3. A 10ohms resistor and an unknown inductance is connected in series. The series combination is then connected to a 10V DC source. After 1 sec the voltage measured across the inductor is 3V. Find the value the unknown inductance for this condition. Use the false- position method to determine L to a level of Es = 0.1%. Employ initial guess of x₁ = 6 and x₂ = 10

3. A 10ohms resistor and an unknown inductance is connected in series. The series combination is then connected to a 10V DC source. After 1 sec the voltage measured across the inductor is 3V. Find the value the unknown inductance for this condition. Use the false- position method to determine L to a level of Es = 0.1%. Employ initial guess of x₁ = 6 and x₂ = 10

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Electrical Engineering --question 1-- Calculate the theoretical voltages across the resistor and inductor for 10 kHz and 60 kHz using the 680Ω theoretical resistance, 3.3 mH inductance, and 5-V source. Demonstrate the step-by-step process. Answer must be in Polar form. --question 2-- Calculate the theoretical voltages across the resistor and capacitor for 500 Hz and 1750 Hz using the 680Ω theoretical resistance, the observed capacitance, and the 5V source. Demonstrate the step-by-step process. Answer must be in Polar form.
For the circuit below, R1 is given by the "6". The value of capacitorC1= 15 µF. a-) find ?0(?) for ? > 0. Deteremine the time constant and find the time necessary for the capacitor voltage to decay to one-tenth of its value at t = 0. Sketch the voltage on the capacitor.b-)Add another capacitor with same value in parallel. What will be the total capacitance. Find the time constant. Which parameters will be affected by the addition of the capacitor? Explain. Draw the input and output waveforms
For the circuit shown in figure below, find the equivalent capacitance (Ceq) of the combination.
Describe the behavior of the following circuit under the following scenario: (1) Begin with switch S1 open, (2) close switch S1 long enough till the voltage across the inductor is almost zero, and then (3) open switch S1 for a long time beginning at time t = 0.
How come you have not taken into consideration the impedance of the inductor in the first part of the solution when calculating the current?
V(t) = V0e^-t/rc where V(t) is the voltage across the capacitor after it's been discharging for an amount of time t, V0 is the voltage it started at, C is the capacitance of the capacitor, and R is the resistance of the resistor it's discharging through. One thing we can take away from this is that, after it's been discharging for an amount of time t = RC, the voltage across the capacitor will be V0e^−1, which is about 37% of the voltage it started at. In other words, RC, the resistance times the capacitance, is the amount of time it takes the capacitor to discharge from 100% voltage to 37% voltage. (The units check out, by the way: 1Ω⋅1F=1sec) If you have an RC circuit with a 10 mF capacitor and a 2 kΩ resistor, about how long will it take the capacitor to discharge to 37% of its original voltage? Group of answer choices 100 s 5 s 12 s 20 s
Consider a tank circuit consisting of a 15 µF capacitor and a 15 mH inductor connected in series. At t=0 there is 2.2 mJ of energy stored in the capacitor and 2.2 mJ stored in the inductor, and the capacitor is discharging. (a) How much charge is on the capacitor at t=0 seconds? (C) (b) How much current is in the inductor at t=0 seconds? (A) (c) How much time will elapse until the first instance when the stored energy is entirely in the inductor? (seconds) (d) How much time will elapse until the first instance when the stored energy is entirely in the capacitor? (seconds)
A series RC circuit is not switched on and the initial state charge of capacitance ?CO = 10 V. In the circuit voltage source E = 50 V DC. Resistance R = 44 Ω and capacitance C = 100 μF. Give the answers to two decimal places. a) Give time constant Tau of circuit (ms) b) Calculate current after the switch k is closed at the moment t = 0.2 ms. (A) c) Calculate current after the switch k is closed at the moment t = 2*Tau. (A)
A series circuit consisting of an inductor, a resistor, and a capacitoris open. There is an initial charge of 2 coulombs on the capacitor,and 3 amperes of current is present in the circuit at the instantthe circuit is closed. A voltage given by E(t) = 20 cos t is applied.In this circuit the voltage drops are numerically equal to thefollowing: across the resistor to 4 times the instantaneous changein the charge, across the capacitor to 10 times the charge, andacross the inductor to 2 times the instantaneous change in the current.Find the charge on the capacitor as a function of time. Determinethe charge on the capacitor and the current at time t = 10.