition is 550 rpm with stoichiometric gasoline and inlet pressure is 30 kPa. But the engine speed is 5900 rpm with stoichiometric gasoline of maximum power, the inlet pressure is 101 kPa. Calculate the following: a. mass air flow rate in one cylinder at maximum speed, b. mass fuel flow rate into one cylinder through an injector, c. mass air flow into one cylinder at idle speed, d. mass fuel flow rate into one cylinder at idle speed, e. injection pulse duration is seconds at idle conditions at idle, f. injection pulse duration is degrees of engine rotation at idle conditions.

Question

 3 litters, 4 cylinders engine, multipoint port fuel injection, one for each cylinder. AF ratio is 14.6, the volumetric efficiency is 90%. The engine speed at idle condition is 550 rpm with stoichiometric gasoline and inlet pressure is 30 kPa. But the engine speed is 5900 rpm with stoichiometric gasoline of maximum power, the inlet pressure is 101 kPa. Calculate the following: a. mass air flow rate in one cylinder at maximum speed, b. mass fuel flow rate into one cylinder through an injector, c. mass air flow into one cylinder at idle speed, d. mass fuel flow rate into one cylinder at idle speed, e. injection pulse duration is seconds at idle conditions at idle, f. injection pulse duration is degrees of engine rotation at idle conditions.

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

IC Engines

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: Consider the following steady, three-dimensional veloc ity field in Cartesian coordinates: V-› = (u,...

A: Any given flow is incompressible if the divergence of its velocity field is zero.

Q: " In regions far from the entrance, fluid flow through a circular pipe is one dimensional, and the v...

A: Given data as per question umax = 6 m/s  R = 0.08 m  L = 30m

Q: An ideal Brayton cycle with regeneration has a pressure ratio of 10. Air enters the compressor at 30...

A: Given data: *The pressure ratio of the cycle is r=10. *The initial temperature of the air is T1=300 ...

Q: Consider a 20-cm-diameter spherical ball at 800 K suspended in air. Assuming the ball closely approx...

A: Given data as per question Diameter of sphere = 20 cm Sphere temperature = 800 k wavelength = 3um

Q: Determine an expression for the velocity va of the cart A down the incline in terms of the upward ve...

A: Click to see the answer

Q: An oil is in laminar flow in a ½ in ID tube at 6 gal/min. The oil viscosity is 300 centipoise, and i...

A: Click to see the answer

Q: If d = 450 mm, determine the absolute maximum bending stress in the overhanging beam.

A: Given data Uniformly distributed load = 8KN/m Depth of the beam d = 450mm Point load at the over han...

Q: C8-49 A 500-lb load is supported by a roller on a beam as shown in Fig. Show that the maximum bendin...

A: Click to see the answer

Q: State newton's second law of motion.

A: There are 3 laws that are proposed by Newton. These are given as, (1) Newton’s first law- Law of ine...

Q: 6-53 Determine the force exerted by the cable at B and the reaction at support A of the bar shown in...

A: Drawing the free body diagram of the system, T is the force in cable. Taking the moment about A,  

Q: Q3 For the system shown determine the moment about points (a) and (b)

A: Click to see the answer

Q: Consider water initially at 20°C and 1 atm. Determine the final density of the water (a) if it is he...

A: Click to see the answer

Q: The diffuser in a jet engine is designed to decrease the kinetic energy of the air entering the engi...

A: Given Data: The exit pressure of jet is: P2=200 kPa The inlet pressure of the jet is= P1=100 kPa Th...

Q: An old gas turbine has an efficiency of 21 percent and develops a power output of 6000 kW. Determine...

A: Given Data: The turbine efficiency is: η=21 % The power developed in output is: W=6000 kW The heati...

Q: Briefly outline the impact that job sequence has on each of the layout types.

A: Job sequence analyses the arrangement and workability of equipment in a layout. The layout has been ...

Q: A block with a mass of 100 kg slides down an inclined surface that is 5 m long and makes an angle of...

A: Click to see the answer

Q: What is the pressure drop in psi of 60°F water flowing through 65 ft of horizontal 1-inch schedule 4...

A: Consider the solution below

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to...

A: Draw the free-body diagram of the shaft.

Q: The beam is made of oak, for which Eo = 11 GPa. Determine the slope and displacement at point A.

A:  

Q: At what instance would you consider using a belt or chain drive system instead of a gear transmissio...

A: Click to see the answer

Q: A certain torpedo, moving in fresh water at 10 8 C, has a minimum-pressure point given bythe formula...

