Answered: 4) Determine the magnitude and…

4) Determine the magnitude and direction of the friction force which the vertical wall exerts on the 40 kg block if (a) 0 = 15° and (b) 8 = 30°.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.48P: Find the smallest distance d for which the hook will remain at rest when acted on by the force P....

See similar textbooks

Related questions

Q: Two blocks A and B meet in contact as shown in the figure. If he coefficients of static friction for…

A: given- weight of block A=200lb weight of block B =100lb…

Q: Two blocks are connected by a solid strut attached to each block with coefficient of friction 0.30…

A: Given Weight of the block B = 300 N Friction coefficient = 0.3 To find Force in the strut Weight of…

Q: A 1500-lbs crate is pulled along the ground with a constant speed for a distance of 25 ft, using a…

A: Given weight of crate (W) = 1500 lbs coefficient of kinetic friction() = 0.55 angle() = 15o distance…

Q: Question 2 If the force P in the structure below is equal to 450 N, determine the maximum mass of…

Q: the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is…

A: Given: The system with force is shown below:

Q: The coefficient of static friction between the 225 kg crate and the ground is μs = 0.3, while the…

A: draw FBD of the system

Q: A 50 kN load is placed on two tires of a locked-wheel trailer. At a speed of 48 km/h, a force of 30…

A: To determine the friction factor

Q: The 561-N force is applied to the 109-kg block, which is stationary before the force is applied.…

Q: QUESTION 13 Block A of mass 180 kg is connected to block B of mass 135 kg by means of a light member…

Q: If the coefficient of static friction at the contact points A and B is μs = 0.4, determine the…

Q: 6/2: The 700-N force is applied to the 100-kg block, which is stationary before the force is…

A: Given data:F=700Nwt=100 kgμs=0.8μk=0.6P=700Nθ=80°To find:-Friction force FsolutionConsider FBD of…

Q: The man is trying to push the homogeneous 20-kg ladder AB up a wall by applying the horizontal force…

A: Given Data: The mass of the ladder is m = 20 kg. The Horizontal force is P. The coefficient of…

Q: From the given figure shown the coefficients of friction are as follows: 0.25 at the floor, 0.30 at…

Q: The man is trying to push the homogeneous 20-kg ladder AB up a wall by applying the horizontal force…

A: When there is any relative motion between any two surfaces, there is a force that opposes the motion…

Q: 4) A worker is pulling down the rope as shown. If the pulleys in the system are frictionless, and…

A: From Lami's theorem, (when three forces act at a point) T1sinα=T2sinβ=Wsinγ

Q: The 381-N force is applied to the 83-kg block, which is stationary before the force is applied.…

Q: Block A weighs 120lb, block B weighs 200lb, and the cord is parallel to the incline. If the…

A: Given Data, WB = Weight of block B= 200 lb WA = Weight of block A= 120 lb μ=Coefficient of friction…

Q: The coefficient of friction is 0.20 between the rope and the fixed drum and between all surfaces in…

Q: Question 8 The ladder AB, of mass 30 kg, is positioned as shown. What is the B direction of the…

A: The direction of friction is opposite to the direction of movement.

Q: 4) A worker is pulling down the rope as shown. If the pulleys in the system are frictionless, and…

A: Let us draw the free body diagram of the pulley Free body diagram of crate

Q: Determine the maximum force P that can be applied without causing the two 50-kg crates to move. The…

A: Given : The mass of each crates = 50 kg The coefficient of static friction between crates and ground…

Q: Question 2: 0.6 m- The uniform 60-kg crate C rests uniformly on a 10-kg dolly D. If the front…

A: The weight of the crate is Wc=mcg=60×9.81=588.6 N The weight of the dolly is WD=mDg=10×9.81=98.1 N…

Q: the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is…

A: Consider the free body diagram:

Q: If the coefficient of static friction between Wedge A and Crate B is 0.32 and between other…

A: Given Data: The coefficient of static friction between wedge A and crate B is, μ1=0.32. The…

Q: Two blocks A and B, each with a mass of 6 kg, are connected by the links shown. If the coefficients…

Q: the block and the incline is 0.25. The dope passes over a drum D, where the coefficient of static…

Q: Q1 - A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

A: 1) To Find : The tension force in the cable. Given : The mass of man is m=75 kg. The mass of box…

Q: 30 kN P 7 kN 20

Q: he conveyor belt is moving downward at 5 m/s. If the coefficient of static friction between the…

A: Given:v=5 m/sm=12 kgμk=0.71

Q: The coefficient of static frictions between the 96-lb body and the 18° wedge is 0.19. Determine the…

A: (a) To find: The magnitude and the direction of the force P. Given: The weight of the body is 96 lb.…

Q: The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

A: Let us draw the free body diagram

Q: Draw the FBD of wedge B and block A when wedge B impends to slide to the right. Friction is…

Q: sing the definition of the static friction and the first condition of equilibrium, show that the…

A: Given: Wooden Cart and pan arrangement as shown

Q: 2. The force P is applied to the block m kg, which is stationary before the force is applied.…

Q: The coefficient of static friction for both wedge surfaces is 0.32 and that between the 36-kg…

Q: A 60 kN load is placed on two tires of a locked-wheel trailer. At a speed of 48 km/h, a force of 30…

Q: Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown. B…

A: Suppose T1 tension in linkage AC and T2 tension in linkage BC. Use Lami's theorem P/sin70 =…

Q: Q2 Determine the reversed horizontal force p needed to pull out wedge A. the coefficient of static…

Q: The 449-N force is applied to the 81-kg block, which is stationary before the force is applied.…

Q: Block A has a mass of 29 kg and block B has a mass of 41 kg. The two blocks are stacked on the ramp…

Q: The 562-N force is applied to the 112-kg block, which is stationary before the force is applied.…

Q: Q3-Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D.…

Q: Block A having a mass of 45 kg rests on block B having a mass of 90 kg, and is tied with a…

Q: The coefficients of static and kinetic frictions between the vertical wall and the 80-1b block are…

Q: 2. The two 200-lb blocks are pushed apart by the 15° wedge of negligible weight. The angle of static…

A: Answer: The force P required to start the blocks moving is 48.6 lb.

Q: (a) Draw the FBD of A and B when the wedge B impends to slide to the left. Friction is negligible…

Q: Q2: Determine the magnitude and direction of the friction force which the inclined pla exerts on the…

Q: A system is in equilibrium with the 150 lbs block having a coefficient of friction of 0.4. Determine…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

4) Determine the magnitude and direction of
the friction force which the vertical wall exerts
on the 40 kg block if (a) 0 = 15° and (b)
8 = 30°.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The 30-lb block is held in place on the smooth inclined plane by the force P. (a) Knowing that =20, determine P. (b) Given that P=40lb, find the angle .
Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
The man pushes the 120-lb homogeneous crate with the horizontal force P. Determine the largest distance h for which the crate will slide without tipping.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The blocks A and B of weights WA and WB are joined by a rope that passes over the fixed peg C. The coefficients of static friction are =0.2 between block A and the inclined plane, and =0.25 between the rope and the peg. Determine the range of Wb/WA for which the system will be in equilibrium.
The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?