31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A wear allowance of 5% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the GO gage. Round your answer to the nearest tenth of a thousandth of a inch

31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A wear allowance of 5% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the GO gage. Round your answer to the nearest tenth of a thousandth of a inch

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 10RQ: List and briefly describe the three types of tolerances used on prints.

See similar textbooks

Related questions

Q: 1) discuss the methods of measurement and what is the accurate method 2) What is the micrometer .and…

A: The comparison of the standard and the unknown amount yields the measurement. In other words,…

Q: What is a transfer-type measuring tool?

A: Precision measurements are those with an accuracy of 0.5 mm or 1°. These measurements are necessary…

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: The company produced a new product intended to measure diameter profiles. In a run test conducted,…

A: 1). Precision- option B is correct Accuracy is how close or far off a given set of measurements are…

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: I need help solving problems 1, 2, and 3 pertaining to the blueprint attached below.

A: There are four surface texture symbols are used in the given drawing as shown in the fig.

Q: 6. What is accuracy in measurement?

A: Measurement: It is the numerical quantification of the attributes for a body that are used to…

Q: Compare one point vs two point calibration: explain how it affects the measurement curve and…

A: The simplest sort of calibration is one point calibration. A one-point calibration can be…

Q: I need answers to these 3 parts for a review activity.

A: An italic f indicates finish, the v symbol and check mark type symbol also represents the surface…

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: 20 13. On the part above, what is the flatness on the top surface with only the profile applied? Top…

Q: What is the algebraic difference between the lowest limit of size dmin and the nominal size da (dmin…

A: The correct option is 4 (the lower deviation ei), Lower deviation is the algebraic difference lower…

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:- 1.GO end gauging :- Go end used in qualify the…

Q: (USCS units) A sine bar is used to determine the angle of a part feature. The length of the sine bar…

Q: 2. Form tolerances are independent of all other Features Size Limits Datums ?

A: Form tolerance is a geometric tolerance that defines the roundness, flatess, straightness of a part.

Q: Given the following sentence descriptions of the geometric tolerance information, correctly sketch…

Q: (USCS units) A GO/NO-GO plug gage is needed to inspect a 1.000 ± 0.020 in diameter hole. A wear…

Q: Circular blanks having following data; Diameter = 35 mm %3D Thickness= 2 mm If the clearance per…

A: Given Data: Diameter of the blank, d=35 mm The thickness of the blank, t=2 mm

Q: The diameters of hole with a nominal size Ø115 must be within limits Dmax = 115.015 mm and Dmin =…

A: Given:D=115 mmDmax=115.015 mmDmin=114.982 mm

Q: Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40…

A: Given Shaft designated as 40H8/f7 Therefore, 40mm id=s…

Q: The found that the dial indicator reading was increasing wi moving in a horizontal line along the…

A: We have to decide what gauge is required next.

Q: Refer to the 1.914 dimension. A) Where is the tolerance specified ?…

A: A) For MMC & LMC Consider ϕ0.8740±0.0005 MMC=0.8740+0.0005=ϕ0.8745 LMC=0.8740-0.0005= ϕ0.8735…

Q: Unless otherwise specified, all tolerances and datum features apply for the full Unless otherwise…

Q: What are the geometry features in the picture below? Indicate main geometry and tolerances

A: Geometry Features which mentioned in the Drawing are as below:

Q: Which type of feature doesn't belong to form tolerances? Circularity The profile of a surface…

A: As we know principle component of form tolerence are Straightness.Flatness.Roundness.Cylindricity.

Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

Q: 1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2.…

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: List and briefly describe the three types of tolerances used on prints.

A: Tolerance is important to factor that will be used to identify the machined or the manufactured…

Q: I need help answering problems 13, 14, and 15 pertaining to the print attatched below.

A: The print sheets attached shows the manufacturing or material part drawing of a mechanical part (her…

Q: For an ordinary concrete slab to be laid" -3 within tolerance, engineers can only realistically…

A: Given question is related to metrology and inspection We have to complete the expression that is…

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Which order arranges the following manufacturing processes from the least precise to the most…

A: The casting is a type of manufacturing process in which the liquid material is poured into a hollow…

Q: You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in…

Q: What are the five principal parts of a micrometer ?

A: Micrometer is a tool which is used to measure micrometer level small measurements.

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

A: MMC or maximum material condition is basically the limit, at which the maximum amount of material…

Q: M5.20 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole.…

A: Go gage will inspect the minimum shaft diameterAnd NO-GO gage will inspect maximum shaft diameter.

Q: Match the following term to the phrase that describes it. I had this question answered but number 3…

A: Tolerance is the amount variation is permitted to vary from the original dimension.

Q: Bilateral tolerance is Total tolerance is in 1 direction only Total tolerance is in both the…

A: As per our guidelines we are supposed to answer first one .Kindly repost other question as a…

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70…

A: Given: Dimensions of,Hole=70+0.00+0.04mmShaft=70-0.08-0.04mm

Q: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

A: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

Q: 36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A…

Q: Please answer #83 82.Given a Ø24±0.25 hole located with a positional tolerance at LMC of Ø0.15,…

Question

100%

31. (USCS units) A GO/NO-GO plug gage will be designed to
inspect a 2.000 0.002 mm diameter hole. A wear allowance of
5% of the total tolerance band is applied to the GO side of the
gage. Determine the nominal sizes of the GO gage. Round your
answer to the nearest tenth of a thousandth of a inch

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

List and briefly describe the three types of tolerances used on prints.
What is a dimensioning tolerance?
A GO/NO-GO snap gage is required to inspect the diameter of a shaft that is 1.000 ± 0.020. A wear allowance of 2% of the entire tolerance band is applied to the GO side. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage
(USCS UNITS) A GO/NO GO PLUG GAUGE WILL BE DESIGNED TO INSPECT A 2.000 +/- 0.002mm DIAMETER HOLE. A WEAR ALLOWANCE OF 5% OF THE TOTAL TOLERANCE BAND IS APPLIED TO THE GO SIDE OF THE GAUGE. DETERMINE THE NOMINAL SIZES OF THE GO GAUGE. ROUND YOUR ANSWER TO THE NEAREST TENTH OF A THOUSANDTH OF AN INCH
Limits and tolerances
Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determine the GO and NO GO plug diameters for a hole with a dimension of φ1.875 + .003. Identify which is the GO plug and which is the NO GO. Please explain
how do you write this in a feature control frame? "The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"
Using the 10% rule of thumb for determining gagemaker’s tolerance for a plug gage, determine the GO and NO GO plug diameters for a hole with a dimension of φ2.375 + .003. Identify which is the GO and which is the NO GO.
Explain what is meant by the tolerance percent defective ?
What are the geometry features in the picture below?Indicate main geometry and tolerances
What is a transfer-type measuring tool?
What is a part's tolerance?