A: Given data: Pmin = P0 - 0.35 ρV2 P0 = 115 kPa The torpedo is accelerating from zero velocity to V. D...

Q: Three identical fatigue specimens (denoted A, B, and C) are fabricated from a nonferrous alloy. Each...

A: Click to see the answer

Q: The 3 × 4-m side AB of a tank is hinged at its bottom A and is held in place by a thin rod BC. The m...

A: Draw the FBD for a better understanding of the problem. Centroidal depth for the triangular body is...

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the pr...

A: The data given is, Normal stress, ?x = -25 Mpa Normal stress, ?y = 0 Shear stress, τxy = 100 MPa  ...

Q: Use the method of joints to determine the force in each member of the truss shown in the following p...

A: Click to see the answer

Q: Two friction disks A and B are brought into contact when the angular velocity of disk A is 240 rpm c...

A: Given Diameter of disc A is 150 mm = 0.15 m RPM disc A = 240 rpm Counter clockwise Diameter of disc ...

Q: Identify five (5) observations of a machine operator’s station which could suggest that the machine ...

A: Ergonomics deals with the relation between a machine and the people using it, It deals with the post...

Q: Q4 for the system shown determine the moment of couples

A: Click to see the answer

Q: Mechanical Engineering Question

A: (a) Draw the free body diagram.

Q: What are the different mechanisms for transferring energy to or from a control volume?

A: The different mechanisms for transferring energy from  or to a control volume mainly by three method...

Q: 6-100 Abracket is loaded and supported as shown in Fig. Determine the reactions at supports A and B....

A: The free body diagram is shown below with the reaction forces acting at A & B . As A is hinge so...

Q: Customers arrive at a bakery at an average rate of 18 per hour on weekday mornings. Thearrival distr...

A: Given Data: The average arrival rate is: λ=18 per hour The mean exponential distribution is: µ=3 mi...

Q: C6-71 The hydraulic cylinder BC is used to tip the box of the dump truck shown in Fig. P6-71. If the...

A: From the above figure,

Q: Mechanical Engineering Question

A: Click to see the answer

Q: What happens if the principal stresses at a critical point in the material?

A: First, define the critical point. Critical points are those points in the given plane where the effe...

Q: Convert between energy units. 2.85x10^3 J to cal

A: Understand that the joule is the SI unit of energy and Calorie is used as the unit of energy in the ...

Q: Briefly explain the different categories of torts law. As an engineer, how the tort law is important...

A: Tort laws are basically the type of law that covers most of the civil suits. By and large, it is obs...

Q: 2-79. Determine the projected component of the force FAB = 560 N acting along cable AC. Express the ...

A: Given data Load in the member AB is FAB = 560N To determine FAB acting along cable AC and resultant...

Q: stress (Hpa> Find 8e Ys= ? 7e1=? 500 400 ZRA-? Ts 2 frachere ? 30 602 004 0.08 strain (un/mm)

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the refrigerate...

A: On using the saturation table of R-134a, the enthalpy of the inlet of the condenser at P1 = 1.2 MPa ...

Q: Can you please do P7.41   Thx

A: The loading diagram of the beam is shown as follows, Let's draw the free body diagram of the beam,

Q: A uniform circular rod of weight 8 lb and radius 10 in. is attached to a pin at C and to the cable A...

A: Draw the FBD diagram showing the thin homogenous wire. Part a) Find the centroidal axis for the qua...

Q: For what uniform rotation rate in r/min about axis C willthe U-tube in Fig.  take the confi guration...

A: Click to see the answer

Q: The maximum flow rate of a standard shower head is about 3.5 gpm (13.3 L/min) and can be reduced to ...

A: Given data: Maximum flow rate = Q1 = 13.3 L/min Flow rate after reduction, Q2 = 10.5 L/min Number of...

Q: Determine the magnitude of the resultant force acting on the bracket and its direction measured coun...

A: Click to see the answer

Q: How many significant figures are in number? 312,000 s

A: Click to see the answer

Q: The cable shown in Fig. weighs 35 N/m. Determine the maximum tension in the cable and the sag ha in ...

A:  Determine the central dip by using the below expression.    

Q: Locate the centroid y¯ of the channel's cross-sectional area. Then determine the moment of inertia w...

A: C

Q: Determine the maximum and minimum second moments of area with respect to axes through the origin of ...

A: We can divide the entire area into a rectangle (1) and a rectangle (2). We will first determine the ...

Q: 13-37. If the 75-kg man stands in the position shown, determine the state of stress at point A on th...

A: Click to see the answer