4-14. The man uses the hand truck to move material up the step. If the truck and its contents have a mass of 50 kg with center of gravity at G, determine the normal reaction on both wheels and the magnitude and direction of the minimum force required at the grip B needed to lift the load. 0.4 m 0.5 m 0.4 m 60 0.4 m 0.1 m

4-14. The man uses the hand truck to move material up the step. If the truck and its contents have a mass of 50 kg with center of gravity at G, determine the normal reaction on both wheels and the magnitude and direction of the minimum force required at the grip B needed to lift the load. 0.4 m 0.5 m 0.4 m 60 0.4 m 0.1 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.89RP: The woman is trying to move the crate of weight W by pulling on the rope at the angle to the...

See similar textbooks

Similar questions

Find the minimum force P required for impending motion of the block up the inclined surface, given: Mblock = 65 kg, θ = 52 °, μ = 0.4
The three A-36 steel wires each have a diameter of 2 mm and unloaded lengths of LAC = 1.60 m and LAB = LAD = 2.00 m. Determine the force in each wire after the 150-kg mass is suspended from the ring at A.
If cylinder E has a mass of 20 kg and each cable segment can sustain a maximum tension of 400 N, determine the following: 3.1 The largest mass of cylinder F that can be supported by the system is ______ kg. 3.2 The sag yC is equal to ______ m.
The automobile has a mass of 2 Mg and center of mass at G. Determine the towing force F required to move the car if the back brakes are locked and the front wheels are free to roll. Take us=0.3.
Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components ofreaction at the journal bearing C and thrust bearing D if θ = 0°. The bearings are in proper alignment and exert only force reactions on the shaft.
The concrete hopper and its load have a combined mass of 4 metric tons (1 metric tons equals 1000 kg) with mass center at G and is being elevated at constant velocity along its vertical guide by the cable tension T. The design calls for two sets of guide rollers at A, one at each side of the hopper, and two sets at B. Determine the force supported by each of the two pins at B.
The A-36 steel wires AB and AD each have a diameter of 2 mm and the unloaded lengths of each wire are LAC = 1.60 m and LAB = LAD = 2.00 m. Determine the required diameter of wire AC so that each wire is subjectedto the same force when the 150-kg mass is suspended from the ring at A.
3. Determine whether the 10 kg block shown is in equilibrium, and find the magnitude and direction of the friction force when P = 40 N and 0 = 20⁰. μ = 0.30 M = 0.25 20°
The cantilevered jib crane is used to support the load of 780 lb. If the trolley T can be placed anywhere between 1.5 ft ≤ x ≤ 7.5 ft, determine the maximummagnitude of reaction at the supports A and B. Note that the supports are collars that allow the crane to rotate freely about the vertical axis. The collar at B supports a force in the vertical direction, whereas the one at A does not.
The smooth uniform rod AB is supported by a ball-and-socket joint at A, the wall atB, and cable BC. Determine the components of reaction at A, the tension in the cable,and the normal reaction at B if the rod has a mass of 20 kg. Once you have your solution examine the reaction force at A and determine if it points in the direction of the member AB
Find the force F and P acting on the mass M (FBD massA,massB)
The drop gate at the end of the trailer has a mass of 1000 kg and mass center at G. If it is supported by the cable AB and hinge at C. determine the tension in the cable when the truck begins to accelerate at 5 m/s2 to the left.