4-40 Steam at 75 kPa and 8 percent quality is contained in a spring-loaded piston-cylinder device, as shown in Fig. P4-40. with an initial volume of 2 m³. Steam is now heated until its volume is 5 m³ and its pressure is 225 kPa. Determine the heat transferred to and the work produced by the steam during this process. www Steam

4-40 Steam at 75 kPa and 8 percent quality is contained in a spring-loaded piston-cylinder device, as shown in Fig. P4-40. with an initial volume of 2 m³. Steam is now heated until its volume is 5 m³ and its pressure is 225 kPa. Determine the heat transferred to and the work produced by the steam during this process. www Steam

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

A vertical piston–cylinder device initially contains 0.01 m3 of steam at 200°C. The mass of the frictionless piston is such that it maintains a constant pressure of 500 kPa inside. Now steam at 1 MPa and 350°C is allowed to enter the cylinder from a supply line until the volume inside doubles. Neglecting any heat transfer that may have taken place during the process, determine the final temperature of the steam in the cylinder.
Two rigid tanks are connected by a valve. Tank A contains 0.25 m3 of water at 450 kPa and 75 percentquality. Tank B contains 0.55 m3 of water at 300 kPa and 250oC. The valve is now opened, and the twotanks eventually come to the same state. Determine the pressure and the amount of heat transfer whenthe system reaches thermal equilibrium with the surroundings at 25oC. Handwritten pls
Water initially at 200kPa and 300°C is contained in a piston-cylinder device fitted with stops.The water is allowed to cool at constant pressure until it exists as a saturated vapor and the piston rests on the stops.Then the water continues to co
A piston-cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the plunger is 0.1 m2. Heat is transferred to the water, causing some of it to evaporate and expand; When the volume reaches 0.2 m3, the piston hits a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the plunger rises a further 20 cm. Determine a) the final pressure and temperature and b) the work done during this process. Also show the process on a P-V diagram.
A piston-cylinder device contains 0.5 kg of air initially at 3 MPa and 250°C.The air is first expanded at the constant pressure to 0.04 m3, thencompressed isothermally to the initial volume, and finally compressedisometrically to the initial state.1. Draw the P-V diagram.2. Determine the boundary work for each process and the net work of thecycle.3. Heat lost during the constant volume process.
A piston-cylinder device contains 50 kg of water at 150 kPa and 25°C. The cross sectional area of theplunger is 0.1 m^2. Heat is transferred to the water, when the volume is 0.2 m^3, the piston makes contact with a linear spring of constant k = 150 kN/m. Heat transfer continues until the spring deforms 30 cm.Make a diagram corresponding to the statement and determine the work done and the total heat transfer.Answer: 33.7275 kJ, 29.333 kJ.
0.03-m of air is contained in the spring-loaded piston-cylinder device shown in Fig. P4-53. The spring constant is 875 N/m, and the piston diameter is 25 cm. When no force is exerted by the spring on the piston, the state of the air is 2250 kPa and 240°C. This device is now cooled until the vol- ume is one-half its original size. Determine the change in the internal energy and enthalpy.
A piston–cylinder device initially contains 2 kg of refrigerant-134a at 800 kPa and 80°C. At this state, the piston is touching on a pair of stops at the top. The mass of the piston is such that a 500-kPa pressure is required to move it. A valve at the bottom of the cylinder is opened, and R-134a is withdrawn from the cylinder. After a while, the piston is observed to move and the valve is closed when half of the refrigerant is withdrawn from the cylinder and the temperature in the tank drops to 20°C. Determine the work done.
A piston–cylinder device initially contains 2 kg of refrigerant-134a at 800 kPa and 80°C. At this state, the piston is touching on a pair of stops at the top. The mass of the piston is such that a 500-kPa pressure is required to move it. A valve at the bottom of the cylinder is opened, and R-134a is withdrawn from the cylinder. After a while, the piston is observed to move and the valve is closed when half of the refrigerant is withdrawn from the cylinder and the temperature in the tank drops to 20°C. Determine the heat transfer.
A piston–cylinder device contains 0.05 m3 of a gas initially at 200 kPa. At this state, a linear spring that has a spring constant of 150 kN/m is touching the piston but exerting no force on it. Now heat is transferred to the gas, causing the piston to rise and to compress the spring until the volume inside the cylinder doubles. If the crosssectional area of the piston is 0.25 m2 , determine (a) the final pressure inside the cylinder, (b) the total work done by the gas, and (c) the fraction of this work done against the spring to compress it.
A piston-cylinder device with a set of stops initially contains 0.5 kg of steam at 1.2 MPa and 500°C. The location of the stops corresponds to 30 percent of the initial volume. Now the steam is cooled. Determine the compression work if the final state is;(a) 1.2 MPa and 200°C.(b) 500 kPa(c) Also determine the temperature at the final state in part (b).
A turbine generates 5 MW of power, using steam at 500°C and 4 MPa which enters the turbine at 20 kg every second with negligible speed. In this turbine the steam expands becoming a saturated vapor at 450 kPa before exiting at the outlet. Determine the rate of heat loss (in kW). Provide your answer to one decimal place.